Following example displays counters for port g1, 134

w w w . d e l l . c o m s u p p o r t . d e l l . c o m

The following example displays counters for port g1.

Console# show interfaces counters ethernet g1


Port	InOctets		InUcastPkts	InMcastPkts	InBcastPkts
------	-----------		--------------	--------------	-----------
g1	183892		1289	987	8
Port	OutOctets		OutUcastPkts	OutMcastPkts	OutBcastPkts
------	-----------		--------------	--------------	-----------
g1	9188		9	8	0
FCS Errors: 8
Single Collision Frames: 0
Multiple		Collision Frames: 0
SQE Test		Errors: 0
Deferred		Transmissions: 0
Late Collisions: 0
Excessive Collisions: 0
Internal		MAC Tx Errors: 0
Carrier Sense Errors: 0
Oversize		Packets: 0
Internal		MAC Rx Errors: 0
Received		Pause Frames: 0

Transmitted Pause Frames: 0

The following table describes the fields shown in the display:

Field	Description

InOctets	Counted received octets.

InUcastPkts	Counted received unicast packets.

134

Ethernet Configuration Commands

Page 134

Image 134

Dell 5324 manual Following example displays counters for port g1, Console# show interfaces counters ethernet g1, 134

5324 specifications

The Dell 5324 is a high-performance network switch that is designed to meet the demands of modern enterprise networking. This switch represents a blend of advanced features aimed at enhancing network efficiency, reliability, and scalability, which are crucial for businesses looking to optimize their infrastructure.

One of the standout features of the Dell 5324 is its Layer 3 routing capabilities. It supports static routing and various dynamic routing protocols, including RIP, OSPF, and BGP, allowing for efficient data transfer across complex networks. This capability is particularly beneficial for organizations that require robust inter-VLAN routing and seamless connectivity with multiple network segments.

The Dell 5324 comes equipped with 24 Gigabit Ethernet ports, which provide ample connectivity options for devices within the network. Additionally, it includes four 10 Gigabit SFP+ ports, enabling users to integrate high-speed uplinks easily. This flexibility allows businesses to expand their network as demand grows without the need for a completely new setup.

Power over Ethernet (PoE) support is another significant advantage of the Dell 5324, as it enables the switch to deliver both data and power to connected devices through a single Ethernet cable. This feature is particularly useful for powering IP phones, security cameras, and Wi-Fi access points, simplifying the overall cabling and ensuring a neater installation.

Furthermore, the Dell 5324 offers advanced security features that help protect the network from unauthorized access and potential threats. It includes features such as 802.1X port-based authentication, MAC address filtering, and VLAN segmentation, ensuring that only authorized devices can connect to the network.

The user-friendly web-based interface alongside command-line interface (CLI) access enhances manageability, allowing network administrators to monitor performance, configure settings, and troubleshoot issues with ease. In addition, the switch supports network automation protocols, which can streamline management tasks and improve efficiency.

The industrial-grade design of the Dell 5324 ensures its reliability in various environments, making it a suitable choice for data centers and enterprise networks alike. With its combination of performance, scalability, and security features, the Dell 5324 stands out as a capable solution for organizations looking to improve their network infrastructure. Its capabilities make it a versatile addition for businesses aiming for a robust and future-ready networking environment.

