Denon ADV-1000 NOTE:, [3] Setting the channel level

ENGLISH

[3] Setting the channel level
			6	q When “AUTO” is selected in the “TEST TONE MODE”
• Use this setting to adjust so that the playback level between the
different channels is equal.
• From the listening position, listen to the test tones produced from
the speakers to adjust the level.
							C H A N N E L L E V E L			B
• The level can also be adjusted directly from the remote control unit.
							T E S T T O N E M O D E		AUTO	MANUAL
(For details, see page 40.)
							L E V E L C L E A R
					T E S T T O N E S T A R T			Y E S
1
	To perform these operations	from places other than the					F R O N T L		+ 1 0 d B
							CENTER			0 d B
	system setting change menu, see page 26.
							F R O N T R			0 d B
					SURROUND R			0 d B
2
	At the SYSTEM SETUP MENU select “CHANNEL LEVEL”.						SURROUND L			0 d B
							SUBWOOFER			0 d B
						SELECT :		FINISH: ENTER BUTTON
		ENTER
				• Test tones are automatically emitted from the different
					speakers.
				• The test tones are emitted from the different speakers in
					the following order, at 4-second intervals the first time and
	Remote control unit	Remote control unit			second time around, 2-second intervals the third time
					around and on:

• Switch to the CHANNEL LEVEL screen.

	C H A N N E L L E V E L			B
	T E S T T O N E M O D E		AUTO	MANUAL
L E V E L C L E A R
T E S T T O N E S T A R T
	F R O N T L			0 d B
CENTER			0 d B
F R O N T R			0 d B
SURROUND R			0 d B
SURROUND L			0 d B
SUBWOOFER			0 d B
SELECT :		FINISH: ENTER BUTTON

3	Select “TEST TONE MODE”.
	• Select the mode.

FRONT L CENTER FRONT R

SUBWOOFER SURROUND L SURROUND R

•Use the CURSOR buttons to adjust all the speakers to the same volume.

•The volume can be adjusted between –12 dB and +12 dB in units of 1 dB.

wWhen the “MANUAL” mode is selected

C H A N N E L L E V E L		B
T E S T T O N E M O D E	AUTO	MANUAL
L E V E L C L E A R
T E S T T O N E S T A R T		Y E S
F R O N T L	+ 1 0 d B
CENTER		0 d B
F R O N T R		0 d B
SURROUND R		0 d B
SURROUND L		0 d B
SUBWOOFER		0 d B

SELECT : FINISH: ENTER BUTTON

Remote control unit

Select “AUTO” or “MANUAL”.

•AUTO: Adjust the level while listening to the test tones produced automatically from the different speakers.

•MANUAL: Select the speaker from which you want to produce the test tone to adjust the level.

4	If “YES” is selected at “LEVEL CLEAR”, the level settings for
	all the speakers are set to 0 dB.
	B “YES” : The levels of the different speakers are all set to
	0dB.
	B “NO” : The speakers stay at their currently set levels.
5	Adjusting the channel levels in the “test tone” mode
	• Set the “TEST TONE START” mode using the	and
	cursor buttons, then select “YES” with the	cursor
	button to output test tones.

• Use the CURSOR left and right to select the speaker for which you want to output test tones, then use the CURSOR up and down to adjust so that the volume of the test tones from the various speakers is the same.

7	After the above settings are completed, press the ENTER
	button.
	• The “SYSTEM SETUP MENU” screen reappears.

To cancel the setting after adjusting

Display the channel level adjustment screen, then use the ,

, and cursor buttons to select “LEVEL CLEAR” and “YES”. The level settings for all the speakers are set to 0 dB.

NOTE:

•When you adjust the channel levels while in the SYSTEM SETUP CHANNEL LEVEL mode, the channel level adjustments made will affect ALL surround modes. Consider this mode a Master Channel Level adjustment mode.

•After you have completed the SYSTEM SETUP CHANNEL LEVEL adjustments, you can then activate the individual surround modes and adjust channel levels that will be remembered for each of those modes. Then, whenever you activate a particular surround sound mode, your preferred channel level adjustments for just that mode will be recalled. Check the instructions for adjusting channel levels within each surround mode on page 40.

29