Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks 6H352-25 Installing the Module into the MATRIX E7 Chassis, Installation, 6C107

Models: 6H352-25

1 56

Download 56 pages 21.77 Kb

Page 30

Figure 3-1 Installing the 6H352-25 into the MATRIX E7 Chassis

Installing the Module into the MATRIX E7 Chassis

Figure 3-1 Installing the 6H352-25 into the MATRIX E7 Chassis

			Backplane
			Connectors
	Slot Number
						Plastic Locking Tab
						6C107
1	2	3	4	5	6	7
1	2	3	4	5	FAST ENET	7
					6H352-25
						RESET
						COM
					1X	CPU
						GROUP
						SELECT
					G
					R	GROUPGROUP
					O	GROUPGROUP
					U
					P
					1

11X

13X

G

R

O

U

P

2

23X

			6C407
	AC ON		AC ON
	1		1
	0		0
POWER OK/	FAN	POWER OK/	FAN
REDUNDANCY	STATUS	REDUNDANCY	STATUS
	6C207-1		6C207-1

Metal Back-Panel

Circuit Card

Card Guides

Plastic

Locking Tab

3547_02

3-4Installation

Image 30

Enterasys Networks 6H352-25 Installing the Module into the MATRIX E7 Chassis, Installation, Backplane, Connectors, 6C207-1

Contents

6H352-25 6H352-25 Fast Ethernet Installation GuideRESET COM FAST ENETPage Enterasys Networks, Inc 35 Industrial Way Rochester, NH FCC NOTICE INDUSTRY CANADA NOTICEVCCI NOTICE ENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENT BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCTCAREFULLY READ THIS LICENSE AGREEMENT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU DECLARATION OF CONFORMITY Page INTRODUCTION ContentsABOUT THIS GUIDE ContentsSPECIFICATIONS INSTALLATIONTROUBLESHOOTING MODE SWITCH BANK SETTINGS AND OPTIONSFigures FiguresTables USING THIS GUIDE About This GuideImportant Notice STRUCTURE OF THIS GUIDE MATRIX E7 Overview and Setup Guide6C105 SmartSwitch 6000 Overview and Setup Guide RELATED DOCUMENTSDocument Conventions DOCUMENT CONVENTIONSThe guide uses the following conventions About This GuideGETTING HELP Introduction Important Notice1-2 Introduction RESET COMFigure 1-1 The 6H352-25 Module 6H352-251.3 RUNTIME IP ADDRESS DISCOVERY 1.1 CONNECTIVITY1.2 OPTIONAL HSIMs AND VHSIMs NOTE The 6H352-25 will reboot after RAD is successful1.6 REMOTE MONITORING RMON 1.4 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION1.5 SmartTrunk Half-Duplex/Full-Duplex Auto-Negotiation1.7 BROADCAST SUPPRESSION 1.8 PORT/VLAN REDIRECT FUNCTIONS1.9 TRAFFIC RATE LIMITING 1.11 GARP SWITCH OPERATION 1.10 FLOW CONTROL1.12 802.1 PORT PRIORITY Installation in the SmartSwitch 6000 chassis 1.15 SWITCHING OPTIONSInstallation in the MATRIX E7 Chassis 1.13 DISTRIBUTED CHASSIS MANAGEMENTStandards Compatibility 1.17 LANVIEW DIAGNOSTIC LEDs1.16 STANDARDS COMPATIBILITY 1-8 Introduction2.1 SmartTrunk FEATURE Network Requirements2.2 10BASE-T NETWORK 2.3 100BASE-TX NETWORK 100BASE-TX Network2-2 Network Requirements Installation 3.2 INSTALLING OPTIONAL HSIM, VHSIM, OR FLASH MEMORY UPGRADE 3.1 UNPACKING THE 6H352-253.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS 3-4 Installation Installing the Module into the MATRIX E7 ChassisFigure 3-1 Installing the 6H352-25 into the MATRIX E7 Chassis Connectors3.4 INSTALLING THE MODULE INTO THE SmartSwitch CHASSIS 3-6 Installation Installing the Module into the SmartSwitch ChassisFigure 3-2 Installing the 6H352-25 into the SmartSwitch 6000 Chassis Connector3.5 CONNECTING TO THE NETWORK Group Select Button RX LED TX LED Figure 3-3 Connecting a Twisted Pair Segment to the 6H352-25Figure 3-4 Crossover Cable RJ45 Pinouts Figure 3-5 Straight-Through Cable RJ45 PinoutsRJ45 to RJ45 3.6 COMPLETING THE INSTALLATION Completing the Installation3-10 Installation Troubleshooting 4.1 USING LANVIEWViewing Receive and Transmit Activity GROUP SELECT GROUP Using LANVIEW4-2 Troubleshooting Figure 4-1 LANVIEW LEDsNo link Table 4-1 LANVIEW LEDsBPDUs being sent if STA Table 4-1 LANVIEW LEDs ContinuedManagement User’s Guide for proper setup 4.2 TROUBLESHOOTING CHECKLISTSmartSwitch 6000 Series Modules Local Refer to the MATRIX E7 Series andSmartSwitch 6000 Series Modules Local Management User’s Guide for instructionsRefer to MATRIX E7 Series and SmartSwitch 6000 Series Modules LocalUsing the RESET Button 4.3 USING THE RESET BUTTONRESET Button Figure 4-2 RESET ButtonUsing the RESET Button 4-8 TroubleshootingProcessors/Memory SpecificationsI/O Ports PhysicalA.1 COM PORT PINOUT ASSIGNMENTS EnvironmentalSpecifications A-3 A.2 REGULATORY COMPLIANCESafety UL 1950, CSA C22.2 NoPage Mode Switch Bank Settings and Options B.1 REQUIRED TOOLSB.2 SETTING THE MODE SWITCHES Switch 6 - Forced BootP B.3 FLASH MEMORY UPGRADE B.3.1 Locating the FLASH MemoryB.3.2 Installing the FLASH Memory Installing Optional HSIM or VHSIM Interface Modules B.4 INSTALLING OPTIONAL HSIM OR VHSIM INTERFACE MODULESOptional HSIM or VHSIM HSIM/VHSIM Connectors Figure B-4 HSIM and VHSIM Connector LocationsIndex NumericsIndex-2