Contents

CLI Reference Guide Aug Contents Using the CLI Address Table Commands Clock Ethernet Configuration Commands Igmp Snooping Commands Lacp Commands Management ACL Port Monitor Commands Rmon Commands Spanning-Tree Commands SSH Commands Syslog Commands Tacacs Commands Vlan Commands 32 802.1x Commands 382 Page Introduction Command GroupsCommand Groups Configures commands related to 802.1x security protocol Configures and reports on Spanning Tree protocolConfigures Tacacs commands AAA Commands Address Table Commands Defines an authentication key for Simple Configures an external time source forConfigures the system to automatically switch Displays statically created entries in the bridge Configuration and Image Files Commands Ethernet Configuration Commands Displays the backup configuration file contents Gvrp Commands IP Addressing Igmp Snooping CommandsDefines a default gateway router Sets an IP address Cache Line CommandsDeletes entries from the host name-to-address Lldp Commands Sets the line for automatic baud rate detection Management ACL Commands PHY Diagnostics Commands QoS Commands Port Channel CommandsPort Monitor Commands Radius Commands Enables each port trust state Rmon Commands Snmp Commands Spanning Tree Commands MST Sets the default path cost method SSH CommandsOverrides the default link-type setting Syslog Commands Reloads the operating system System Management CommandsTacacs Commands Switches the mode to debug User Interface CommandsVlan Commands Disables the default Vlan functionality Reserves a Vlan as the internal usage Vlan of an Interface Web Server Commands 802.1x Commands Command Description Access Mode Command Groups Command Modes GC Global Configuration Mode Device Notification operation IC Interface Configuration Mode Sntp Reserves a Vlan as the internal usage Vlan of an interface An Extensible Authentication Protocol EAP request/identityFrame, from the client, before resending the request Command Description LC Line Configuration ModeEnables the Simple Network Time Protocol Sntp client on an MA Management Access-level Mode PE Privileged User Exec Mode Vlan SP SSH Public Key Mode UE User Exec Mode Command Modes VC Vlan Configuration Mode W . d e l l . c o m s u p p o r t . d e l l . c o m Introduction Using the CLICLI Command Modes User Exec Mode Privileged Exec Mode Global Configuration Mode Exit End Ctrl+Z Starting the CLI Consoleconfig# username admin password smith Editing FeaturesEntering Commands Command Completion Terminal Command BufferNegating the Effect of Commands Config#interface ethernet Italic font CLI Command ConventionsKeyboard Shortcuts Enter Using the CLI Default Configuration AAA CommandsAaa authentication login Command Mode Example Aaa authentication enableFollowing example configures authentication login Login authentication Console config# aaa authentication enable default enable Enable authentication Console config-line#login authentication default Following example configures the http authentication Ip http authenticationConsole config-line#enable authentication default Following example configures https authentication Ip https authenticationShow authentication methods Privileged Exec mode Syntax Show authentication methods Default ConfigurationThis command has no default configuration Following example displays the authentication configuration Syntax Password password encrypted No password PasswordConsole# show authentication methods Following example specifies a password secret on a line Enable passwordNo password is required No user is defined UsernameShow users accounts Syntax Show users accounts Default Configuration Console# show users accounts AAA Commands Bridge address Address Table CommandsInterface configuration Vlan mode Console config# bridge multicast filtering Disabled. All multicast addresses are flooded to all portsThis example, bridge multicast filtering is enabled Bridge multicast filtering Following example registers the MAC address No multicast addresses are definedExamples No forbidden addresses are defined Command ModesBridge multicast forbidden address Bridge multicast forbidden forward-all Disable forward-all on the specified