Manuals / Dell / Computer Equipment / Switch

Dell 5324 manual Gvrp registration-forbid, Clear gvrp statistics, 144

Models: 5324

1 388

Download 388 pages 31.83 Kb

Page 144

Image 144

w w w . d e l l . c o m s u p p o r t . d e l l . c o m

Example

The following example disables dynamic VLAN creation on port g8.

Console (config)# interface ethernet g8

Console (config-if)#gvrp vlan-creation-forbid

gvrp registration-forbid

The gvrp registration-forbidInterface Configuration mode command de-registers all dynamic VLANs, and prevents dynamic VLAN registration on the port. To allow dynamic registering for VLANs on a port, use the no form of this command.

Syntax

gvrp registration-forbid no gvrp registration-forbid

Default Configuration

Dynamic registering and deregistering for each VLAN on the port is allowed.

Command Mode

Interface Configuration (Ethernet, port-channel) mode

User Guidelines

•There are no user guidelines for this command.

Example

The following example shows how default dynamic registering and deregistering is forbidden for each VLAN on port g8.

Console (config)# interface ethernet g8

Console (config-if)#gvrp registration-forbid

clear gvrp statistics

The clear gvrp statistics Privileged EXEC mode command clears all the GVRP statistics information.

Syntax

clear gvrp statistics [ethernet interface port-channel port-channel-number]

•interface—A valid Ethernet interface.

•port-channel-number—A valid port-channel trunk index.

144

GVRP Commands

Page 144

Image 144

Dell 5324 manual Gvrp registration-forbid, Clear gvrp statistics, Console config-if#gvrp vlan-creation-forbid, 144

