Emerson 7000, 4000 Features Settings

2 --- 6Settings

Features Settings

Unless otherwisespecified on the order, the controller featuressettings are set at the

factory to the default values. Ifa se tting must be changed, follow the procedure onthe

next page. Some settings may require a password ( if the controller is set up for one).

Any indiscriminatechange in these settings may affectthe normal operation of the Automatic Trans-

fer Switch. This change could allow the load circuits to remain connected to an inadequate source.

Feature Default Setting Adjustment Range Display Screen

(see next page)

commit to transfer no yesor no Commit to Xfer A fter

TD Norm Fail

shed load direction from E from N or from E SHED LOAD

Direction

shed load in phase no yes or no SHED LOAD

InPhase

shed load in phase time delay 1.5 second 0to3.0seconds

0.1 sec increments

SHED LOAD

TD

shed load isolate load

on source failure ②yes yes or no SHED LOAD

IsoLoadOnSrcFail

shed load isolate loadon test 17 ②no yes or no SHEDLOAD

IsoLoadOnTest17

phase rotation monitor enable ③no yes or n o

PHASE ROTATION

MONITOR

Enable

phase rotation monitor referen ce ③ABC ABC or CBA

PHASE ROTATION

MONITOR

Reference

inphase monitor enable ④no yes or no

IN–PHASE

MONITOR

Enable

inphase monitor time delay ④1.5 second 0to3.0seconds

0.1 sec increments

IN–PHASE

MONITOR

Time Delay

failure to sync auto bypass ①no yes or no CTTS BYPASS/SHEDLD

FailSync AutoB yps

bypass time delay ①0second 0to59seconds

1 sec increments

CTTS BYPASS/SHEDLD

Bypass DT Delay

bypass in phase ①no yes or no CTTS BYPASS/SHEDLD

Bypass InPhase

Y–Y primary failure detection enable no yes or no Y–Y PRI FAIL DETECT

Enable

Y–Y primary failure sensing time delay 1.0 second 0to9.9seconds

0.1 sec increments

Y–Y PRI FAIL DETECT

Sense Delay

Y–Y primary failure retransfer time delay 1.0 hour 0to23hrs59min.

1 min. increments

Y–Y PRI FAIL DETECT

TD E>N Y–Y

①These features appear only on the display fora 4ACTS, 7ACTS, or7ACTB closed–transition transfer switch.

②These features appear only on t he display for a 4ACTS, 7ACTS or 7ACTB closed–tra nsition transfer switch

or a 4ADTS, 7ADTS, or 7ADTB delayed–transition transfer switch.

③These features do not appear on the display unless boths ourceshave 3 phase sensing enabled.

④These features appear only on a 4 ATS,7 ATS,or 7 ATB(op en–transition automatic transfer sw itch).

Contents

Main 381333126 K Users Guide Group 5 Controller for 4000 & 7000 Series Automatic Transfer Switch Products Power Control Center keypad and display Description Control Overview Settings Overview Password Default password is 1111 (see page 28) 2--1 Settings How to Change a Setting Tips 2 --- 2Settings Voltage & Frequency Settings 2--3 Settings Voltage & Frequency Settings 5 Voltage & Frequency Menus (last menu loops back to first) CP Settings seepage21 Normal Voltage seepage21 Normal Frequency seepage21 Normal Voltage Unbalance seepage21 Time Delay Settings Time Delay Settings 2 --- 6Settings Features Settings 2--7 Settings Features Settings 7 Features Menus (last menu loops back to first) Commit to Xfer After TD Normal Fail seepage21 Shed Load seepage21 Shed Load Options seepage21 Phase Rotation Monitor seepage21 General Settings 2--9 Settings General Settings 6 General Settings Menus (last menu loops back to first) Default to Factory Settings seepage21 Reset Engine Exerc Program s seepage21 Menu Language (not shown) see page 21 Serial Communication seepage21 Engine Exerciser Settings * For the year 2000, enter 00. Engine Exerciser Settings 2--12Settings View Event Log Logged Events Event Types Event Reasons 2--13 Settings Service Statistics / Diagnostics 7 Service Menus (last menu loops back to first) ATS Statistics Source Statistics View Service Data Serial Communication Service Factory Selectable Features 8 Service Menus (last menu loops back to first) ATS Information Testor Manual Mode Input Retransfer Mode Input Xfer to Normal Inhibit and Emergency (not shown) Status Information ATS Status Normal Source Status Emergency Source Status Source Acceptability Display Messages and their Meaning continued on next page The followingmessages (in alphabetical order) can appear on the CP display: 3--3 Operating the Controls Display Messages and their Meaning (continued) The followingmessages (in alphabetical order) can appear on the CP display: 4--1Description of Operation OpenTransition (2position) Automatic Transfer (4ATS,7ATS,7ATB) Load Transfer To Emergency 4--2 Description of Operation OpenTransition (2position) Automatic Transfer Switches continued Load Retransfer To Normal 4--3Description of Operation ClosedTransition Automatic Transfer (4ACTS, 7ACTS, 7ACTB) OpenTransition Load Transfer to Emergency Source due to Normal Source Failure 4--4 Description of Operation ClosedTransition Automatic Transfer Switches continued ClosedTransition Load Transfer to Emergency Source due to Transfer Test 4--5Description of Operation ClosedTransition Automatic Transfer Switches continued ClosedTransition Load Retransfer To Normal Bypass ClosedTransition Load Transfer 4--6 Description of Operation DelayedTransition Automatic Transfer (4ADTS, 7ADTS, 7ADTB) Load Transfer To Emergency 4--7Description of Operation DelayedTransition Automatic Transfer Switches continued Load Retransfer To Normal A --- 1 Appendix Controller Cover Removal NOTICE ATTENT ION DIP switch actuators see page A2 Voltage jumper blocks see page A4 Figure A1. Cover r elease latches. DIP Switch Actuators Tran sfer Sw itch Ty pe Nominal Source Voltage Selection DIP switch actuators 3, 4, 5, and6 select the input volt- age to the controller. See Table B. Figure A2. Location of DIP switch. A --- 3 Appendix Frequency of Sources Phases of Normal & Emergency Sources Data Input Lock Lost or Forgotten Password A --- 4Appendix Voltage Jumper Blocks Figure A4. Power sup ply jumper arrangements. Figure A3. Location of jumper blocks. INDEX A B C D E