interfaceBridge multicast forward-all This example all multicast packets on port g8 are forwarded Bridge aging-time Syntax Console# clear bridge Clear bridgeSyntax Clear bridge Port security Disabled No port securityInterface Configuration Ethernet, port-channel mode Show bridge address-table Console config-if#port security routed secure-addressPort security routed secure-address Mac-address-Specify a MAC address in the format Port-channel-number-A valid port-channel number Show bridge address-table static Console# show bridge address-table Syntax Show bridge address-table count vlan vlan Show bridge address-table countConsole# show bridge address-table static Vlan -Specific Vlan Show bridge multicast address-table Console# show bridge address-table count Console # show bridge multicast address-table Console # show bridge multicast address-table format ip Syntax Show bridge multicast filtering vlan-id Show bridge multicast filteringShow ports security Vlanid-A valid Vlan ID value Console # show ports security Clock source ClockClock set Syntax Clock source sntp No clock source Console# clock source sntp Clock timezoneNo external clock source Clock summer-time Sntp authentication-key No authentication key is defined Syntax Sntp authenticate No sntp authenticate Sntp authenticateConsoleconfig# sntp authentication-key 8 md5 ClkKey Sntp trusted-key Sntp client poll timerFollowing example authenticates key Not trusted Console config# sntp broadcast client enable Sntp broadcast client enableConsole config# sntp client poll timer Console config-if#sntp anycast client enable Sntp anycast client enableSntp client enable interface Syntax Sntp client enable No sntp client enable 101 Sntp unicast client enableConsole config# sntp unicast client enable Sntp server Console config# sntp unicast client pollSntp unicast client poll Syntax Sntp unicast client poll no sntp unicast client poll 103 Show clockSyntax Show clock detail Console# show clock 104 Console# show sntp configuration Show sntp configurationSyntax Show sntp configuration 105 Following example shows the status of the Sntp Show sntp statusSyntax Show sntp status 106 107 Clock Console# delete startup-config Configuration and Image FilesDelete startup-config Copy Understanding Invalid Combinations of Source and Destination 110 Copying image file from a Server to Flash Memory Storing the Running or Startup Configuration on a ServerCopy Character Descriptions 111 Console# boot system image-1 Boot systemSyntax Boot system image-1 image-2 112 Sort type defaults to interface if unspecified Show running-configSyntax Show running-config sort type 113 Syntax Show startup-config sort type 114 Show startup-configConsole# show running-config no spanning-tree 115 Syntax Show backup-config 116 Show backup-configConsole# show startup-config no spanning-tree Console# show backup-config software version 117 Console# show bootvar Show bootvarSyntax Show bootvar Default Configuration 118 Interface range ethernet Ethernet Configuration CommandsInterface ethernet Following example disables port g5 Syntax Shutdown No shutdown Default ConfigurationInterface is enabled Shutdown Syntax Description string No description DescriptionSpeed Syntax Speed 100 1000 No speed 122 DuplexSyntax Duplex half full No duplex Negotiation Consoleconfig# interface ethernet g5Syntax Negotiation No negotiation Default Configuration Flowcontrol Syntax Mdix on auto No mdix MdixSyntax Flowcontrol auto on off No flowcontrol 124 125 Syntax Back-pressure No back-pressure Default ConfigurationBack-pressure 126 Port jumbo-frameClear counters Console# clear counters ethernet g1 Show interfaces configurationSet interface active Console# set interface active ethernet g5 Interfaces configuration 128 Show interfaces status 129 130 Console# show interfaces status Show interfaces description 131 132 Show interfaces countersConsole# show interfaces description ethernet g1 133 Console# show interfaces counters Following table describes the fields shown in the display Following example displays counters for port g1Console# show interfaces counters ethernet g1 134 135 Ieee Std .3, 2000 Edition, section 136 Syntax Show