Contents

CLI Reference Guide Aug Contents Using the CLI Address Table Commands Clock Ethernet Configuration Commands Igmp Snooping Commands Lacp Commands Management ACL Port Monitor Commands Rmon Commands Spanning-Tree Commands SSH Commands Syslog Commands Tacacs Commands Vlan Commands 32 802.1x Commands 382 Page Command Groups Command GroupsIntroduction Configures and reports on Spanning Tree protocol Configures Tacacs commandsConfigures commands related to 802.1x security protocol AAA Commands Address Table CommandsConfigures an external time source for Configures the system to automatically switchDefines an authentication key for Simple Displays statically created entries in the bridgeConfiguration and Image Files Commands Ethernet Configuration Commands Displays the backup configuration file contentsGvrp Commands Igmp Snooping Commands Defines a default gateway routerIP Addressing Sets an IP addressLine Commands Deletes entries from the host name-to-addressCache Lldp Commands Sets the line for automatic baud rate detectionManagement ACL Commands PHY Diagnostics CommandsPort Channel Commands Port Monitor CommandsQoS Commands Radius Commands Enables each port trust stateRmon Commands Snmp CommandsSpanning Tree Commands MST SSH Commands Overrides the default link-type settingSets the default path cost method Syslog Commands System Management Commands Tacacs CommandsReloads the operating system User Interface Commands Vlan CommandsSwitches the mode to debug Disables the default Vlan functionalityReserves a Vlan as the internal usage Vlan of an InterfaceWeb Server Commands 802.1x Commands Command Description Access ModeCommand Groups Command Modes GC Global Configuration ModeDevice Notification operation IC Interface Configuration Mode SntpAn Extensible Authentication Protocol EAP request/identity Frame, from the client, before resending the requestReserves a Vlan as the internal usage Vlan of an interface LC Line Configuration Mode Enables the Simple Network Time Protocol Sntp client on anCommand Description MA Management Access-level Mode PE Privileged User Exec ModeVlan SP SSH Public Key Mode UE User Exec ModeCommand Modes VC Vlan Configuration Mode W . d e l l . c o m s u p p o r t . d e l l . c o m Using the CLI CLI Command ModesIntroduction User Exec Mode Privileged Exec ModeGlobal Configuration Mode Exit End Ctrl+ZStarting the CLI Editing Features Entering CommandsConsoleconfig# username admin password smith Terminal Command Buffer Negating the Effect of CommandsCommand Completion Config#interface ethernetCLI Command Conventions Keyboard ShortcutsItalic font EnterUsing the CLI AAA Commands Aaa authentication loginDefault Configuration Command ModeAaa authentication enable Following example configures authentication loginExample Login authentication Console config# aaa authentication enable default enableEnable authentication Console config-line#login authentication defaultIp http authentication Console config-line#enable authentication defaultFollowing example configures the http authentication Ip https authentication Show authentication methodsFollowing example configures https authentication Syntax Show authentication methods Default Configuration This command has no default configurationPrivileged Exec mode Following example displays the authentication configurationPassword Console# show authentication methodsSyntax Password password encrypted No password Enable password No password is requiredFollowing example specifies a password secret on a line Username Show users accountsNo user is defined Syntax Show users accounts Default Configuration Console# show users accountsAAA Commands Address Table Commands Interface configuration Vlan modeBridge address Disabled. All multicast addresses are flooded to all ports This example, bridge multicast filtering is enabledConsole config# bridge multicast filtering Bridge multicast filteringNo multicast addresses are defined ExamplesFollowing example registers the MAC address Command Modes Bridge multicast forbidden addressNo forbidden addresses are defined Disable forward-all on the specified interface Bridge multicast forward-allBridge multicast forbidden forward-all This example all multicast packets on port g8 are forwardedBridge aging-time SyntaxClear bridge Syntax Clear bridgeConsole# clear bridge Disabled No port security Interface Configuration Ethernet, port-channel modePort security Console config-if#port security routed secure-address Port security routed secure-addressShow bridge address-table Mac-address-Specify a MAC address in the formatPort-channel-number-A valid port-channel number Show bridge address-table static Console# show bridge address-tableShow bridge address-table count Console# show bridge address-table staticSyntax Show