Eicon Networks 2440 Windows NT 4.0

Setup Page 28

5.

Click the ‘DNS Configuration’ tab and select ‘Disable DNS.’ This instructs your computer to

obtain DNS server information via DHCP.

6.

Click ‘OK’, then click ‘OK’ again.

7.

If prompted to restart your system:

• Click ‘No’ if you are next going to install the Diva Assistant. You are required to

restart after installing this software, and clicking ‘No’ will save you some time.

• Click ‘Yes’ if you do not need to install the Diva Assistant. Your computer must be

restarted in order to acquire a new IP address.

Windows NT 4.0

The following procedure describes how to install TCP/IP on Windows NT 4.0. If TCP/IP is

already installed on your system, see Configuring TCP/IP (below). Note that if you have more

than one adapter installed on your system, you will have to use the adapter that is in use by the

Diva 2440.

1.

Click ‘Start’, ‘Settings’, ‘Control Panel’.

2.

Double-click the ‘Network’ icon. The Network dialog box appears.

3.

Click the ‘Protocols’ tab.

• If ‘TCP/IP’ is not listed, go to Installing TCP/IP (below).

• If ‘TCP/IP’ is listed, then the protocol is already installed. Go to Configuring

TCP/IP (below).

Installing TCP/IP

1.

From the ‘Protocols’ tab, click ‘Add’.

2.

Select ‘TCP/IP protocol’ as your network protocol, then click ‘OK’.

3.

Click ‘Yes’ to use DHCP.

4.

When prompted, insert the original Windows NT insta llation CD and enter d:\i386 (where d:

is the drive letter of your CD drive), and click ‘Continue’.

5.

Do not click the ‘OK’ button yet; next you will verify your TCP/IP settings. Go to Configuring

TCP/IP (below).

Configuring TCP/IP

1.

Click the ‘Protocols’ tab.

2.

Select ‘TCP/IP protocol’, then click ‘Properties’.

3.

Select ‘Obtain an IP address from a DHCP server’.

4.

Click the ‘DNS’ tab. Delete any DNS addresses are configured.

5.

Click ‘OK’.

Note: You may be asked to insert your original Windows installation CD-ROM.

Contents

Main Second Edition (June 2001) 206-378-02 Contents Command Line Reference...........................................................................60 Specifications and Regulatory Information...............................................86 Page Introducing the Diva 2440 ADSL Router General Features ADSL and Network Features Hardware Features Packag e Content s Connection Scenarios One Computer Two Computers atOnce More than Two Computers How ADSL Works Splitters and Splitterless Operation Microfilters Setup Overview Connecting to Both Ports Requirements Internet Account Information Ports and Indicator Lights Ports Indicator Lights Step 1: Connect the Cables ADSL Cable Notes Ethernet Cable Notes USB Cable Notes Updating or reinstalling USB drivers To continue Step 2: Access the Diva 2440 Web Interface Step 3: Complete the Internet Wizard Page Optional: Installing the Diva Assistant Page Connecting a Second Computer LAN Setup About the Ethernet Cable General Setup Procedure Built-in DHCP Server Using the Diva Assistant to set on a LAN IP Addressing Adjusting LAN Settings TCP/IP Setup Windows 95/98 Configuring TCP/IP Windows NT 4.0 Configuring TCP/IP Windows 2000 Apple Macintosh (Mac OS 8 or later) Page Troubleshooting Browser Settings Connecting a Phone to the Pass-through Phone Port About Microfilters Connecting a Microfilter Page Using your Diva 2440 General Information Resetting the Device Normal Reset Reset Settings to Factory Defaults Boot Mode Starting the Web-based Configuration Interface Procedure Reset and other buttons on the Main Menu Editing Settings Pages Configurations Saving, Restoring, and Resetting Upgrading Firmware Backing up Configuration Files Opening to the Firmware Maintenance Page Retrieving Firmware from the Eicon Networks Web Site Uploading New Firmware Page Login Password and other Security Features Login Password Automatic Log Out IP Filtering Security Level Network Address Translation About the Diva Assistant Launching the Diva Assistant General Tab Performance Tab Tools Tab Diagnostic Log Tab Page Virtual Private Networking Setting up a VPN with Windows 95/98 Page Setting up a VPN with Windows 2000 Connecting the VPN Network Address Translation Notes Security benefits NAT static mappings How It Works Creating Static NAT Mappings Page Example: Allowing Web or FTP Request using NAT Static Mappings Command Line Interface (CLI) Prerequisites Establishing a Telnet Connection Using the CLI Command Line Reference Using TFTP to Transfer Files Prerequisites Enabling TFTP server support Uploading/downloading configuration files Examples Command Line Reference Overview Notational Conventions ADSL Commands ATM Commands DHCP Commands Page <ipaddress> IP address of the entry to delete. <ipaddress> IP address of the entry to enable or disable. Page Filter Commands <number> Position where new filter is to be added. <number> Number of the filter to edit. <number> Position where new filter is to be added. <number> Number of the filter that is to be deleted. Page Page Page General Commands Page IP Commands (General) Page IP Routing Commands Logging and Internal Trace Commands taskName A module name (as seen in SHOW LOG). Examples: DHCP. ALL Enable all module messages. hostAddr IP address of the remote device (only required when enabling). NAT (Network Address Translation) Commands Use DELETE IP NAT to remove the NAT assignment. PPP Commands Page Page Profile Commands SAR Commands <index> Index of the VC taken from the SAR VC table. TFTP Commands Time Protocol Commands Page Specifications General Specifications Packaging Contents Hardware Features LED Status Indicators Software and Firmware Specifications Installation Features Administration Features ADSL Features IP Services Regulatory Information for the United States Declaration of Conformity FCC Part 68 Notice Safety Notice Regulatory Information for Canada Safety Notice Regulatory Information for the European Union EU Declaration of Conformity Index A C D E