ports jumbo-frame Default ConfigurationShow ports jumbo-frame Port storm-control include-multicast Port storm-control broadcast enableConsoleconfig# port storm-control include-multicast Console# show ports jumbo-frame Default storm control broadcast rate is Broadcast storm control is disabledConsoleconfig-if#port storm-control broadcast enable Port storm-control broadcast rate Show ports storm-control Consoleconfig-if#port storm-control broadcast rateFollowing example displays the storm control configuration Syntax Show ports storm-control interface 140 Gvrp enable interface Gvrp CommandsGvrp enable global Syntax Gvrp enable No gvrp enable Default Configuration 142 Garp timerFollowing example enables Gvrp on ethernet g8 143 By default, dynamic Vlan creation is enabledGvrp vlan-creation-forbid Gvrp registration-forbid Console config-if#gvrp vlan-creation-forbidConsole config-if#gvrp registration-forbid Clear gvrp statistics 145 Show gvrp configurationConsole# clear gvrp statistics ethernet g8 146 Console# show gvrp configurationShow gvrp statistics 147 Show gvrp error-statisticsFollowing example shows Gvrp statistics information Console# show gvrp statistics 148 Console# show gvrp-error statisticsFollowing example displays Gvrp statistics information Ip igmp snooping Interface Igmp Snooping CommandsIp igmp snooping Global 149 150 Ip igmp snooping mrouterIp igmp snooping host-time-out 151 Console config-if#ip igmp snooping host-time-outIp igmp snooping mrouter-time-out Console config-if#ip igmp snooping leave-time-out Console config-if#ip igmp snooping mrouter-time-outDefault leave-time-out configuration is 10 seconds Ip igmp snooping leave-time-out Console # show ip igmp snooping mrouter Show ip igmp snooping mrouterShow ip igmp snooping interface Console # show ip igmp snooping interface Show ip igmp snooping groupsExample displays Igmp snooping information 154 155 Example shows Igmp snooping informationConsole # show ip igmp snooping groups Igmp Snooping Commands Ip address IP Addressing CommandsClear host dhcp Console# clear host dhcp No IP address is defined for interfaces Interface configuration Ethernet, VLAN, port-channelIp address dhcp 158 No default gateway is defined Ip default-gatewaySyntax Ip default-gateway ip-address No ip default-gateway 159 160 Following example defines an ip default gatewayShow ip interface 161 ArpConsole# show ip interface Clear arp-cache Arp timeoutConsole config# arp 198.133.219.232 00000c400fbc ethernet Console# clear arp-cache Syntax Show arp Default ConfigurationShow arp Following example displays entries in the ARP table Syntax Ip domain-lookup No ip domain-lookup Ip domain-lookupIp domain-name Syntax Ip domain-name name No ip domain-name No name server addresses are specified Ip name-serverIp host Following example sets the available name server No host is defined Clear hostSyntax Ip host name address No ip host name Syntax Clear host name Syntax Show hosts name Default Configuration Command ModeShow hosts 167 168 Lacp port-priority Lacp CommandsLacp system-priority Syntax Lacp port-priority value No lacp port-priority Default port timeout value is long Lacp timeoutSyntax Lacp timeout long short No lacp timeout 170 Console# show lacp ethernet g1 statistics Show lacp ethernetShow lacp port-channel Syntax Show lacp port-channel portchannelnumber Console# show lacp port-channel 172 Syntax Line console telnet ssh Line CommandsLine Syntax Speed bps Autobaud Exec-timeoutSyntax Autobaud No autobaud Default Configuration 174 Syntax Show line console telnet ssh Syntax Exec-timeout minutes seconds No exec-timeoutShow line 175 Terminal history size Following example displays the line configurationTerminal history Console# show line console Maximum for the sum of all buffers is 177 Line Commands Lldp enable interface Lldp CommandsLldp enable global Syntax Syntax Lldp timer seconds No lldp timer Lldp timerInterface configuration Ethernet Default 30 seconds Lldp hold-multiplier Lldp reinit-delayDefault Configuraiton Syntax Lldp hold-multiplier number No lldp hold-multiplier Syntax Lldp tx-delay seconds No lldp tx-delay Parameters Lldp tx-delaySyntax Lldp reinit-delay seconds No