Wall Mounting | Emerson Figure i guide

Installation

Figure 3 Dimensional data, 277V step-down transformer

.281" (7mm) Dia.		.31" (8mm) Dia.
.281" (7mm) Dia.		For rigid mounting
For wall mounting		For rigid mounting
For wall mounting		and shipping
		and shipping
1D18214P1	1/4-20 (2 screws &
1D18214P1	lock washers) for
10.3" (262mm)	rigid mounting and
1D18214P2	shipping
11.68" (297mm)
		Remove screws &
		attach bracket
5.5"	4.92"
(140mm)	(125mm)	Access to electrical
		connections from
WALL MOUNTING		bottom
WALL MOUNTING		RIGID MOUNTING

Notes:

1.1D18214P1 = Acme catalog no. T-1-37921 for all small systems except 3-ton Liebert DataMate with integral condenser.

2.1D18214P2 = Acme catalog no. T-1-37922 for 3-ton Liebert DataMate with integral condenser.

3.Epoxy coated. Suitable for indoor/outdoor service. Horizontal- or vertical-mount. Totally enclosed, non-ventilated.

4.Both brackets are shipped loose with transformer.

WIRING FOR TRANSFORMER

277V line voltage

Jumpers

H4	H2
	H2	H1
	H3	H1	X4	X3	X2	X1
	H3		X4

		Notes:
		1.	Jumper as shown.
	230V to unit	2.	Connect 277V line to H4 and X1				DPN000647
	230V to unit	3.	Connect 230V load to H1 and H4				REV. 0
		3.	Connect 230V load to H1 and H4				REV. 0

5

Image 9

Emerson Figure i manual Wall Mounting

Contents

Liebert Prop Fan Condensing Unit = 380/415-3ph-50Hz Example PFH037A-PL7 Table of Contents Figures Optional Equipment Prop Fan Condensing Units Location Considerations Equipment Inspection Net Weight Dimensional DataModel Numbers Dimensional Data, in. mm Lb. kg 60Hz 50Hz Cabinet and floor planning data, horizontal air discharge Footprint Dimensions Wall Mounting Electrical and piping connections, horizontal air discharge Piping and Electrical Connections PFH096A- L 152 General piping arrangement Top Air Discharge Models Electrical field connections, 1- to 5-ton units Electrical field connections, 8-ton units Single-phase, 1-3 ton model schematic, typical Three-phase, 3-5 ton model schematic, typical Three-phase, 8 ton model schematic, typical Piping for Elevation Differences between PFH and Evaporator Piping Considerations Evaporator Condensing UnitEquivalent lengths for various pipe fittings, ft m Field-Fabricated Line Sets Pre-Charged Line SetsRefrigerant charge in Liebert pre-charged R-407C line sets Line Size Length Charge R-407C Ft. m Lb-oz kg Recommended line sizes, OD Cu Liebert PFH unit charge levels and coupling size Piping connection sizes and torque Installation of Piping to UnitsLine charges refrigerant per 100 ft m of Type L copper tube Line Size OD Cu Coupling Size Torque, lb-ft. N-m Filter Drier Selection and Installation Install the New Condensing UnitRemove Existing Condensing Unit General System Charge Requirements Evaporator Charge LevelsEvaporator Charge R-407C Indoor Unit Models Oz kg Low-Voltage Control Wire Connections Low-Voltage Control Wire SizingElectrical Connections Nominal Input Voltage-Phase Capacity Electrical Nominal Input Voltage- Phase Capacity ElectricalElectrical Data Electrical data-High ambient models 105F/41C 60Hz Electrical data-High ambient models 105F/41C 50Hz Electrical data-Quiet-Line models 95F/35C 60Hz Electrical data Quiet-Line models 95F/35C 50Hz Checklist for Completed Installation Compressor High Head PressureLiebert Lee-Temp Flood Back Head Pressure Control Adjustment Hot Gas BypassOperation Hot gas bypass diagram Compressor Failure GeneralElectrical Failure-Burnout Mechanical Failure Compressor Replacement Field Charge Verification Field verification chargeModel Numbers 407C 60 Hz 50 Hz Oz kg Problem Cause Remedy Troubleshooting Web Site Monitoring Single-Phase&Three-Phase UPS Environmental SystemsUni Etwo