Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks manual 1 The 6H352-25 Module, Introduction, Fast Enet, 354701, Reset Com

Models: 6H352-25

1 56

Download 56 pages 21.77 Kb

Page 18

Figure 1-1 The 6H352-25 Module

Figure 1-1 The 6H352-25 Module

FAST ENET

6H352-25

RESET

COM

1X

G

R

O

U

P

1

11X

13X

G

R

O

U

P

2

CPU

GROUP

SELECT

GROUPGROUP

23X

3547_01

1-2Introduction

Image 18

Enterasys Networks 1 The 6H352-25 Module, Introduction, Fast Enet, 354701, Reset Com, 1X G R O U P, 11X 13X G R O U P

Contents

6H352-25 6H352-25 Fast Ethernet Installation GuideRESET COM FAST ENETPage Enterasys Networks, Inc 35 Industrial Way Rochester, NH FCC NOTICE INDUSTRY CANADA NOTICEVCCI NOTICE ENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENT BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCTCAREFULLY READ THIS LICENSE AGREEMENT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU DECLARATION OF CONFORMITY Page INTRODUCTION ContentsABOUT THIS GUIDE ContentsSPECIFICATIONS INSTALLATIONTROUBLESHOOTING MODE SWITCH BANK SETTINGS AND OPTIONSFigures FiguresTables USING THIS GUIDE About This GuideImportant Notice STRUCTURE OF THIS GUIDE MATRIX E7 Overview and Setup Guide6C105 SmartSwitch 6000 Overview and Setup Guide RELATED DOCUMENTSDocument Conventions DOCUMENT CONVENTIONSThe guide uses the following conventions About This GuideGETTING HELP Introduction Important Notice1-2 Introduction RESET COMFigure 1-1 The 6H352-25 Module 6H352-251.3 RUNTIME IP ADDRESS DISCOVERY 1.1 CONNECTIVITY1.2 OPTIONAL HSIMs AND VHSIMs NOTE The 6H352-25 will reboot after RAD is successful1.6 REMOTE MONITORING RMON 1.4 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION1.5 SmartTrunk Half-Duplex/Full-Duplex Auto-Negotiation1.7 BROADCAST SUPPRESSION 1.8 PORT/VLAN REDIRECT FUNCTIONS1.9 TRAFFIC RATE LIMITING 1.11 GARP SWITCH OPERATION 1.10 FLOW CONTROL1.12 802.1 PORT PRIORITY Installation in the SmartSwitch 6000 chassis 1.15 SWITCHING OPTIONSInstallation in the MATRIX E7 Chassis 1.13 DISTRIBUTED CHASSIS MANAGEMENTStandards Compatibility 1.17 LANVIEW DIAGNOSTIC LEDs1.16 STANDARDS COMPATIBILITY 1-8 Introduction2.1 SmartTrunk FEATURE Network Requirements2.2 10BASE-T NETWORK 2.3 100BASE-TX NETWORK 100BASE-TX Network2-2 Network Requirements Installation 3.2 INSTALLING OPTIONAL HSIM, VHSIM, OR FLASH MEMORY UPGRADE 3.1 UNPACKING THE 6H352-253.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS 3-4 Installation Installing the Module into the MATRIX E7 ChassisFigure 3-1 Installing the 6H352-25 into the MATRIX E7 Chassis Connectors3.4 INSTALLING THE MODULE INTO THE SmartSwitch CHASSIS 3-6 Installation Installing the Module into the SmartSwitch ChassisFigure 3-2 Installing the 6H352-25 into the SmartSwitch 6000 Chassis Connector3.5 CONNECTING TO THE NETWORK Group Select Button RX LED TX LED Figure 3-3 Connecting a Twisted Pair Segment to the 6H352-25Figure 3-4 Crossover Cable RJ45 Pinouts Figure 3-5 Straight-Through Cable RJ45 PinoutsRJ45 to RJ45 3.6 COMPLETING THE INSTALLATION Completing the Installation3-10 Installation Troubleshooting 4.1 USING LANVIEWViewing Receive and Transmit Activity GROUP SELECT GROUP Using LANVIEW4-2 Troubleshooting Figure 4-1 LANVIEW LEDsNo link Table 4-1 LANVIEW LEDsBPDUs being sent if STA Table 4-1 LANVIEW LEDs ContinuedManagement User’s Guide for proper setup 4.2 TROUBLESHOOTING CHECKLISTSmartSwitch 6000 Series Modules Local Refer to the MATRIX E7 Series andSmartSwitch 6000 Series Modules Local Management User’s Guide for instructionsRefer to MATRIX E7 Series and SmartSwitch 6000 Series Modules LocalUsing the RESET Button 4.3 USING THE RESET BUTTONRESET Button Figure 4-2 RESET ButtonUsing the RESET Button 4-8 TroubleshootingProcessors/Memory SpecificationsI/O Ports PhysicalA.1 COM PORT PINOUT ASSIGNMENTS EnvironmentalSpecifications A-3 A.2 REGULATORY COMPLIANCESafety UL 1950, CSA C22.2 NoPage Mode Switch Bank Settings and Options B.1 REQUIRED TOOLSB.2 SETTING THE MODE SWITCHES Switch 6 - Forced BootP B.3 FLASH MEMORY UPGRADE B.3.1 Locating the FLASH MemoryB.3.2 Installing the FLASH Memory Installing Optional HSIM or VHSIM Interface Modules B.4 INSTALLING OPTIONAL HSIM OR VHSIM INTERFACE MODULESOptional HSIM or VHSIM HSIM/VHSIM Connectors Figure B-4 HSIM and VHSIM Connector LocationsIndex NumericsIndex-2