lldp reinit-delay Default value is 2 seconds Usage Guidelines Lldp optional-tlvLldp management-address No optional TLV is transmitted Clear lldp rx 184 Switch# show lldp configuration Show lldp configurationSyntax Show lldp configuration ethernet interface Show lldp local Show lldp neighbors 186 187 Switch# show lldp neighborsSwitch# show lldp neighbors ethernet g1 Lldp Commands Management ACL Management access-listName-The access list name using up to 32 characters 189 190 Console config# management access-class mlistPermit management 191 Management Access-list Configuration modeDeny management Management access-class 192 Syntax Show management access-list name Show management access-listShow management access-class Console# show management access-list 194 Syntax Show management access-class Default ConfigurationConsole# show management access-class Show copper-ports tdr PHY Diagnostics CommandsTest copper-port tdr Console# test copper-port tdr g3 Port must be active and working in 1000M Show copper-ports cable-lengthSyntax Show copper-ports cable-length interface 196 197 Show fiber-ports optical-transceiverConsole# show copper-ports cable-length 198 Console# show fiber-ports optical-transceiver 199 Console# show fiber-ports optical-transceiver detailed PHY Diagnostics Commands Interface port-channel Port Channel CommandsConsole config# interface port-channel Interface range port-channel Port is not assigned to any port-channel Console config# interface range port-channelChannel-group 202 Show interfaces port-channel Console config-if#channel-group 1 mode onPort channel load balance Syntax Show interfaces port-channel port-channel-number 204 Interface Configuration mode Port Monitor CommandsDefault is both rx and tx Port monitor 206 Syntax Show ports monitor Default ConfigurationShow ports monitor Console# show ports monitor 207 Port Monitor Commands Show qos QoS CommandsQos 210 Following example displays a QoS modeWrr-queue cos-map Following example maps CoS 3 to queue Interface Configuration Ethernet, port channel modeWrr-queue bandwidth 211 All queues are expedite queues Following example assigns WRR weights to egress queuesPriority-queue out num-of-queues 212 Following example sets queue 4, 3 to be expedite queues Console config# priority-queue out num-of-queuesShow qos interface 213 214 Qos map dscp-queueConsole# show qos interface ethernet g1 queuing 215 Qos trust GlobalSyntax Qos trust cos dscp No qos trust Qos trust Interface Syntax Qos trust No qos trust Default ConfigurationSyntax Qos cos default-cos No qos cos 216 Qos cos 217 Show qos mapSyntax Show qos map dscp-queue Following table describes the fields used above Following example displays the Dscp port-queue mapConsole# show qos map Dscp-queue map D1 x 10 + D2 = Value of Dscp Radius-server host Radius CommandsBy default, no Radius host is specified Ip-address-IP address of the Radius server host Radius-server key TimeoutDefault is an empty string Syntax Radius-server key key-string No radius-server key Radius-server source-ip Console config# radius-server retransmitRadius-server retransmit 221 222 Radius-server timeoutConsole config# radius-server timeout Radius-server deadtime Console config# radius-server deadtimeSyntax Show radius-servers Default Configuration Show radius-servers Console# show radius-servers Following example displays the Radius server settings224 Console# show rmon statistics ethernet g1 Rmon CommandsShow rmon statistics 225 226 Field Description Rmon collection history 227 Following example displays all Rmon group statistics Console config-if#rmon collection history 1 intervalShow rmon collection history Console# show rmon collection history Show rmon history 229 Console# show rmon history 5 throughput Console# show rmon history 5 errors230 Console# show rmon history 5 other 231 Rmon alarm 232 Show rmon alarm-table 233 Console# show rmon alarm-table Show rmon alarmSyntax Show rmon alarm-table Default Configuration Syntax Show rmon alarm number 235 Following example displays Rmon 1 alarmsConsole# show rmon alarm Rmon event 236 Show rmon events Following example configures an event with the trap indexSyntax Show rmon