bridge address-table count vlan vlan Vlan -Specific VlanShow bridge multicast address-table Console# show bridge address-table countConsole # show bridge multicast address-table Console # show bridge multicast address-table format ipShow bridge multicast filtering Show ports securitySyntax Show bridge multicast filtering vlan-id Vlanid-A valid Vlan ID valueConsole # show ports security Clock Clock setClock source Syntax Clock source sntp No clock sourceClock timezone No external clock sourceConsole# clock source sntp Clock summer-time Sntp authentication-key No authentication key is definedSntp authenticate Consoleconfig# sntp authentication-key 8 md5 ClkKeySyntax Sntp authenticate No sntp authenticate Sntp client poll timer Following example authenticates keySntp trusted-key Not trustedSntp broadcast client enable Console config# sntp client poll timerConsole config# sntp broadcast client enable Sntp anycast client enable Sntp client enable interfaceConsole config-if#sntp anycast client enable Syntax Sntp client enable No sntp client enableSntp unicast client enable Console config# sntp unicast client enable101 Console config# sntp unicast client poll Sntp unicast client pollSntp server Syntax Sntp unicast client poll no sntp unicast client pollShow clock Syntax Show clock detail103 Console# show clock 104Show sntp configuration Syntax Show sntp configurationConsole# show sntp configuration 105Show sntp status Syntax Show sntp statusFollowing example shows the status of the Sntp 106107 Clock Configuration and Image Files Delete startup-configConsole# delete startup-config CopyUnderstanding Invalid Combinations of Source and Destination 110Storing the Running or Startup Configuration on a Server Copy Character DescriptionsCopying image file from a Server to Flash Memory 111Boot system Syntax Boot system image-1 image-2Console# boot system image-1 112Show running-config Syntax Show running-config sort typeSort type defaults to interface if unspecified 113Show startup-config Console# show running-config no spanning-treeSyntax Show startup-config sort type 114 115 Show backup-config Console# show startup-config no spanning-treeSyntax Show backup-config 116 Console# show backup-config software version 117Show bootvar Syntax Show bootvar Default ConfigurationConsole# show bootvar 118Ethernet Configuration Commands Interface ethernetInterface range ethernet Syntax Shutdown No shutdown Default Configuration Interface is enabledFollowing example disables port g5 ShutdownDescription SpeedSyntax Description string No description Syntax Speed 100 1000 No speedDuplex Syntax Duplex half full No duplex122 Consoleconfig# interface ethernet g5 Syntax Negotiation No negotiation Default ConfigurationNegotiation FlowcontrolMdix Syntax Flowcontrol auto on off No flowcontrolSyntax Mdix on auto No mdix 124Syntax Back-pressure No back-pressure Default Configuration Back-pressure125 Port jumbo-frame Clear counters126 Show interfaces configuration Set interface activeConsole# clear counters ethernet g1 Console# set interface active ethernet g5Interfaces configuration 128Show interfaces status 129130 Console# show interfaces statusShow interfaces description 131Show interfaces counters Console# show interfaces description ethernet g1132 133 Console# show interfaces countersFollowing example displays counters for port g1 Console# show interfaces counters ethernet g1Following table describes the fields shown in the display 134135 Ieee Std .3, 2000 Edition, sectionSyntax Show ports jumbo-frame Default Configuration Show ports jumbo-frame136 Port storm-control broadcast enable Consoleconfig# port storm-control include-multicastPort storm-control include-multicast Console# show ports jumbo-frameBroadcast storm control is disabled Consoleconfig-if#port storm-control broadcast enableDefault storm control broadcast rate is Port storm-control broadcast rateConsoleconfig-if#port storm-control broadcast rate Following example displays the storm control configurationShow ports storm-control Syntax Show ports storm-control interface140 Gvrp Commands Gvrp enable globalGvrp enable interface Syntax Gvrp enable No gvrp enable Default ConfigurationGarp timer Following example enables Gvrp on ethernet g8142 By default, dynamic Vlan creation is enabled Gvrp vlan-creation-forbid143 Console config-if#gvrp vlan-creation-forbid Console config-if#gvrp registration-forbidGvrp registration-forbid Clear gvrp statisticsShow gvrp configuration Console# clear gvrp statistics ethernet g8145 Console# show gvrp configuration Show gvrp statistics146 Show gvrp error-statistics Following example shows Gvrp statistics information147 Console# show gvrp statisticsConsole# show gvrp-error statistics Following example displays Gvrp statistics information148 Igmp