Denon ADV-1000 23

ENGLISH

•Speaker system layout Basic system layout

• The following is an example of the basic layout for a system consisting of six speaker systems and a television monitor:

Subwoofer

Center speaker system

	Front speaker systems
	Set these at the sides of the TV or screen with
	their front surfaces as flush with the front of the	Surround speaker systems
	screen as possible.	Surround speaker systems
	screen as possible.

Contents

2We greatly appreciate your purchase of this unit “SERIAL NO 2Nous vous remercions pour l’achat de cet appareil “NO. DE SERIE 2SAFETY PRECAUTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: CAUTION 4.Follow Instructions – All operating and use instructions should be followed mounting accessory recommended by the manufacturer Grounding or Polarization – This product may be equipped with a polarized Power-Cord TABLE OF CONTENTS 1 BEFORE USING 2 CAUTIONS ON INSTALLATION 3CAUTIONS ON HANDLING 4FEATURES 5DISCS 6 CAUTIONS ON HANDLING DISCS 7 CONNECTIONS (2) Connecting video components To connect the video signal, connect using a (3) Connecting a video component equipped with S-Videojacks •A note on the S input jacks •Precaution when using S-jacks (4) Connecting the antenna terminals •An F-typeFM antenna cable plug can be connected directly If the FM antenna cable’s plug is not of the AM loop antenna assembly Connection of AM antennas (5) Connecting to a TV or Monitor Equipped with Component Input Connectors The video signals input to the VIDEO input (yellow) and Color component output connectors (PR/CR, PB/CB and Y) Connect in this way if your TV is compatible with Progressive Scan Use the three commercially available video cords to connect the (6) Sound output from this unit digital audio output connectors 2When a disc is played on the ADV-1000 •Linear PCM audio is the signal recording format used for music CDs (7) Speaker system connections (L) (R) Protector circuit Note on speaker impedance Cautions on connecting 8 PART NAMES AND FUNCTIONS Remote control unit 9REMOTE CONTROL UNIT (3)Preset memory (3) [1]Audio Component Table 1: Combinations of Personal System Codes [2] TV [3] VCR (4) Operating DENON audio components 1-c,z 1-a,b Press the CLEAR button while pressing the TUNER/TV/VCR c. For TUNER (5) Operating a video component stored in the preset memory 1-b 1-a a. For monitor TV 10SETTING UP THE SYSTEM Page (2) Before setting up the system Refer to “CONNECTIONS” (pages 8 to 15) and check that all connections are correct Turn on the power Press the POWER switch (button) (3) Quick system settings (to switch between the 2- and 5.1-channelmodes) About the quick system settings ROOM SPACE: SEATING POSITION: Settings: (4) System setting changes [1] Setting the type of speakers Parameters Subwoofer (SW FREQ.) frequency Select “80 Hz”, “120 Hz”, “150 Hz” or “180 Hz” (This is set to “80 Hz” by factory default.) Assignment of low frequencies Subwoofer mode [2] Setting the speaker distance Preparations: [3] Setting the channel level [4] Setting the DVD auto power off [5] After completing system setup 11PLAY BACK (3) Playback IMPORTANT SETUP INFORMATION This set has the following presettings: (3)-3 (3)-5 (4)-1 (4)Stopping Playback (5)Playing Still Pictures (Pausing) (8)-1 (7)-1 (6)Forward / Reverse Searching (7)Skipping to the Beginning of Chapters or Tracks (8)-1 (7)-1 12 OPERATION Input mode when playing DTS sources To check the currently playing program source, etc Input mode display PCM Input signal display After starting playback [1] Adjusting the sound quality (SDB / TONE) [2] Turning the sound off temporarily (MUTING) DEFEAT SDB 13 DOLBY / DTS SURROUND DTS Digital Surround 14SURROUND PLAYBACK [1]2-channelmode settings Surround parameters (1) (2-channelmode) AUTO-ST(auto stereo) mode PLII CINEMA / PLII MUSI / PRO LOGIC mode •PLII CINEMA (Dolby Pro Logic II CINEMA) mode •PLII MUSIC (Dolby Pro Logic II MUSIC) mode ON OFF YES OFF LOW MID HI YES NO [2] Playing in the Dolby Pro-Logic mode (All function) Page 15DSP SURROUND SIMULATION SMALL MED-SMED MED-LLARGE 0ms 30ms 110ms YES Y/NNO 2Surround modes and parameters 16LISTENING TO THE RADIO (3)Presetting FM and AM stations Example: Presetting FM station (currently tuned in) at preset number P03 1,3 Tune in the broadcast station that is to be preset and press the Memory button 17ON-SCREENDISPLAY 18USING THE ON-SCREENDISPLAY (2)Adjusting the picture quality 1, 2 1, 2, 3 STANDARD: SHARP: BLACK LEVEL (factory default: “LIGHTER”): LIGHTER (factory default): DARKER: Quit the picture quality adjustment mode (3) Playing Repeatedly [2]-1,2 [2] [1]-1 [1] [2] Playing a Certain Section Repeatedly (A-BRepeat Playback) (4) Playing Tracks in the Desired Order EX: To program track 5 and track 12: (5) Playing Tracks in the Random Order (6) MP3 Playback 2,3 To change the folder file you want to play, then press the PLAY (1) button or ENTER button • Playback starts The display can be switched between the single elapsed time and the single remaining time by (7)Using the Multiple Audio, Subtitle and Angle Functions [1]Switching the Audio Language (Multiple Audio Function) Before operating the remote control unit [2] Switching the Subtitle Language (Multiple Subtitle Function) [3] Switching the Angle (Multiple Angle Function) (8)Using the Menus (8) [1]Using the Top Menu [2] Using the DVD Menu 19USING THE TIMER SET TIME Adj AM12:00 PM7:00 EVERYDAY Timer FUNC Timer DVD PM12:00 PM12:35 Off Off PM12:00 PM12:56 (4)Setting the sleep timer (remote control unit only) 20 CHANGING THE DEFAULT SETTINGS (DVD) (1) “DISC SETUP” is selected 2,3,4 • DIALOG •SUBTITLE •DISC MENUS To exit the dialog mode 2When “SUBTITLE” is selected: ENGLISH JAPANESE OFF (Factory default) (2) “OSD SETUP” is selected • WALL PAPER To exit the osd setup mode 2When “WALL PAPER” is selected: •BLUE (Factory default) (3) “VIDEO SETUP” is selected See page • TV ASPECT Use this to set the shape of your TV’s screen TV TYPE 2When “TV TYPE” is selected: MULTI NTSC (Factory default) PAL To exit the TV type mode (4) “AUDIO SETUP” is selected •DIGITAL OUT •LPCM SELECT (96 kHz / 48 kHz) To exit the audio setup mode 2When “DIGITAL OUT” is selected “LPCM SELECT (96 kHz / 48 kHz)” is selected ON (96 kHz Æ 48 kHz) To exit the LPCM select mode Page Page (6) “OTHER SETUP” is selected •CAPTIONS To exit the other setup mode 2When “CAPTIONS” is selected: •OFF (Factory default) 21LAST FUNCTION MEMORY 22INITIALIZATION OF THE MICROPROCESSOR 23TROUBLESHOOTING Page 24SPECIFICATIONS