events Default Configuration Following example displays the Rmon event table Syntax Show rmon log event Show rmon logConsole# show rmon events Event-Event index. Range 0 239 Following example displays the Rmon logging tableConsole# show rmon log History table size is Log table size is Console config# rmon table-size historyRmon table-size 240 Snmp-server community Snmp CommandsThere are no default communities defined No snmp-server community community ip-address Snmp-server view Default SettingDefault and DefaultSuper views exists 242 243 Snmp-server filterProduct specific Included Snmp-server contactSnmp-server location Syntax Snmp-server contact text No snmp-server contact Syntax Snmp-server location text No snmp-server location Snmp-server enable trapsConsole config# snmp-server enable traps 245 Snmp-server host Snmp-server trap authenticationConsole config# snmp-server trap authentication 246 Snmp-server set 247 Snmp-server group 248 No group entry exists Console config# snmp-server group user-groupv3 priv readSnmp-server user Router context is translated to context in the MIB 250 Snmp-server v3-host Following example configures a new Snmp Version 3 userConsole config# snmp-server user 251 252 Following example configures an SNMPv3 hostSnmp-server engineID local Show snmp engineid Syntax Show snmp engineID Default SettingConsoleconfig # snmp-server engineID local default 253 Console# sh snmp Syntax Show snmp Default ConfigurationShow snmp 254 255 Show snmp viewsSyntax Show snmp views viewname 256 Show snmp groupsSyntax Show snmp groups groupname 257 Show snmp filtersSyntax Show snmp filters filtername 258 Show snmp usersSyntax Show snmp users username 259 Snmp Commands Syntax Spanning-tree No spanning-tree Default Configuration Spanning-Tree CommandsSpanning-tree mode Spanning-tree Spanning-tree forward-time Consoleconfig# spanning-tree mode rstpConsoleconfig# spanning-tree forward-time Seconds-Time in seconds. Range 4 Spanning-tree hello-time 263 264 Consoleconfig# spanning-tree hello-timeSpanning-tree max-age Consoleconfig# spanning-tree priority Spanning-tree disableConsoleconfig# spanning-tree max-age Spanning-tree priority Syntax Spanning-tree cost cost No spanning-tree cost Following example disables spanning-tree on g5Spanning-tree cost Cost-The port path cost Range 1 200,000,000 Spanning-tree portfast Consoleconfig-if#spanning-tree port-prioritySpanning-tree port-priority 267 Spanning-tree link-type Consoleconfig-if#spanning-tree portfastConsoleconfig-if#spanning-tree link-type shared 268 Spanning-tree mst priority Default number of hops isConsole config # spanning-tree mst 1 priority Spanning-tree mst max-hops Spanning-tree mst port-priority Console config # spanning-tree mst max-hopsConsoleconfig-if#spanning-tree mst 1 port-priority 270 Interface Long Short Spanning-tree mst configurationSpanning-tree mst cost 271 Syntax Instance instance-id add remove vlan vlan-range Syntax Spanning-tree mst configuration Default SettingInstance mst 272 Syntax Name string Name mstRevision mst Syntax Revision value No revision Show mst Default configuration revision number isFollowing example sets the configuration revision to Syntax Show current pending Exit mst Syntax Exit Default SettingSyntax Abort Default Setting Abort mst Console# spanning-tree pathcost method long Spanning-tree pathcost methodSpanning-tree bpdu 276 Syntax Spanning-tree bpdu filtering flooding Consoleconfig# spanning-tree bpdu floodingClear spanning-tree detected-protocols 277 Following example displays spanning-tree information Show spanning-treeConsole# clear spanning-tree detected-protocols ethernet g1 278 279 Console# show spanning-tree 280 281 282 283 284 285 Console# show spanning-tree mst-configuration 286 287 288 289 Spanning-tree mst mstp-rstp 290 Interface configuration Ethernet, port-channel Consoleconfig# spanning-tree mst mstp-rstpRoot guard is disabled Spanning-tree guard root 292 Following example enable root guard on port g8Consoleconfig-if#spanning-tree guard root Ip ssh server SSH CommandsIp ssh port Crypto key generate dsa Syntax Crypto key generate dsa Default ConfigurationConsole config# crypto key generate dsa Crypto