Manuals / Brands / Home Audio / Stereo Receiver / Denon / Home Audio / Stereo Receiver

Denon 1083, AVR-3803 [2] Setting the Video Input Mode

1 84

Download 84 pages, 4.91 Mb

[2] Setting the Video Input Mode

1

2

At the System Setup Menu select “Video Setup” and press the ENTER button.

The “Video Setup” screen appears.

Select “Video Input Mode” and press the ENTER button.

3	Switch the Video Input Mode screen.

4	q Select the input source for which you	w Select the mode.
4	want to set the Video Input Mode.

AUTO:	When there are multiple input signals, the input signals are detected and the input signal to be output from the video
	monitor output terminal is selected automatically in the following order: component video, S-Video, composite video.
Component:	The signal connected to the component video terminal is always played.
	Video conversion is not conducted, so no image is output from the monitor output terminal when there is no input signal
	to the component terminal.
S-Video:	The signal connected to the S-Video terminal is always played.
	The S-Video input signal is converted and output from the composite and component monitor output terminal.
Video:	The signal connected to the composite video terminal is always played.
	The composite video input signal is up-converted and output from the S-Video and component monitor output terminals.

NOTE:

Down-converting from the component video signal to the S-Video and composite video signal is not possible, so when not using the component video monitor output terminal connect the player using the S-Video or composite video input terminal.

Cautions on the video conversion function:

When the component video terminals are used to connect the AVR-3803/1083 with a TV (or monitor, projector, etc.) and the video (yellow) or S video terminals are used to connect the AVR-3803/1083 with a VTR, depending on the combination of the TV and VTR the picture may flicker in the horizontal direction, be distorted, be out of sync or not display at all when playing video tapes.

If this happens, connect a commercially available video stabilizer, etc., with a TBC (time base corrector) function between the AVR- 3803/1083 and the VTR, or if your VTR has a TBC function, turn it on.

5	Enter the setting.
	At the “Video Setup” screen, select “Exit” and press the ENTER button.

The System Setup Menu reappears.

26

Contents

“SERIAL NO 2SAFETY PRECAUTIONS 2NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION Page 2INTRODUCTION TABLE OF CONTENTS 2ACCESSORIES 1 BEFORE USING 2 CAUTIONS ON INSTALLATION 3CAUTIONS ON HANDLING 4FEATURES 5 CONNECTIONS Connecting the video components Connecting the video components equipped with S-Videojacks •A note on the S input jacks MONITOR OUT jacks Cautions on the video conversion function: Connecting the antenna terminals Connecting the external input (EXT. IN) jacks Connecting the ZONE 2 jacks Speaker system connections Connections Protector circuit Note on speaker impedance 6 PART NAMES AND FUNCTIONS Remote control unit 7SETTING UP THE SYSTEM •Speaker system layout Basic system layout •Surround speaker selector function Before setting up the system Setting the type of speakers •Parameters Selecting the Surround Speakers for the different surround modes — Assignment of low frequency signal range — — Crossover Frequency — NOTE — Subwoofer mode — Setting the Delay Time Preparations: Setting the Channel Level Page Setting the Digital In Assignment [1] Setting the Component In Assign [2] Setting the Video Input Mode [1]Setting the power amplifier assignment [2]Setting the Zone2 vol. level Setting the Ext. In Subwoofer Level Setting the Auto Surround Mode Setting the On Screen Display (OSD) Setting the Trigger Out Setup Auto Tuner Presets Protecting the setting After completing system setup •On-screendisplay signals 8REMOTE CONTROL UNIT Using the remote control unit Operating DENON audio components Preset memory Operating a component stored in the preset memory Page Learning function 1, 4 2, 3 System call (1)System call buttons (2) Storing system call signals (3) Using the system call function Punch Through (1)Punch through button (2)Making the punch through setting (1) Setting the back light’s lighting time Resetting (1) Resetting the preset memory Page Page Page Page 9 OPERATION Playing the input source Example: CD AUTO PCM DTS Input mode selection function Note on playing a source encorded with DTS Input mode display Input signal display Example: Stereo Playback using the external input (EXT. IN) jacks Playing audio sources (CDs and DVDs) PURE DIRECT mode DIRECT mode STEREO mode After starting playback [1] Adjusting the sound quality (TONE) BASS TREBLE [2]Listening over headphones Multi-sourcerecording/playback [1] Playing one source while recording another (REC OUT mode) 2,42 3,53 2MULTI ZONE MUSIC ENTERTAINMENT SYSTEM (When using PREOUT) 2MULTI ZONE MUSIC ENTERTAINMENT SYSTEM (When using SPEAKER OUT) 10 SURROUND Fader function Surround parameters q Pro Logic II Mode: Panorama Control: Dimension Control: Center Width Control: DTS NEO:6 mode 1 3 2 4,5 2,6 4 5 2Dialogue Normalization Surround parameters w CINEMA EQ. (Cinema Equalizer): D.COMP. (Dynamic Range Compression): LFE (Low Frequency Effect): Adjusting the Audio Delay 11DSP SURROUND SIMULATION DSP surround simulation 1 2 1,3 Tone control setting Page Page 12LISTENING TO THE RADIO Checking the preset stations 13LAST FUNCTION MEMORY 14INITIALIZATION OF THE MICROPROCESSOR 15 TROUBLESHOOTING 16 ADDITIONAL INFORMATION Surround back speakers 2Number of surround back speakers Speaker setting examples 1.DTS-EScompatible system (using surround back speakers) (1)Basic setting for primarily watching movies (3)When using different surround speakers for movies and music (3) 2. When not using surround back speakers Surround Dolby Surround (1)Dolby Digital 2 Dolby Digital and Dolby Pro Logic 2Dolby Digital compatible media and playback methods DTS Digital Surround 2DTS compatible media and playback methods DTS-ESExtended Surround TM 2DTS-ESTM Discrete 2DTS-ESTM Matrix 2DTS Neo:6TM surround •DTS Neo:6 Cinema DTS 96/24 System setup items and default values (set upon shipment from the factory) Surround modes and parameters 2Differences in surround mode names depending on the input signals SPECIFICATIONS