Denon AVR-4802R CONNECTIONS, Connecting the audio components

5	CONNECTIONS
• Do not plug in the AC cord until all connections have been completed.		• Note that binding pin plug cords together with AC cords or placing them
•	Be sure to connect the left and right channels properly (left with left,	near a power transformer will result in generating hum or other noise.
	right with right).	• Noise or humming may be generated if a connected audio equipment
•	Insert the plugs securely. Incomplete connections will result in the	is used independently without turning the power of this unit on. If this
•	generation of noise.	happens, turn on the power of the this unit.
	Use the AC OUTLETS for audio equipment only. Do not use them
	for hair driers, etc.

Connecting the audio components

• When making connections, also refer to the operating instructions of the other components.

CD recorder or Tape deck	OUTPUT		INPUT
	R	L	R	L
B
	R	L	R	L

Connecting a tape deck

Connecting the AC OUTLETS

Connections for recording:

AC OUTLETS

Connect the tape deck’s recording input jacks (LINE IN or REC) to this unit’s

• SWITCHED

tape recording (OUT) jacks using pin plug cords.

(total capacity – 120 W (1 A.))

Connections for playback:

The power to these outlets is turned on and off in conjunction with

Connect the tape deck’s playback output jacks (LINE OUT or PB) to this unit’s

the

POWER

switch

on

the main unit, and

when the power is

tape playback (IN) jacks using pin plug cords.

switched between on and standby from the remote control unit.

Connecting a CD player

CD player

OUTPUT

No power is supplied from these outlets when this unit’s power is at

R

L

standby. Never connect equipment whose total capacity is above 120

Connect the CD player’s analog

W (1 A.)

output jacks (ANALOG OUTPUT)

NOTE:

to this unit’s CD jacks using pin

R

L

Only use the AC OUTLETS for audio equipment. Never use them for

plug cords.

hair driers, TVs or other electrical appliances.

Connecting the pre-out jacks

AC cord

Use these jacks if you wish to connect external power amplifier(s) to

(Supplied)

increase the power of the front, center, surround and surround back

sound channels, or for connection to powered loudspeakers.

AC outlets (wall)

When using only one surround back speaker, connect it to left

channel.

AC 120V, 60Hz

SPEAKER SYSTEMS

LOOP ANT.

IN

DVD

IN

TV

IN

DBS/

OUT

MONITOR

SPEAKER SYSTEMS

AM

SAT

FRONT

COMPONENT

FRONT

R

L

VIDEO

PRE OUT

Y

PB/CB

PR/CR

Y

PB/CB

PR/CR

Y

PB/CB PR/CR

Y

PB/CB

PR/CR

FR

FL

IN

OUT

OUT

SURROUND

CENTER

FM COAX. 75Ω

S-VIDEO

-A

C

L

SW

DVD

VDP

TV

DBS/

V. AUX

VCR-1

VCR-2

VCR-3

VCR-1

VCR-2

VCR-3

1-MONITOR-2

SURROUND

SR

SL

SAT

SURROUND

-A

-B

R

VIDEO

AC IN

L

SPEAKER

SBR

SBL

L

R

L

R

IMPEDANCE

SURROUND

ANTENNA

FRONT, CENTER,

SB / MULTI

-B

AUDIO

SB / MULTI

R

L

IN

OUT

IN

OUT

PRE OUT

SURROUND

6~16Ω

L

6~16Ω

SIGNAL PHONO

CD

DVD

VDP

TV

DBS/

V. AUX

VCR-1

VCR-2

VCR-3

VCR-1

VCR-2

VCR-3

CDR/

CDR/

MULTI

A OR B

Turntable

SAT

TAPE

TAPE

ZONE

A + B

8~16Ω

SB / MULTI

R

GND

L

L

L

AC OUTLETS

(MM cartridge)

R

R

R

R

POWER

AMP

EXT. IN

DIGITAL

OUT

IN

FRONT CENTER

SURROUND

SB

IN

OUT

RS-232C

OUT

ROOM TO ROOM

L

SWITCHED TOTAL 120W (1A) MAX.

REMOTE CONTROL

AV 120V 60Hz

R

1

2

3

2

3

4

4

SW

COAXIAL

OPTICAL

Extension jacks for future use

MD recorder, DAT deck or other component

Ground wire

equipped with digital input/output jacks

Connecting a turntable

B

Connect the turntable’s output cord to the AVR-4802R’s PHONO jacks,

OUTPUT

INPUT

OPTICAL

the L (left) plug to the L jack, the R (right) plug to the right jack.

NOTE:

COAXIAL

OPTICAL

CD

player

or other component

This unit cannot be used with

MC cartridges directly. Use a

equipped with digital output jacks

OUTPUT

separate head amplifier or step-up transformer.

If humming or other noise is generated when the ground wire is

Connecting the DIGITAL jacks

connected, disconnect the ground wire.

Use these for connections to audio equipment with digital output. Refer

to page 28 for instructions on setting this terminal.

NOTES:

• Use 75 Ω

/ohms cable pin cords for coaxial connections.

• Use optical cables for optical connections, removing the cap before connecting.

6