Snooping Commands Ip igmp snooping GlobalIp igmp snooping Interface 149Ip igmp snooping mrouter Ip igmp snooping host-time-out150 Console config-if#ip igmp snooping host-time-out Ip igmp snooping mrouter-time-out151 Console config-if#ip igmp snooping mrouter-time-out Default leave-time-out configuration is 10 secondsConsole config-if#ip igmp snooping leave-time-out Ip igmp snooping leave-time-outShow ip igmp snooping mrouter Show ip igmp snooping interfaceConsole # show ip igmp snooping mrouter Show ip igmp snooping groups Example displays Igmp snooping informationConsole # show ip igmp snooping interface 154Example shows Igmp snooping information Console # show ip igmp snooping groups155 Igmp Snooping Commands IP Addressing Commands Clear host dhcpIp address Console# clear host dhcpInterface configuration Ethernet, VLAN, port-channel Ip address dhcpNo IP address is defined for interfaces 158Ip default-gateway Syntax Ip default-gateway ip-address No ip default-gatewayNo default gateway is defined 159Following example defines an ip default gateway Show ip interface160 Arp Console# show ip interface161 Arp timeout Console config# arp 198.133.219.232 00000c400fbc ethernetClear arp-cache Syntax Show arp Default Configuration Show arpConsole# clear arp-cache Following example displays entries in the ARP tableIp domain-lookup Ip domain-nameSyntax Ip domain-lookup No ip domain-lookup Syntax Ip domain-name name No ip domain-nameIp name-server Ip hostNo name server addresses are specified Following example sets the available name serverClear host Syntax Ip host name address No ip host nameNo host is defined Syntax Clear host nameDefault Configuration Command Mode Show hostsSyntax Show hosts name 167168 Lacp Commands Lacp system-priorityLacp port-priority Syntax Lacp port-priority value No lacp port-priorityLacp timeout Syntax Lacp timeout long short No lacp timeoutDefault port timeout value is long 170Show lacp ethernet Show lacp port-channelConsole# show lacp ethernet g1 statistics Syntax Show lacp port-channel portchannelnumberConsole# show lacp port-channel 172Line Commands LineSyntax Line console telnet ssh Syntax Speed bpsExec-timeout Syntax Autobaud No autobaud Default ConfigurationAutobaud 174Syntax Exec-timeout minutes seconds No exec-timeout Show lineSyntax Show line console telnet ssh 175Following example displays the line configuration Terminal historyTerminal history size Console# show line consoleMaximum for the sum of all buffers is 177Line Commands Lldp Commands Lldp enable globalLldp enable interface SyntaxLldp timer Interface configuration EthernetSyntax Lldp timer seconds No lldp timer Default 30 secondsLldp reinit-delay Default ConfiguraitonLldp hold-multiplier Syntax Lldp hold-multiplier number No lldp hold-multiplierLldp tx-delay Syntax Lldp reinit-delay seconds No lldp reinit-delaySyntax Lldp tx-delay seconds No lldp tx-delay Parameters Default value is 2 secondsLldp optional-tlv Lldp management-addressUsage Guidelines No optional TLV is transmittedClear lldp rx 184Show lldp configuration Syntax Show lldp configuration ethernet interfaceSwitch# show lldp configuration Show lldp localShow lldp neighbors 186Switch# show lldp neighbors Switch# show lldp neighbors ethernet g1187 Lldp Commands Management access-list Name-The access list name using up to 32 charactersManagement ACL 189Console config# management access-class mlist Permit management190 Management Access-list Configuration mode Deny management191 Management access-class 192Show management access-list Show management access-classSyntax Show management access-list name Console# show management access-listSyntax Show management access-class Default Configuration Console# show management access-class194 PHY Diagnostics Commands Test copper-port tdrShow copper-ports tdr Console# test copper-port tdr g3Show copper-ports cable-length Syntax Show copper-ports cable-length interfacePort must be active and working in 1000M 196Show fiber-ports optical-transceiver Console# show copper-ports cable-length197 198 Console# show fiber-ports optical-transceiver199 Console# show fiber-ports optical-transceiver detailedPHY Diagnostics Commands Port Channel Commands Console config# interface port-channelInterface port-channel Interface range port-channelConsole config# interface range port-channel Channel-groupPort is not assigned to any port-channel 202Console config-if#channel-group 1 mode on Port channel load balanceShow interfaces port-channel Syntax Show interfaces port-channel port-channel-number204 Port Monitor Commands Default is both rx and txInterface Configuration mode Port monitorSyntax Show ports monitor Default Configuration Show ports monitor206 Console# show ports monitor 207Port Monitor Commands QoS Commands QosShow qos Following