Manuals / Emerson / Household Appliance / Water System

Emerson PN 51-1055pHC/rev.K instruction manual Choose Noise Rejection

Models: PN 51-1055pHC/rev.K

1 87

Download 87 pages 1.18 Kb

Page 51

MODEL SOLU COMP II	SECTION 5.0
	PROGRAMMING THE ANALYZER

5.8 NOISE REJECTION

5.8.1 Purpose.

For maximum noise rejection, the frequency of the ac power must be entered in the analyzer.

5.8.2. Procedure.

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

CalibrateHold

ProgramDisplay

OutputsAlarms

Measurement>>

TempSecurity

#Sensors>>

Noise Rejection

ResetAnalyzer >>

1.Press MENU. The main menu screen appears. Choose Program.

2.Choose >>.

3.Choose >>.

4.Choose Noise Rejection.

5.Enter the mains frequency, 50 Hz or 60 Hz.

6.The display returns to the Noise Rejection screen. To return to the main menu, press EXIT. To return to the main display, press MENU followed by EXIT.

5.9 SINGLE SENSOR OR DUAL SENSOR INPUT

5.9.1 Purpose

The Solu Comp II accepts input from a single sensor or from two sensors. This section describes how to program the analyzer for single or dual sensors. COMPLETE THIS SECTION BEFORE DOING OTHER PROGRAMMING.

5.9.2 Procedure.

To choose a menu item, move the cursor to the item and press ENTER.

To store a number or setting, press ENTER.

CalibrateHold

ProgramDisplay

OutputsAlarms

Measurement>>

TempSecurity

#Sensors>>

#of sensors?

OneΤωο

1.Press MENU. The main menu screen appears. Choose Program.

2.Choose >>.

3.Choose #Sensors.

4.Choose One or Two. Choosing One configures the analyzer as a pH ana- lyzer. Conductivity cannot be selected for single measurement.

5.The display returns to the # Sensors screen. To return to the main menu, press MENU. To return to the main display, press MENU followed by EXIT.

42

Image 51

Emerson PN 51-1055pHC/rev.K instruction manual Choose Noise Rejection

Contents

Model Solu Comp Essential Instructions Quick Start Guide ORP Quick Reference Guide Model Solu Comp List of Tables Table of Contents CONT’DIii List of FiguresAbout This Document Section Description and Specifications Ordinary Location -68 only DimensionsTerminal Connections Rating 26-14 AWG wire size Hazardous LocationRange, µS/cm Cell constant, /cm Performance SpecificationsAnalyzer Conductivity Input Recommended Sensors for ConductivityMeasurement Range see table below Toroidal Conductivity Codes -21 and/orRecommended Sensors for ORP Performance Specifications Analyzer ORP InputTemperature Correction none required When used with conductivity -20-32 orRecommended Sensors Frequency Range 0.5 4000 HzRepeatability ±1% Measurement Range 0-10 ppm mg/L Loop Specifications with a Model 499A OZ SensorRecommended Sensor Input filter 1- 255 samplesModel 1055 Solu Comp II Analyzer Ordering InformationCombination Guide Part Number Description Weight General Information Section InstallationInstallation Unpacking and InspectionPanel Mounting Panel Mount InstallationPipe Mounting Pipe Mount InstallationSurface Mounting Surface Mount InstallationSection Wiring POWER, ALARM, OUTPUT, and Sensor ConnectionsPreparing Conduit Openings Model Solu Comp Section Wiring Model Solu Comp Section Wiring 41055105 41055106 41055107 41055108 41055109 41055110 40105536 40105559 Section Display and Operation DisplayKeypad Programming and Calibrating the Solu Comp II Tutorial Security Using HoldSection Programming the Analyzer Changing Startup SettingsSensors Output Section Default SettingsOutput Dampening Or 4 mA Mode Section Alarm SectionDefault Settings Assigning Outputs 1 DefinitionsChoose Output Range. Choose Output1 or Output2 Choose Output ConfigureChoose Output1 or Output2 Choose 4-20 mA or 0-20 mAAlarm Relays Must be Configured Before Assigning Setpoints Choose Measurement or Temp Choose Alarm ConfigureChoose Alarm Setpoints Definitions pH/ORP PurposeDefinitions conductivity/resistivity Choose Soln Temp Corr or Sensor Isoptntl Choose MeasurementDefinitions pH PurposeOutputsAlarms Measurement Choose Noise Rejection Noise RejectionChoose ResetAnalyzer Resetting Factory Calibration and Factory Default SettingsChoose Default Display Procedure Choosing a LanguageProcedure Changing Screen Contrast Introduction Section CalibrationPurpose Calibrating TemperatureProcedure Calibration Slope and Offset PH at 25C Standards Nominal pHEnter Choose Measurement Choose BufferCalManual Calibration pH S1ManualCal? Choose Measurement Choose Standardize Standardization pHEntering a Known Slope Value pH ORP Calibration Preparation of ORP standard solutionsProcedure-Calibration against a standard meter and cell Calibrating AN IN-SERVICE Sensor ConductivityChoose Measurement Choose InProcess Procedure-Calibration against a standard solution ProgramDisplay Calibrate? Choose Measurement Choose CellConst Placing a NEW Sensor in Service ConductivityCell constant Conductivity µS/cm Resistor k Ω Calibrating the Analyzer ConductivityChoose Measurement To Reset the Factory Resistance CALIBRATION, see SectionModel Description See Figure Section MaintenanceReplacement Parts OverviewExploded View of Solu Comp II Panel Mount Version Exploded View of Solu Comp II Pipe/Surface Mount Version Absolute Value of Measured Voltage Exceeds 2500 mV Section TroubleshootingOverview Troubleshooting Using Fault Codes Simulating Inputs Conductivity Simulating TemperatureEeprom Failure PH Sensitive Glass Membrane is BrokenConductivity Sensor Open or Shorted RTD Sense Line for Sensor 1 or Sensor 2 is OpenCalibration Error During Two-Point Calibration Problem See SectionCalibration Error during Standardization Invalid Input While Manually Entering SlopeSensor Does Not Respond to Known pH Changes Model Solu Comp Section Troubleshooting Calibration Error Using Standard Resistors Problem See SectionCurrent Output Too Low Alarm Relays Do Not WorkMeasurement seems wrong Conductivity, µS/cm Cell constant, /cmSimulating pH input when the preamplifier is in the sensor GeneralPreamplifier is in the Sensor Simulating Inputs Conductivity Set the temperature correction to raw SectionThree-Wire RTD Configuration Simulating temperatureChecking for a Poisoned Reference Electrode Measuring Reference VoltageGeneral Warranty RepairNON-WARRANTY Repair Section Return of MaterialWarranty Specifications subject to change without notice