ENGLISH

Getting

Operations Enabled During Playback

 

 

 

 

 

 

 

Switching the Angle

 

Started

 

 

 

 

 

 

 

BD

 

DVD-V

 

 

 

 

 

 

 

 

During playback of a BD or DVD-Video recorded with several

 

 

 

 

camera angles, you can change the angle.

 

HDMI Control Function

When you make an HDMI connection with a TV or AV Amp compatible

1

Set HDMI control function to “On”.

with DBP-4010UDCI and HDMI control functions, you can perform

the following operations by setting the HDMI control function of each

On the GUI menu, set “HDMI Setup” – “HDMI Control” (vpage

24).

device.

 

Connections

 

Press

during playback.

 

1 The angle number currently being played is displayed.

Setup

 

Angle

 

 

 

 

1/3

 

 

 

Playback

2

Use

to select angle.

 

 

 

 

 

HDMI

 

 

 

 

 

Angle

 

 

 

 

2/3

 

 

 

Control

 

 

 

 

 

 

 

 

 

 

 

Press .

 

 

Function

3 The setup screen disappears.

 

 

 

 

 

 

Information

NOTE

 

 

 

Angle changing may be restricted, depending on the disc.

 

 

 

 

 

Troubleshooting

Changing the Brightness of the

Display (Dimmer Control)

Press

.

 

 

Specifications

The display brightness each time the button is

pressed.

 

 

 

 

 

Normal

Dim

Dark Off

 

 

 

Even when “Off” is selected, the status of operations that are performed appears momentarily on the display if “Display Setup”

– “Temporary Display” on the GUI menu is set to “On” (vpage 30).

nTV or AV Amp power is turned on by operating the DBP-4010UDCI, and functions change with DBP- 4010UDCI input.

n Turning off the TV’s power turns the DBP- 4010UDCI’s power to standby.
n Operating the DBP-4010UDCI via the TV’s remote control.

(When the TV’s remote control has player operation buttons)

NOTE

•The HDMI control function controls operations of a TV that is compatible with the HDMI control function. Make sure that the TV and HDMI are connected when you perform HDMI control.

•Some functions may not operate depending on the connected TV or AV Amp. Check the owner’s manual of each device for details beforehand.

•When “Other Setup” – “Power Saving” on the GUI menu is set to “Power Saving Standby” or “Normal Standby” (vpage 31), the player’s power cannot be turned on using the HDMI control function.

•When “HDMI Setup” – “HDMI Control” – “Power Off Control” on the GUI menu is set to “Off” (vpage 24), the DBP-4010UDCI is not set to standby even if the connected device is in the standby mode.

•When “DENON LINK Setup” – “DENON LINK Mode” on the GUI menu is set to “4th”, the HDMI control function is enabled for the connected devices.

2Turn the power on for all the equipment connected by HDMI cable.
3Set the HDMI control function for all equipment connected by HDMI cable.

On the GUI menu, set the DBP-4010UDCI with “HDMI Setup”

– “HDMI Control” (vpage 24).

bPlease refer to the owner’s manual as regards setting of connected devices.

b Carry out Steps 2 and 3 should any of the equipment be unplugged.

4To ensure that the DBP-4010UDCI’s HDMI video output is projected on the TV screen, change the input function of the TV and AV Amp.

5When you turn the TV’s power to standby, check that the power of the DBP-4010UDCI and AV Amp also goes on standby.

If the HDMI control function does not operate properly, check the following points.

•Is the TV or AV Amp compatible with the HDMI control function?

•Are the HDMI control function settings of all equipment correct? (Step 3)

•After setting, did you add another HDMI device connection or make any changes in the connections? In this case, perform setting again.

47