key generate rsa Ip ssh pubkey-auth Syntax Crypto key generate rsa Default ConfigurationConsole config# crypto key generate rsa 295 User-key Consoleconfig# crypto key pubkey-chain sshCrypto key pubkey-chain ssh 297 Key-stringSyntax Key-string row key-string 298 Syntax Show ip ssh Default ConfigurationShow ip ssh Syntax Show crypto key mypubkey rsa dsa Following example displays the SSH server configurationShow crypto key mypubkey Rsa-RSA key Dsa-DSA key Console# show crypto key mypubkey rsa Show crypto key pubkey-chain ssh300 Console# show crypto key pubkey-chain ssh username bob Console# show crypto key pubkey-chain sshFollowing example displays the SSH public called bob 301 SSH Commands Logging on Syslog CommandsSyntax Logging on no logging on Default Configuration Logging As described in the field descriptions Default is informationalLogging console Syntax Logging console level No logging console Logging buffered size Default level is informationalLogging buffered Syntax Logging buffered level No logging buffered Clear logging Console config# logging buffered sizeSyntax Clear logging Default Configuration Console# clear logging Clear logging file Syntax Clear logging file Default ConfigurationLogging file Syntax Logging file level No logging file Following example clears messages from the logging file Syntax Show logging Default ConfigurationShow logging Console# clear logging file Console# show logging Syntax Show logging file Default ConfigurationShow logging file 309 310 Syntax Show syslog-servers Default ConfigurationShow syslog-servers 311 Following example displays the syslog server settingsConsole# show syslog-servers Syslog Commands Ping Timeout timeout-The default is 2000 millisecondsSystem Management 313 314 TracerouteFollowing example displays a ping to IP address 315 316 317 Special Telnet Command charactersTelnet Keywords Table 318 Ports Table 319 Syntax Resume connection Following command switches to another open Telnet sessionResume 320 Reload Hostname Console# show users Show usersShow sessions Console show sessions Exec modeShow system Syntax Show system Syntax Show version 324 Show versionFollowing example displays the system information Console show system Tag-The device asset tag. Range 1- 16 characters Asset-tagSyntax Asset-tag tag No asset-tag 325 Console show system id Syntax Show system id Default ConfigurationShow system id 326 No Tacacs host is specified Tacacs CommandsTacacs-server host 327 Tacacs-server key Tacacs-server timeoutFollowing example sets the authentication encryption key Following example specifies a TACACS+ host 329 Console config# tacacs-server timeoutTacacs-server source-ip Ip-address-Name or IP address of the host Show tacacsSyntax Show tacacs ip-address Console# show tacacs User Interface EnableDisable Syntax Login Default Configuration LoginConfigure Syntax Configure All command modes ExitconfigurationSyntax Exit Default Configuration 333 End Syntax End Default ConfigurationExitEXEC Following example closes an active terminal session Help Syntax Help Default ConfigurationSyntax History No history Default Configuration History History size Syntax History size number-of-commands No history sizeSyntax Debug-mode Default Configuration Debug-mode 337 Syntax Show history Default ConfigurationShow history Console# show history Syntax Show privilege Default ConfigurationShow privilege Console# show privilege Vlan Vlan CommandsVlan database Console# vlan database Default-vlan disableInterface vlan 341 Interface range vlanSyntax Interface range vlan vlan-range all Syntax Name string no name Switchport access vlanName 342 343 Switchport trunk allowed vlanConsole config-if#switchport access vlan Console config-if#switchport trunk allowed vlan add 2,5-8 Switchport trunk native vlanSwitchport general allowed vlan Console config-if#switchport trunk native vlan Switchport general pvid 345 346 Switchport general ingress-filtering disableIngress filtering is enabled All frame types are accepted at ingress Switchport general acceptable-frame-type tagged-onlySwitchport forbidden vlan All VLANs allowed Following example maps protocol ip-arp to the group named Console