Check Burner Flame Flame Signal | Delta PG PLUS-25 specs

Maintenance Procedures

Check Burner Flame

Flame Signal

Inspect the burner flame through the obser- vation port on the burner mounting plate.

If flame pattern is not fully blue and covers the entire burner surface, shut the unit down and allow it to cool thoroughly.

Close the manual gas valve on the gas sup- ply line and disconnect the gas piping to remove the burner assembly from the unit.

Remove the burner head mounting screws and remove the burner head. Inspect the head for deterioration. Use compressed air or a vacuum to clean the burner head.

Remove the venturi and gas valve assem- bly from the blower.

Use the vacuum cleaner or compressed air to clean the interior of the blower assembly. Inspect the blower blades to ensure they are clean and not damage.

Re-assemble the venturi and gas valve onto the blower. Ensure the venturi gasket is in good condition and positioned correctly.

Re-assemble the burner head onto the mounting plate. Ensure the burner head gasket is in good condition and positioned correctly.

Re-assemble the gas supply connection and open the manual gas valve placing the unit back into service.

The flame signal should be at least 0.6∝ Α. Refer to the PERFORMANCE PLUS Trouble-shooting Guide for information on checking the flame signal.

Check the ignitor for fouling or damaged insulation if a low flame signal is read.

Check ground wiring and continuity as a cause for low flame signal. Replace igni- tor if ground and continuity conditions are satisfactory.

Check Combustion Levels

Refer to page 53 of this manual for mea- suring combustion levels and burner adjustments.

Review With Owner

Ensure the owner understands the impor- tance to perform the maintenance schedule specified in this manual.

Remind the owner of the importance to call a licensed contractor should the unit or sys- tem exhibit any unusual behavior.

62

Image 68

Delta PG PLUS-25 warranty Check Burner Flame Flame Signal, Check Combustion Levels, Review With Owner

Contents

For Your Safety PG PLUS-25/30/35/40 Gas Fired Combination Heaters Table of Contents Section VI Vent / Combustion AIR Installation Section V Primary Piping Section Viii Internal Wiring Section IX External WiringSection VII GAS Piping Section X START-UP Preparation Section XI START-UP Procedures Section XII Temperature LimitsSection Xiii CHECK-OUT Procedures Section XIV Installation Record Section Xvii Replacement Parts Product Specifications Product & Safety Information To Protect Against Excessive Temperature and Pressure Homeowner What to do if YOU Smell GASDo not try to light any appliance Operating Restrictions Pre-Installation Items Section I Pre-Installation Items Boiler ReplacementCode Compliance Determining Product Location Pre-Installation Items Residential Garage Installations Combustion Air and Venting Section II Combustion Air Venting Methods of Accessing Combustion Air Into a Space Combustion Air and VentingCombustion Air Requirements Air Openings Outdoor Combustion Air Equipment Located in Confined Spaces One Permanent Air Inlet Combination of Indoor and Outdoor Combustion Air Vent System Removal of an Existing Boiler f rom a Common Vent System Hydrostatic Test Procedures Unit Preparation Section III Unit PreparationHandling Instructions Hydrostatic Pressure Test Unit Preparation Completion of Hydrostatic Test and Draining Domestic Piping Section IV Domestic Piping Domestic Piping Multiple Units Installation Mixing Valve Assembly Domestic Piping Diagrams TR/SMART Series Application Performance Plus With Recirculation Performance Plus with Storage Tank Primary Piping Section V Primary Piping Primary Piping Closet Zero Clearance ApplicationsSystem Piping Zone Circulators Sizing Primary Piping System Piping Radiant Heating with Mixing Valve Personal injury, death or substantial property damage Primary Piping Near Appliance Piping Primary piping Zoning with Circulators Primary Piping Low Temperature Radiant System Primary Piping Venting and Combustion Air Installation Section VI Venting General Requirements Venting and Combustion Air Installation Category IV Vent Termination Clearances Venting Option Non Direct Vent / Vertical Multiple Vent TerminationsLocating the Combustion Air Inlet Venting Option Direct Vent / Vertical Venting Option Non-Direct Vent / Horizontal Venting Option Direct Vent / Horizontal Horizontal Wall Thimble Kit Determining Piping Lengths Excessive Horizontal Vent RunsVent Appliance Adapters Allowable Equivalent Length Combined Vent and Combustion Air Standard Horizontal Venting Installation Location of Air Inlet Termination Venting and Combustion Air Installation Section VII Gas Piping Recommended Gas Supply Piping Natural Gas Supply Pressure Requirements Natural GASPipe Sizing Natural Gas Propane Gas Supply Pressure Requirements Propane GASPipe Sizing Propane Gas Internal Wiring Section Viii Internal Wiring Wiring must be N.E.C Class Internal Wiring Factory Wiring Schematic Factory Internal Wiring External Wiring Section IX External Wiring Installation ComplianceOutdoor Temperature Limit Line Voltage Connections External Wiring Multiple Zone Field Wiring Using Zone Valves Field wiring with zone circulators Typical Zone Relay Panel Wiring Section X Start Up Preparation Performance Plus Filling the Outer Primary Tank and System Check Low Water Cut-Off Device Check Thermostat Circuit Verify Correct Pressure SwitchAir Shutter Settings Start-Up Procedures Final Checks Before Start-upPerformance Plus Start-up If Performance Plus Does Not Start Correctly For Your Safety Read Before Lighting Following instructions must be followed exactly, a fire orOr loss of life Operating Instructions Natural Gas Propane Temperature Limits Section XII Temperature Limits Recommended Secondary Thermostat Setting Temperature Limits Section XIII- Check-Out Procedures Section XIV Installation Record Section XV Maintenance Schedule Service TechnicianOwner Maintenance General Inspect the Burner Area Section XVI Maintenance ProceduresCheck the Surrounding Area Check Combustion/ Ventilation Air Openings Inspect Vent System and Combustion Air PipingCheck Domestic System Check Expansion Tank Check Temperature / Pressure Relief Valve Check Ignition Wiring and Ground WiringCheck Control Wiring Check Thermostat Limit Settings Review With Owner Check Burner Flame Flame SignalCheck Combustion Levels Section Xvii Replacement Parts Jacket Components Control Panel Components Electrical Panel Components Burner Components Specifications Graph 1 Performance Plus Pressure Loss Primary Side TTP Brazed Plate Heat Exchangers Maxi-flo Pool and Spa Heat Exchangers