example displays a QoS mode Wrr-queue cos-map210 Interface Configuration Ethernet, port channel mode Wrr-queue bandwidthFollowing example maps CoS 3 to queue 211Following example assigns WRR weights to egress queues Priority-queue out num-of-queuesAll queues are expedite queues 212Console config# priority-queue out num-of-queues Show qos interfaceFollowing example sets queue 4, 3 to be expedite queues 213Qos map dscp-queue Console# show qos interface ethernet g1 queuing214 Qos trust Global Syntax Qos trust cos dscp No qos trust215 Syntax Qos trust No qos trust Default Configuration Syntax Qos cos default-cos No qos cos 216Qos trust Interface Qos cosShow qos map Syntax Show qos map dscp-queue217 Following example displays the Dscp port-queue map Console# show qos map Dscp-queue mapFollowing table describes the fields used above D1 x 10 + D2 = Value of DscpRadius Commands By default, no Radius host is specifiedRadius-server host Ip-address-IP address of the Radius server hostTimeout Default is an empty stringRadius-server key Syntax Radius-server key key-string No radius-server keyConsole config# radius-server retransmit Radius-server retransmitRadius-server source-ip 221Radius-server timeout Console config# radius-server timeout222 Console config# radius-server deadtime Syntax Show radius-servers Default ConfigurationRadius-server deadtime Show radius-serversFollowing example displays the Radius server settings 224Console# show radius-servers Rmon Commands Show rmon statisticsConsole# show rmon statistics ethernet g1 225226 Field DescriptionRmon collection history 227Console config-if#rmon collection history 1 interval Show rmon collection historyFollowing example displays all Rmon group statistics Console# show rmon collection historyShow rmon history 229Console# show rmon history 5 errors 230Console# show rmon history 5 throughput Console# show rmon history 5 other 231Rmon alarm 232Show rmon alarm-table 233Show rmon alarm Syntax Show rmon alarm-table Default ConfigurationConsole# show rmon alarm-table Syntax Show rmon alarm numberFollowing example displays Rmon 1 alarms Console# show rmon alarm235 Rmon event 236Following example configures an event with the trap index Syntax Show rmon events Default ConfigurationShow rmon events Following example displays the Rmon event tableShow rmon log Console# show rmon eventsSyntax Show rmon log event Event-Event index. Range 0Following example displays the Rmon logging table Console# show rmon log239 Console config# rmon table-size history Rmon table-sizeHistory table size is Log table size is 240Snmp Commands There are no default communities definedSnmp-server community No snmp-server community community ip-addressDefault Setting Default and DefaultSuper views existsSnmp-server view 242Snmp-server filter Product specific243 Snmp-server contact Snmp-server locationIncluded Syntax Snmp-server contact text No snmp-server contactSnmp-server enable traps Console config# snmp-server enable trapsSyntax Snmp-server location text No snmp-server location 245Snmp-server trap authentication Console config# snmp-server trap authenticationSnmp-server host 246Snmp-server set 247Snmp-server group 248Console config# snmp-server group user-groupv3 priv read Snmp-server userNo group entry exists Router context is translated to context in the MIB250 Following example configures a new Snmp Version 3 user Console config# snmp-server userSnmp-server v3-host 251Following example configures an SNMPv3 host Snmp-server engineID local252 Syntax Show snmp engineID Default Setting Consoleconfig # snmp-server engineID local defaultShow snmp engineid 253Syntax Show snmp Default Configuration Show snmpConsole# sh snmp 254Show snmp views Syntax Show snmp views viewname255 Show snmp groups Syntax Show snmp groups groupname256 Show snmp filters Syntax Show snmp filters filtername257 Show snmp users Syntax Show snmp users username258 259 Snmp Commands Spanning-Tree Commands Spanning-tree modeSyntax Spanning-tree No spanning-tree Default Configuration Spanning-treeConsoleconfig# spanning-tree mode rstp Consoleconfig# spanning-tree forward-timeSpanning-tree forward-time Seconds-Time in seconds. Range 4Spanning-tree hello-time 263Consoleconfig# spanning-tree hello-time Spanning-tree max-age264 Spanning-tree disable Consoleconfig# spanning-tree max-ageConsoleconfig# spanning-tree priority Spanning-tree priorityFollowing example disables spanning-tree on g5 Spanning-tree costSyntax Spanning-tree cost cost No spanning-tree cost Cost-The port path cost Range 1 200,000,000Consoleconfig-if#spanning-tree port-priority Spanning-tree port-prioritySpanning-tree portfast 267Consoleconfig-if#spanning-tree portfast Consoleconfig-if#spanning-tree link-type sharedSpanning-tree link-type 268Default number of hops