config-if#switchport forbidden vlan addMap protocol protocols-group 348 Vlan-id-VLAN ID of the internal usage VLAN.Range Valid Vlan Switchport general map protocols-group vlanIp internal-usage-vlan 349 Syntax Show vlan tag vlan-id name vlan-name Console config# ip internal-usage-vlanShow vlan Following example displays all Vlan information 351 Syntax Show vlan internal usage Default ConfigurationShow vlan internal usage Console# show vlan internal usage Syntax Show vlan protocols-groups Default ConfigurationShow vlan protocols-groups Following example displays protocols-groups information 353 Show interfaces switchportConsole# show vlan protocols-groups Syntax Switchport mode customer access trunk general 354 Switchport modeConsole# show interface switchport ethernet g1 No Vlan is configured Switchport customer vlanNo switchport mode Vlan-id- Vlan ID of the customer 356 Ip http port Web ServerIp http server Syntax Ip http port port-number No ip http port Ip https port Default for the device is disabledIp https server Syntax Ip https port port-number No ip https port 359 Following example configures the https port number toCrypto certificate generate Certificate and the SSL RSA key pairs do not exist Console enable# crypto certificate generate key-generateCrypto certificate request Following example regenerates a Https certificate Console# crypto certificate 1 request 361 Number-Specifies the certificate number. Range 1 Crypto certificate importSyntax Crypto certificate number import 362 Certificate number Consoleconfig# crypto certificate 1 importIp https certificate 363 Syntax Crypto certificate number export pkcs12 Console config# ip https certificateCrypto certificate export pkcs12 364 Console# crypto certificate 1 export pkcs12 Following example exports the certificate and RSA keys365 Following example imports the certificate and RSA keys Crypto certificate import pkcs12Syntax Crypto certificate number import pkcs12 passphrase 366 367 Following example displays the certificate Show crypto certificate mycertificateSyntax Show crypto certificate mycertificate number Console# show crypto certificate mycertificate Console# show ip http Show ip httpShow ip https Console# show ip https 370 Console config# aaa authentication dot1x default none 802.1x CommandsAaa authentication dot1x Method1 method2...-At least one from the following table Dot1x system-auto-control Following example enables 802.1x globallyConsole config# dot1x system-auto-control Dot1x port-control Syntax Dot1x re-authentication No dot1x re-authentication Dot1x re-authenticationConsole config-if#dot1x port-control auto 373 Console config-if#dot1x re-authentication Dot1x timeout re-authperiodDot1x re-authenticate Console config-if#dot1x timeout re-authperiod 375 Dot1x timeout quiet-periodConsole# dot1x re-authenticate ethernet g8 376 Dot1x timeout tx-periodConsole config-if#dot1x timeout quiet-period Syntax Dot1x max-req count No dot1x max-req Dot1x timeout supp-timeoutDot1x max-req 377 Dot1x timeout server-timeout 378 Syntax Show dot1x ethernet interface Console config# dot1x timeout server-timeoutShow dot1x 379 380 Console# show dot1x ethernet g3 Username-Supplicant username Range 1- 160 characters Show dot1x usersSyntax Show dot1x users username username Following example displays 802.1X users 382 Show dot1x statisticsSyntax Show dot1x statistics ethernet interface Switch# show dot1x statistics ethernet g1 383 Syntax Dot1x auth-not-req no dot1x auth-not-req User should be authorized to access the VlanDot1x auth-not-req 384 Syntax Dot1x multiple-hosts no dot1x multiple-hosts Dot1x multiple-hostsDot1x single-host-violation 385 Syntax Show dot1x advanced ethernet interface Show dot1x advancedForward trap 386 387 Switch# show dot1x advancedSwitch# show dot1x advanced ethernet g1 Console# show dot1x advanced ethernet g1 388

Dell 5324 manual Following example displays counters for port g1, 134

Models: 5324

w w w . d e l l . c o m s u p p o r t . d e l l . c o m

The following example displays counters for port g1.

Console# show interfaces counters ethernet g1

The following table describes the fields shown in the display:

134

5324 specifications