Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks 6H352-25 manual A.2 REGULATORY COMPLIANCE, Safety, UL 1950, CSA C22.2 No

Models: 6H352-25

1 56

Download 56 pages 21.77 Kb

Page 47

Regulatory Compliance

A.2 REGULATORY COMPLIANCE

This equipment meets the following safety and electromagnetic compatibility (EMC) requirements:

Safety:	UL 1950, CSA C22.2 No. 950,
	73/23/EEC, EN 60950, and IEC 950

Electromagnetic Compatibility (EMC): FCC Part 15, CSA C108.8, 89/336/EEC, EN 55022, EN 61000-3-2, EN 61000-3-3, EN 55024, EN 60825, AS/NZS 3548, and VCCI V-3

Specifications A-3

Image 47

Enterasys Networks 6H352-25 manual A.2 REGULATORY COMPLIANCE, Safety, UL 1950, CSA C22.2 No, 73/23/EEC, EN 60950, and IEC

Contents

FAST ENET 6H352-25 Fast Ethernet Installation GuideRESET COM 6H352-25Page Enterasys Networks, Inc 35 Industrial Way Rochester, NH VCCI NOTICE FCC NOTICEINDUSTRY CANADA NOTICE CAREFULLY READ THIS LICENSE AGREEMENT ENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENTBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU DECLARATION OF CONFORMITY Page Contents ContentsABOUT THIS GUIDE INTRODUCTIONMODE SWITCH BANK SETTINGS AND OPTIONS INSTALLATIONTROUBLESHOOTING SPECIFICATIONSFigures FiguresTables Important Notice USING THIS GUIDEAbout This Guide RELATED DOCUMENTS MATRIX E7 Overview and Setup Guide6C105 SmartSwitch 6000 Overview and Setup Guide STRUCTURE OF THIS GUIDEAbout This Guide DOCUMENT CONVENTIONSThe guide uses the following conventions Document ConventionsGETTING HELP Important Notice Introduction6H352-25 RESET COMFigure 1-1 The 6H352-25 Module 1-2 IntroductionNOTE The 6H352-25 will reboot after RAD is successful 1.1 CONNECTIVITY1.2 OPTIONAL HSIMs AND VHSIMs 1.3 RUNTIME IP ADDRESS DISCOVERYHalf-Duplex/Full-Duplex Auto-Negotiation 1.4 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION1.5 SmartTrunk 1.6 REMOTE MONITORING RMON1.9 TRAFFIC RATE LIMITING 1.7 BROADCAST SUPPRESSION1.8 PORT/VLAN REDIRECT FUNCTIONS 1.12 802.1 PORT PRIORITY 1.11 GARP SWITCH OPERATION1.10 FLOW CONTROL 1.13 DISTRIBUTED CHASSIS MANAGEMENT 1.15 SWITCHING OPTIONSInstallation in the MATRIX E7 Chassis Installation in the SmartSwitch 6000 chassis1-8 Introduction 1.17 LANVIEW DIAGNOSTIC LEDs1.16 STANDARDS COMPATIBILITY Standards Compatibility2.2 10BASE-T NETWORK 2.1 SmartTrunk FEATURENetwork Requirements 2-2 Network Requirements 2.3 100BASE-TX NETWORK100BASE-TX Network Installation 3.1 UNPACKING THE 6H352-25 3.2 INSTALLING OPTIONAL HSIM, VHSIM, OR FLASH MEMORY UPGRADE3.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS Connectors Installing the Module into the MATRIX E7 ChassisFigure 3-1 Installing the 6H352-25 into the MATRIX E7 Chassis 3-4 Installation3.4 INSTALLING THE MODULE INTO THE SmartSwitch CHASSIS Connector Installing the Module into the SmartSwitch ChassisFigure 3-2 Installing the 6H352-25 into the SmartSwitch 6000 Chassis 3-6 Installation3.5 CONNECTING TO THE NETWORK Figure 3-3 Connecting a Twisted Pair Segment to the 6H352-25 Group Select Button RX LED TX LEDRJ45 to RJ45 Figure 3-4 Crossover Cable RJ45 PinoutsFigure 3-5 Straight-Through Cable RJ45 Pinouts 3-10 Installation 3.6 COMPLETING THE INSTALLATIONCompleting the Installation Viewing Receive and Transmit Activity Troubleshooting4.1 USING LANVIEW Figure 4-1 LANVIEW LEDs Using LANVIEW4-2 Troubleshooting GROUP SELECT GROUPTable 4-1 LANVIEW LEDs No linkTable 4-1 LANVIEW LEDs Continued BPDUs being sent if STARefer to the MATRIX E7 Series and 4.2 TROUBLESHOOTING CHECKLISTSmartSwitch 6000 Series Modules Local Management User’s Guide for proper setupSmartSwitch 6000 Series Modules Local Management User’s Guide for instructionsRefer to MATRIX E7 Series and SmartSwitch 6000 Series Modules LocalFigure 4-2 RESET Button 4.3 USING THE RESET BUTTONRESET Button Using the RESET Button4-8 Troubleshooting Using the RESET ButtonPhysical SpecificationsI/O Ports Processors/MemoryEnvironmental A.1 COM PORT PINOUT ASSIGNMENTSUL 1950, CSA C22.2 No A.2 REGULATORY COMPLIANCESafety Specifications A-3Page B.1 REQUIRED TOOLS Mode Switch Bank Settings and OptionsB.2 SETTING THE MODE SWITCHES Switch 6 - Forced BootP B.3.1 Locating the FLASH Memory B.3 FLASH MEMORY UPGRADEB.3.2 Installing the FLASH Memory Figure B-4 HSIM and VHSIM Connector Locations B.4 INSTALLING OPTIONAL HSIM OR VHSIM INTERFACE MODULESOptional HSIM or VHSIM HSIM/VHSIM Connectors Installing Optional HSIM or VHSIM Interface ModulesNumerics IndexIndex-2