Connect the Cables, Adsl Cable Notes | Eicon Networks 2440 instruction

Step 1: Connect the Cables

Leave your computer on when connecting the cables.

As shown in the diagram below, both the USB and Ethernet ports can be used at the same time. However, it is recommended that you use only one port during setup. Once you have verified that you can access the Internet, you can then connect a second computer.

ADSL

Cable

	USB	Yellow	Power
			Adapter
		Ethernet
	Cable
		Cable

To

Phone

Jack

ADSL Cable Notes

•Do not install a microfilter on the cable that connects your ADSL device to the telephone jack.

•If your Diva 2440 has a phone port, make sure you do not use this port to connect the ADSL cable.

•Several seconds after connecting the ADSL cable, the ADSL indicator light ( on the front of the device) should start flashing. This light will stop flashing and stay on when a link has been established with your ADSL service provider’s network.

Ethernet Cable Notes

•The Ethernet port can be used with any computer supporting an Ethernet card and TCP/IP.

•When connected, the Ethernet indicator light ( on the front of the device) will turn green when the Diva 2440 is plugged in and the computer is on.

•When finished connecting the cables, restart your computer so that your Ethernet card acquires a new IP address.

Setup

Page 16

Image 16

Eicon Networks 2440 manual Connect the Cables, Adsl Cable Notes, Ethernet Cable Notes

Contents

Diva 2440 Adsl Router User’s Guide Second Edition June 206-378-02 Contents Index Introduction How Adsl Works General Features Adsl and Network FeaturesHardware Features Introducing the Diva 2440 Adsl Router Package Contents One Computer Connection ScenariosTwo Computers at Once More than Two Computers Adsl line Diva Splitters and ‘Splitterless’ Operation How Adsl WorksMicrofilters Setup About Microfilters Technical Support Overview Connecting to Both PortsRequirements Internet Account Information Ports and Indicator Lights Ports Indicator Lights Power Light Adsl Cable Notes Connect the CablesEthernet Cable Notes USB Cable Notes Updating or reinstalling USB driversTo continue Access the Diva 2440 Web Interface Complete the Internet Wizard Link Setup Complete Optional Installing the Diva Assistant Setup Connecting a Second Computer LAN Setup About the Ethernet Cable General Setup Procedure Using the Diva Assistant to set on a LANBuilt-in Dhcp Server IP Addressing Adjusting LAN Settings If your LAN has a Dhcp ServerIf your LAN uses Static IP Addresses If your LAN has a router TCP/IP Setup Installing TCP/IPConfiguring TCP/IP Windows 95/98 Windows NT Windows Verifying TCP/IP SettingsApple Macintosh Mac OS 8 or later Setup Troubleshooting Browser Settings Connecting a Phone to the Pass-through Phone Port Connecting a Microfilter About Microfilters Technical Support Upgrading Firmware General Information Resetting the DeviceAbout the Diva Assistant General Information Resetting the Device Normal ResetReset Settings to Factory Defaults Boot Mode Starting the Web-based Configuration Interface Procedure ‘Reset’ and other buttons on the Main Menu Editing Settings Pages Configurations Saving, Restoring, and Resetting Accessing the ConfigurationBacking up the current configuration Restoring a configuration from a file Backing up Configuration Files Opening to the Firmware MaintenanceUpgrading Firmware Retrieving Firmware from the Eicon Networks Web Site Using your Diva Login Password and other Security Features Login PasswordDefining a password Erasing the system password IP Filtering Security Level Automatic Log OutNetwork Address Translation Launching the Diva Assistant About the Diva AssistantGeneral Tab Performance Tab Diagnostic Log TabTools Tab Advanced Topics Setting up a VPN with Windows 95/98 Virtual Private NetworkingDiva Requirements Instructions Advanced Topics Setting up a VPN with Windows Connecting the VPN Network Address Translation How It WorksSecurity benefits NAT static mappings Specifying a Default NAT Server Creating Static NAT Mappings ‘Default NAT Server’ field Diva Establishing a Telnet Connection Command Line Interface CLIPrerequisites Using the CLI Command Line Reference Uploading/downloading configuration files Using Tftp to Transfer FilesEnabling Tftp server support Loading New firmware via Tftp ExamplesRetrieving message.txt Command Line Reference Cancel Notational Conventions Adsl Commands Show Adsl ConfigurationSET Adsl Modulation Type G9922 Multimode Show Adsl Statistics ATM Commands Show ATM ConfigurationSET ATM Service Category UBR CBR Show ATM VC Dhcp Commands Primary Wins server Secondary Wins serverIpaddress IP address of the Wins server Domain Domain name, a string of up to 31 characters Ipaddress IP address of the entry to enable or disable Ipaddress IP address of the entry to deleteDelete Dhcp Staticmap ipaddress Show Dhcp Staticmap Show Ethernet Statistics Ethernet CommandsShow Ethernet Address Filter Commands Number Position where new filter is to be addedNumber Number of the filter that is to be deleted Number Number of the filter to edit Filter applies to both incoming and outgoing data default Number Number of the filter to copyDiscard the data Forward the data to the next filter Applied to TCP data default Applies to all dataApplies to UDP data Applies to TCP connection SYN data Enable Ethernet multicast filtering Disable Ethernet multicast filteringMacaddress Source or destination MAC address Type Hexidecimal number indicating type of Ethernet frame General Commands Hours Range 00 to Minutes Seconds Reset Reset FactoryEnable Echo Server Disable Echo Server Enable Sysman Disable Sysman IP Commands General Show Statistics Ping ipaddress number size IP Routing Commands Show IP Route Enable all module messages Logging and Internal Trace CommandsTaskName Module name as seen in Show LOG. Examples Dhcp NAT Network Address Translation Commands Enable NAT Disable NATUDP or TCP protocol Show IP NAT PPP Commands Value Range 0-2147483647. Default Value Range 0-2147483647 milliseconds. Default Enable PPP Echo Request Disable PPP Echo RequestEnable PPP Phase Logging Disable PPP Phase Logging Enable PPP FSM Logging Disable PPP FSM Logging SET PPP Local Username SET PPP Local Password Show PPP Configuration Profile Commands Enable Profile Disable ProfileShow Profiles Connect Disconnect SAR Commands Show SAR ConfigurationIndex Index of the VC taken from the SAR VC table Show SAR VC index Tftp Commands Enable Tftp Server Disable Tftp Server Time Protocol Commands Enable Timeprotocol Disable TimeprotocolShow Timeprotocol Configuration TimeServer Address of the time server Regulatory Information for Canada SpecificationsThis Section Specifications General Specifications Software and Firmware Specifications Declaration of Conformity Regulatory Information for the United StatesFCC Part 68 Notice Safety Notice Regulatory Information for Canada Safety Status TNV-3 Power ConsumptionRegulatory Information for the European Union EU Declaration of Conformity Index Index