is Console config # spanning-tree mst 1 prioritySpanning-tree mst priority Spanning-tree mst max-hopsConsole config # spanning-tree mst max-hops Consoleconfig-if#spanning-tree mst 1 port-prioritySpanning-tree mst port-priority 270Spanning-tree mst configuration Spanning-tree mst costInterface Long Short 271Syntax Spanning-tree mst configuration Default Setting Instance mstSyntax Instance instance-id add remove vlan vlan-range 272Name mst Revision mstSyntax Name string Syntax Revision value No revisionDefault configuration revision number is Following example sets the configuration revision toShow mst Syntax Show current pendingSyntax Exit Default Setting Syntax Abort Default SettingExit mst Abort mstSpanning-tree pathcost method Spanning-tree bpduConsole# spanning-tree pathcost method long 276Consoleconfig# spanning-tree bpdu flooding Clear spanning-tree detected-protocolsSyntax Spanning-tree bpdu filtering flooding 277Show spanning-tree Console# clear spanning-tree detected-protocols ethernet g1Following example displays spanning-tree information 278279 Console# show spanning-tree280 281 282 283 284 285 Console# show spanning-tree mst-configuration 286287 288 289 Spanning-tree mst mstp-rstp 290Consoleconfig# spanning-tree mst mstp-rstp Root guard is disabledInterface configuration Ethernet, port-channel Spanning-tree guard rootFollowing example enable root guard on port g8 Consoleconfig-if#spanning-tree guard root292 SSH Commands Ip ssh portIp ssh server Syntax Crypto key generate dsa Default Configuration Console config# crypto key generate dsaCrypto key generate dsa Crypto key generate rsaSyntax Crypto key generate rsa Default Configuration Console config# crypto key generate rsaIp ssh pubkey-auth 295Consoleconfig# crypto key pubkey-chain ssh Crypto key pubkey-chain sshUser-key Key-string Syntax Key-string row key-string297 Syntax Show ip ssh Default Configuration Show ip ssh298 Following example displays the SSH server configuration Show crypto key mypubkeySyntax Show crypto key mypubkey rsa dsa Rsa-RSA key Dsa-DSA keyShow crypto key pubkey-chain ssh 300Console# show crypto key mypubkey rsa Console# show crypto key pubkey-chain ssh Following example displays the SSH public called bobConsole# show crypto key pubkey-chain ssh username bob 301SSH Commands Syslog Commands Syntax Logging on no logging on Default ConfigurationLogging on LoggingDefault is informational Logging consoleAs described in the field descriptions Syntax Logging console level No logging consoleDefault level is informational Logging bufferedLogging buffered size Syntax Logging buffered level No logging bufferedConsole config# logging buffered size Syntax Clear logging Default ConfigurationClear logging Console# clear loggingSyntax Clear logging file Default Configuration Logging fileClear logging file Syntax Logging file level No logging fileSyntax Show logging Default Configuration Show loggingFollowing example clears messages from the logging file Console# clear logging fileSyntax Show logging file Default Configuration Show logging fileConsole# show logging 309Syntax Show syslog-servers Default Configuration Show syslog-servers310 Following example displays the syslog server settings Console# show syslog-servers311 Syslog Commands Timeout timeout-The default is 2000 milliseconds System ManagementPing 313Traceroute Following example displays a ping to IP address314 315 316 Special Telnet Command characters Telnet317 Keywords Table 318Ports Table 319Following command switches to another open Telnet session ResumeSyntax Resume connection 320Reload HostnameShow users Show sessionsConsole# show users Exec mode Show systemConsole show sessions Syntax Show systemShow version Following example displays the system informationSyntax Show version 324 Console show systemAsset-tag Syntax Asset-tag tag No asset-tagTag-The device asset tag. Range 1- 16 characters 325Syntax Show system id Default Configuration Show system idConsole show system id 326Tacacs Commands Tacacs-server hostNo Tacacs host is specified 327Tacacs-server timeout Following example sets the authentication encryption keyTacacs-server key Following example specifies a TACACS+ hostConsole config# tacacs-server timeout Tacacs-server source-ip329 Show tacacs Syntax Show tacacs ip-addressIp-address-Name or IP address of the host Console# show tacacsEnable DisableUser Interface Login ConfigureSyntax Login Default Configuration Syntax ConfigureExitconfiguration Syntax Exit Default ConfigurationAll command modes 333Syntax End Default Configuration ExitEXECEnd Following example closes an active terminal sessionSyntax Help Default Configuration Syntax History No history Default ConfigurationHelp HistorySyntax History size number-of-commands No history size Syntax Debug-mode