Denon DCD-F100, DRA-F100 manual Listening to Radio Programs, Auto Preset Memory Function, Tuning

7LISTENING TO RADIO PROGRAMS

(Check the connections on pages 5 and 6.)

ENGLISH

Auto Preset Memory Function

(FM ONLY)

TUNING

Receiver (DRA-F100)

3,5 2

B		PERSONAL COMPONENT SYSTEM / AM-FM STEREO RECEIVER DRA-F100			VOLUME
REMOTE SENSOR
				MHz	CH
	TIMER
SYSTEM	TUNED STEREO		AUTO
ON / STANDBY			BASS	TREBLE	BALANCE
TUNING	UP	MONO /
DOWN		BAND STEREO
PHONES

This function automatically stores the FM stations which can be received in the area in which the set is being used in the preset memory. Also note that the channel memories can be changed at will even after the preset stations have been stored with this function.

1	Connect the FM antenna and set it
	so that FM stations can be	Refer to page 5.
	received.

TIMER DISPLAY MEMORY FUNCTION

LR

	1	4,6
Example: Tuning in FM 87.5 MHz
	(AM stations are tuned in using the same procedure.)
	Set the VOLUME control on the	SYSTEM
	receiver to the minimum position,	ON / STANDBY
1 then press the SYSTEM power
	operation switch (SYSTEM ON/
	STANDBY) to turn on the power.
		BAND
2	Press the BAND button on the			MHz
	receiver to select the FM band.
	Use the TUNING UP and DOWN	TUNING	This lights when a station is tuned in.
	buttons to tune the frequency to
		DOWN	UP
3 87.50. Once the frequency is tuned				MHz
	in, adjust the volume to the desired		TUNED STEREO	AUTO
	level using the VOLUME control.

Auto Tuning

•When one of the TUNING buttons is pressed, the frequency changes in steps of 50kHz in the FM band, 9kHz in the AM band.

•If one of the TUNING buttons is held in for over 1 second, the frequency continues to change when the button is released (auto tuning) and stops when a station is tuned in. Tuning will not stop at stations whose reception is poor.

•To stop the auto tuning function, press the UP or DOWN button once.

	Press the SYSTEM power operation					SYSTEM
						ON / STANDBY	MEMORY
2	switch (SYSTEM ON/STANDBY) to								MEMO
	turn on the power while holding in
	the MEMORY button.						”AUTO“ is displayed and the MEMO indicator
							flashes during this operation.
	Searching begins automatically, and
	stations are stored in the preset
	memory in order, beginning from								MHz	CH
3 channel		1	(The	operation				TUNED STEREO	AUTO
	automatically		stops	once	40		When the operation is completed, the station
	stations	have	been	set in	the
							stored at preset number 1 is tuned in.
	memory.)

NOTES:

•In addition to the reception frequency, the reception mode (monaural or auto) is also preset, so check the display when presetting stations.

•If a station is preset at a number where a station is already preset, the previous station is replaced with the new station.

•The preset memory is not cleared immediately when the power cord is unplugged, but is cleared if the cord is left unplugged for an extended period of time. If this happens, preset the stations again.

Listening to Preset Stations

The preset stations can be recalled using the number buttons on the remote control unit.

Also, if the following operation is performed when the system power is off, the power automatically turns on and the radio is played. (Auto on function)

Example: Listening to the station preset at number 3

(This operation is only possible from the remote control unit.)

Presetting AM and FM Stations

Example: Presetting FM 87.5 (currently tuned in) at preset number 3

						Flashes
	Press the MEMORY button.	MEMORY
4
	The MEMO indicator flashes for					MHz	CH
			TUNED	STEREO	AUTO	MEMO
	10 seconds.
						Flashes
	Use the TUNING UP and DOWN					“P” flashes
	buttons to call out the number at		TUNING
5	which you want to preset the	DOWN	UP
						MHz	CH
	station (3), or simply press the		TUNED	STEREO	AUTO	MEMO
	corresponding number button “3”
	on the remote control unit.					Flashes
		MEMORY				“P3” lights
	Press the MEMORY button while
6
	the MEMO indicator is flashing.					MHz	CH
			TUNED	STEREO	AUTO

1	Press the TUNER button on the
	remote control unit.
2	Press button ”3“ on the remote
	control unit.

q w

POWER 8 9 2 MD 1

SLEEP				RESET	REC / MUTE
		DECK
6	7	2		0	1
EDIT	RANDOM	REPEAT		8	9
TIME	6		CD	2
SIDE A/B		7			1

PROGRAM CANCEL DIRECT TUNER FUNCTION

1 2 3 4 5

MHz CH

TUNED STEREO AUTO

Up to 40 AM or FM stations can be preset using this procedure.

11