Desa SDVBPD, SDVBND MANUAL LIGHTING procedure, Optional Hand-Held Remote Operation, Continued

OPERATING STOVE AND BURNER SYSTEM

Manual Lighting Procedure Optional Hand-Held Remote Operation

27

OPERATING STOVE WITH BURNER SYSTEM

Continued

MANUAL LIGHTING

procedure

1.Remove glass door (see Removing/Replacing Glass Door, page 24).

2.Follow steps 1 through 8 under Lighting Instructions, page 26.

3.Depress gas control knob and light pilot with match.

4.Keep gas control knob pressed in for 30 seconds after lighting pilot. After 30 seconds, release gas control knob. Now follow steps 10 through 14 under Lighting Instructions, page 26.

5.Replace glass door (see Removing/Replacing Glass Door, page 24).

OPTIONAL HAND-HELD

REMOTE OPERATION

Note: All remote control accessories must be purchased sepa- rately (see Accessories, page 38). Follow instructions included with the remote control.

NOTICE: You must light the pilot before using the hand-held remote control unit. See Lighting Instruc- tions on page 26.

1.After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the selector switch to the REMOTE position (see Figure 60). Note: The burner may light if hand-held remote was on when selector switch was last turned off. You can now turn the burner on and off with the hand-held remote control unit.

IMPORTANT: Do not leave the selector switch in the RE- MOTE or ON position when the pilot is not lit. This will drain the battery.

Selector Switch in Remote	Gas Control Knob	Variable
Position (Optional Remote
	in On Position	Control Knob
Control)
	LO

IN OUT

Figure 60 - Setting the Selector Switch, Control Knob, and Flame Adjustment Knob for Remote Operation

ON/OFF SERIES (MODELS GHRCB AND CGHRCB)

Hold the control button on the hand-held remote until burner turns on. Hold the control button again until burner turns off (see Figure 61).

To Lock press both buttons on hand-held remote control until light stops flashing. Hand-held remote control is now locked. If the fire is on it will be turned off automatically. In the locked state, the light will not light up when any button is pressed.

To Unlock press both buttons together on hand-held remote control untilthelightstopsflashing.Thehand-heldremoteisnowunlocked.

Control Button

Turns Burners

On and Off

Figure 61 - On/Off Hand-Held Remote Control Unit (C)GHRCB

THERMOSTAT SERIES (MODELS GHRCTB AND CGHRCTB)

Thehand-heldremotecanbeoperatedusingeitherthemanualmode (MANU) or thermostatic mode (AUTO) (see Figure 62). To select Fahrenheit/Centigrademodedisplay,carefullypressthe˚C/˚Fmode button with the end of a paper clip or similar blunt object.

Manual Mode

1.Press the POWER and LOCK buttons together to turn on the hand-held remote control.

2.Press the MANU button to turn on the fireplace.

3.Press the POWER and LOCK buttons together to turn off the fireplace.

Auto (Thermostatic) Mode

1.Press the POWER and LOCK buttons together to turn on the hand-held remote control.

2.Press AUTO button to select this mode.

3.Set the desired room temperature by pressing the TEMP + or - buttons.

4.Press the POWER and LOCK buttons together to turn off the fireplace

Note: Do not leave the hand-held remote in the AUTO mode close to the fireplace. The radiant heat from the fireplace will turn off the fireplace. Ideally, place the hand-held remote in the center of the room facing towards the fireplace.

Note: Do not hold the hand-held remote for a long time. Body temperature will affect its operation in the AUTO mode.

Digital Display	Turns Hand-Held
	Remote On or Off and
Shows
	Allows You to Choose
Temperature and
	the Manual Setting
Settings
Turns Burners	Selects Auto Setting
On or Off	Increases Room
Decreases Room	Temperature in
	AUTO Mode
Temperature in
AUTO Mode	Locks System to
	Prevent Accidental
	Ignition

Figure 62 - Thermostat Hand-Held Remote Control Unit (C)GHRCTB

For morevisit www..com

112126-01B