Default ConfigurationHistory size Debug-modeSyntax Show history Default Configuration Show history337 Syntax Show privilege Default Configuration Show privilegeConsole# show history Console# show privilegeVlan Commands Vlan databaseVlan Default-vlan disable Interface vlanConsole# vlan database Interface range vlan Syntax Interface range vlan vlan-range all341 Switchport access vlan NameSyntax Name string no name 342Switchport trunk allowed vlan Console config-if#switchport access vlan343 Switchport trunk native vlan Switchport general allowed vlanConsole config-if#switchport trunk allowed vlan add 2,5-8 Console config-if#switchport trunk native vlanSwitchport general pvid 345Switchport general ingress-filtering disable Ingress filtering is enabled346 Switchport general acceptable-frame-type tagged-only Switchport forbidden vlanAll frame types are accepted at ingress All VLANs allowedConsole config-if#switchport forbidden vlan add Map protocol protocols-groupFollowing example maps protocol ip-arp to the group named 348Switchport general map protocols-group vlan Ip internal-usage-vlanVlan-id-VLAN ID of the internal usage VLAN.Range Valid Vlan 349Console config# ip internal-usage-vlan Show vlanSyntax Show vlan tag vlan-id name vlan-name Following example displays all Vlan informationSyntax Show vlan internal usage Default Configuration Show vlan internal usage351 Syntax Show vlan protocols-groups Default Configuration Show vlan protocols-groupsConsole# show vlan internal usage Following example displays protocols-groups informationShow interfaces switchport Console# show vlan protocols-groups353 Switchport mode Console# show interface switchport ethernet g1Syntax Switchport mode customer access trunk general 354 Switchport customer vlan No switchport modeNo Vlan is configured Vlan-id- Vlan ID of the customer356 Web Server Ip http serverIp http port Syntax Ip http port port-number No ip http portDefault for the device is disabled Ip https serverIp https port Syntax Ip https port port-number No ip https portFollowing example configures the https port number to Crypto certificate generate359 Console enable# crypto certificate generate key-generate Crypto certificate requestCertificate and the SSL RSA key pairs do not exist Following example regenerates a Https certificateConsole# crypto certificate 1 request 361Crypto certificate import Syntax Crypto certificate number importNumber-Specifies the certificate number. Range 1 362Consoleconfig# crypto certificate 1 import Ip https certificateCertificate number 363Console config# ip https certificate Crypto certificate export pkcs12Syntax Crypto certificate number export pkcs12 364Following example exports the certificate and RSA keys 365Console# crypto certificate 1 export pkcs12 Crypto certificate import pkcs12 Syntax Crypto certificate number import pkcs12 passphraseFollowing example imports the certificate and RSA keys 366367 Show crypto certificate mycertificate Syntax Show crypto certificate mycertificate numberFollowing example displays the certificate Console# show crypto certificate mycertificateShow ip http Show ip httpsConsole# show ip http Console# show ip https 370802.1x Commands Aaa authentication dot1xConsole config# aaa authentication dot1x default none Method1 method2...-At least one from the following tableFollowing example enables 802.1x globally Console config# dot1x system-auto-controlDot1x system-auto-control Dot1x port-controlDot1x re-authentication Console config-if#dot1x port-control autoSyntax Dot1x re-authentication No dot1x re-authentication 373Dot1x timeout re-authperiod Dot1x re-authenticateConsole config-if#dot1x re-authentication Console config-if#dot1x timeout re-authperiodDot1x timeout quiet-period Console# dot1x re-authenticate ethernet g8375 Dot1x timeout tx-period Console config-if#dot1x timeout quiet-period376 Dot1x timeout supp-timeout Dot1x max-reqSyntax Dot1x max-req count No dot1x max-req 377Dot1x timeout server-timeout 378Console config# dot1x timeout server-timeout Show dot1xSyntax Show dot1x ethernet interface 379380 Console# show dot1x ethernet g3Show dot1x users Syntax Show dot1x users username usernameUsername-Supplicant username Range 1- 160 characters Following example displays 802.1X usersShow dot1x statistics Syntax Show dot1x statistics ethernet interface382 Switch# show dot1x statistics ethernet g1 383User should be authorized to access the Vlan Dot1x auth-not-reqSyntax Dot1x auth-not-req no dot1x auth-not-req 384Dot1x multiple-hosts Dot1x single-host-violationSyntax Dot1x multiple-hosts no dot1x multiple-hosts 385Show dot1x advanced Forward trapSyntax Show dot1x advanced ethernet interface 386Switch# show dot1x advanced Switch# show dot1x advanced ethernet g1387 Console# show dot1x advanced ethernet g1 388