Owner’s Manual

Remote Control Setup and Operation

4.Point the remote control toward the device that was turned on in Step 1 and press in the first three-digit setup code number for that device using the number buttons (0-9) on the remote control.

The LED and selected Source button will blink and then stay lit after you enter a setup code.

Your device will turn off when the correct setup code number has been selected. If the device does not turn off, press in the next setup code number from the listing. The remote will remain in this program- ming mode as long as you continue to enter codes within 10 seconds of each other.

Continue entering setup code numbers until your device turns off, then proceed to Step 5.

Note: If you have tried all of the three digit setup code numbers listed for your device and it still did not turn off, please proceed to the Auto Search Method below to program your remote control.

5.Once your device turns off, press the Device Button selected in Step 3 once again to store the setup code number.

The LED and Source button will blink twice and then go out.

6.Test the remote control for your device. Try the POWER, CHANNEL UP and DOWN, VOLUME UP and DOWN buttons, etc.

If any of the buttons do not perform as they should, please repeat the setup from Step 1 using the next setup code number for your device.

Note: Some audio/video devices have separate buttons for POWER ON and POWER OFF. To operate these devices on the remote, press the corresponding Source button to turn the equip- ment ON and press the POWER button to turn the equipment OFF.

7.Please repeat the above steps to program the remote control for each of your other devices.

If none of the setup code numbers worked for your device during the standard setup procedure, or if the manufacturer or brand for your device is not listed in Setup Code Tables, use the steps below.

To program using Auto Search

1.Turn on the device you would like the remote control to operate, either manually or with its original remote control.

3.Press the corresponding Source button and the MUTE button on the remote control simultaneously.

The red LED and the selected Source button will illuminate.

Note: The selected button and LED will remain for approximately 10 seconds to indicate that the remote control is ready to be programmed. The following steps must be entered while they are lit. If the lights go out, simply press the Source and MUTE button again to re-enter the setup code.

3.Point the remote control toward the device and press the CHANNEL UP button on the remote control.

Each press of the CHANNEL UP button sends the signal for one setup code number. The LED and Source button will blink each time you press the CHANNEL UP button. Keeping the CHANNEL UP button pressed quickly scans through the setup code numbers.

Release the CHANNEL UP button as soon as the device turns off. Con- firm that you have the correct code by pressing the MUTE button on the remote. You should be able to turn your device on and off with this button.

If you pass the correct setup code number, you can return to it by pressing the CHANNEL DOWN button, one number at a time, until your device turns back on.

Note: During programming, the signal for POWER ON and POWER OFF is located on the MUTE button. For devices that use separate POWER ON and POWER OFF buttons, pressing the MUTE button on the remote control during programming will only turn the device OFF.

4.Once the correct code is confirmed, press the Source button to store the setup code number.

The LED and Source button will blink twice and then go out.

5.Test the remote control for your device. Try the POWER, CHANNEL UP and DOWN, VOLUME UP and DOWN buttons, etc.

If any of the buttons do not perform as they should, please repeat the setup from Step 1 using the next setup code number for your device.

Note: Some audio/video devices have separate buttons for POWER ON and POWER OFF. To operate these devices on the remote, press the corresponding DEVICE Button to turn the equip- ment ON and press the POWER button to turn the equipment OFF.

6.Please repeat the above steps to program the remote control for each of your other devices.

To display the stored three digit setup code number for a device:

1.Press the corresponding Source button and the MUTE button on the remote control simultaneously.

The red LED and the selected Source button will illuminate.

2.Press the T/V button.

The LED and Source button will quickly flash the three digit setup code number, pausing between numerals, that was stored for your device in that mode. The number zero (0) is indicated by ten flashes.

3.Please write your setup code numbers in the chart below, for future reference.

Set-Up Code Numbers:

CD

TV

 

 

DVD

VCR

 

 

AUX

CBL

 

 

SAT

 

 

 

38

Outlaw Audio

Page 37 Page 39
Page 38
Image 38
Dolby Laboratories 950 7.1 LED and Source button will blink twice and then go out, To program using Auto Search
Page 37 Page 39

950 7.1 specifications

Dolby Laboratories has long been synonymous with cutting-edge audio technology, and the introduction of the Dolby 950 7.1 system is a testament to its commitment to delivering immersive sound experiences. Designed for both professional and home environments, the Dolby 950 7.1 system offers a comprehensive suite of features that elevate audio quality to new heights.

At its core, the Dolby 950 7.1 system incorporates a seven-channel setup, which includes left, center, right, left surround, right surround, left back, and right back channels, coupled with a powerful subwoofer for enhanced low-frequency response. This arrangement allows for a truly enveloping soundstage, capable of recreating the nuances of a live performance or the explosive action of a blockbuster film.

One of the standout features of the Dolby 950 7.1 system is its sophisticated audio processing technology. Dolby Digital Plus support ensures that users can experience high-definition audio without compromising on quality. This format allows for increased bit rates and efficient compression, making it ideal for streaming services and Blu-ray content.

Additionally, the system benefits from Dolby Atmos technology, which adds a new dimension of sound by allowing sound designers to place audio elements in three-dimensional space. This innovative approach creates a more natural and realistic listening experience, as sounds can now come from above as well as from the traditional horizontal plane.

Furthermore, the Dolby 950 7.1 is designed with user-friendliness in mind, featuring intuitive setup and calibration options. Advanced room correction technology adjusts audio output based on the unique acoustics of any given space, ensuring optimal performance regardless of environmental factors.

For those looking to integrate this system into a home theater, the Dolby 950 7.1 provides seamless connectivity options. HDMI inputs, optical and coaxial digital inputs, and support for various streaming protocols make it easy to connect to a wide range of devices, from gaming consoles to smart TVs.

In summary, the Dolby 950 7.1 system exemplifies the pinnacle of modern audio technology, boasting features such as seven-channel surround sound, Dolby Digital Plus, and Dolby Atmos capabilities. With its focus on immersive experiences, user-friendly setup, and versatile connectivity, the Dolby 950 7.1 is truly a game-changer for audio enthusiasts and content creators alike. Whether in a professional studio or a personal home theater, this system delivers an unparalleled auditory experience.
Top Page Image Contents