Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks 6H352-25 2.3 100BASE-TX NETWORK, 100BASE-TX Network, Network Requirements

Models: 6H352-25

1 56

Download 56 pages 21.77 Kb

Page 26

100BASE-TX Network

100BASE-TX Network

2.3100BASE-TX NETWORK

The fixed front panel ports of the 6H352-25 provide a connection that supports Category 5 UTP cabling. The device at the other end of the twisted pair segment must meet IEEE 802.3u 100BASE-TX Fast Ethernet network requirements for the devices to operate at 100 Mbps. Refer to the Enterasys Networks Cabling Guide for details.

NOTE: The fixed ports of the 6H352-25 support Category 5 UTP cabling with an impedance between 85 and 111 ohms for 100 Mbps operation.

The 6H352-25 is capable of operating at either 10 or 100 Mbps. The 6H352-25 automatically senses the speed of the other device and adjusts its speed accordingly.

2-2Network Requirements

Image 26

Enterasys Networks 6H352-25 manual 2.3 100BASE-TX NETWORK, 100BASE-TX Network, Network Requirements

Contents

6H352-25 6H352-25 Fast Ethernet Installation GuideRESET COM FAST ENETPage Enterasys Networks, Inc 35 Industrial Way Rochester, NH VCCI NOTICE FCC NOTICEINDUSTRY CANADA NOTICE CAREFULLY READ THIS LICENSE AGREEMENT ENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENTBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU DECLARATION OF CONFORMITY Page INTRODUCTION ContentsABOUT THIS GUIDE ContentsSPECIFICATIONS INSTALLATIONTROUBLESHOOTING MODE SWITCH BANK SETTINGS AND OPTIONSFigures FiguresTables Important Notice USING THIS GUIDEAbout This Guide STRUCTURE OF THIS GUIDE MATRIX E7 Overview and Setup Guide6C105 SmartSwitch 6000 Overview and Setup Guide RELATED DOCUMENTSDocument Conventions DOCUMENT CONVENTIONSThe guide uses the following conventions About This GuideGETTING HELP Introduction Important Notice1-2 Introduction RESET COMFigure 1-1 The 6H352-25 Module 6H352-251.3 RUNTIME IP ADDRESS DISCOVERY 1.1 CONNECTIVITY1.2 OPTIONAL HSIMs AND VHSIMs NOTE The 6H352-25 will reboot after RAD is successful1.6 REMOTE MONITORING RMON 1.4 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION1.5 SmartTrunk Half-Duplex/Full-Duplex Auto-Negotiation1.9 TRAFFIC RATE LIMITING 1.7 BROADCAST SUPPRESSION1.8 PORT/VLAN REDIRECT FUNCTIONS 1.12 802.1 PORT PRIORITY 1.11 GARP SWITCH OPERATION1.10 FLOW CONTROL Installation in the SmartSwitch 6000 chassis 1.15 SWITCHING OPTIONSInstallation in the MATRIX E7 Chassis 1.13 DISTRIBUTED CHASSIS MANAGEMENTStandards Compatibility 1.17 LANVIEW DIAGNOSTIC LEDs1.16 STANDARDS COMPATIBILITY 1-8 Introduction2.2 10BASE-T NETWORK 2.1 SmartTrunk FEATURENetwork Requirements 2-2 Network Requirements 2.3 100BASE-TX NETWORK100BASE-TX Network Installation 3.2 INSTALLING OPTIONAL HSIM, VHSIM, OR FLASH MEMORY UPGRADE 3.1 UNPACKING THE 6H352-253.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS 3-4 Installation Installing the Module into the MATRIX E7 ChassisFigure 3-1 Installing the 6H352-25 into the MATRIX E7 Chassis Connectors3.4 INSTALLING THE MODULE INTO THE SmartSwitch CHASSIS 3-6 Installation Installing the Module into the SmartSwitch ChassisFigure 3-2 Installing the 6H352-25 into the SmartSwitch 6000 Chassis Connector3.5 CONNECTING TO THE NETWORK Group Select Button RX LED TX LED Figure 3-3 Connecting a Twisted Pair Segment to the 6H352-25RJ45 to RJ45 Figure 3-4 Crossover Cable RJ45 PinoutsFigure 3-5 Straight-Through Cable RJ45 Pinouts 3-10 Installation 3.6 COMPLETING THE INSTALLATIONCompleting the Installation Viewing Receive and Transmit Activity Troubleshooting4.1 USING LANVIEW GROUP SELECT GROUP Using LANVIEW4-2 Troubleshooting Figure 4-1 LANVIEW LEDsNo link Table 4-1 LANVIEW LEDsBPDUs being sent if STA Table 4-1 LANVIEW LEDs ContinuedManagement User’s Guide for proper setup 4.2 TROUBLESHOOTING CHECKLISTSmartSwitch 6000 Series Modules Local Refer to the MATRIX E7 Series andSmartSwitch 6000 Series Modules Local Management User’s Guide for instructionsRefer to MATRIX E7 Series and SmartSwitch 6000 Series Modules LocalUsing the RESET Button 4.3 USING THE RESET BUTTONRESET Button Figure 4-2 RESET ButtonUsing the RESET Button 4-8 TroubleshootingProcessors/Memory SpecificationsI/O Ports PhysicalA.1 COM PORT PINOUT ASSIGNMENTS EnvironmentalSpecifications A-3 A.2 REGULATORY COMPLIANCESafety UL 1950, CSA C22.2 NoPage Mode Switch Bank Settings and Options B.1 REQUIRED TOOLSB.2 SETTING THE MODE SWITCHES Switch 6 - Forced BootP B.3 FLASH MEMORY UPGRADE B.3.1 Locating the FLASH MemoryB.3.2 Installing the FLASH Memory Installing Optional HSIM or VHSIM Interface Modules B.4 INSTALLING OPTIONAL HSIM OR VHSIM INTERFACE MODULESOptional HSIM or VHSIM HSIM/VHSIM Connectors Figure B-4 HSIM and VHSIM Connector LocationsIndex NumericsIndex-2