Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks 6H352-25 manual Mode Switch Bank Settings and Options, B.1 REQUIRED TOOLS

Models: 6H352-25

1 56

Download 56 pages 21.77 Kb

Page 49

Mode Switch Bank Settings and Options

B

Mode Switch Bank Settings and Options

This appendix covers the following items:

•Required tools (Section B.1)

•Locations, functions, and settings for the mode switches (Section B.2)

•Upgrading FLASH memory (Section B.3)

B.1 REQUIRED TOOLS

Use the following tools to perform the procedures provided in this appendix:

•Antistatic wrist strap

•Phillips screwdriver

CAUTION: An antistatic wrist strap is required (provided with the module) to perform the procedures in this appendix. Use the antistatic wrist strap when performing any of the procedures in this appendix to minimize ESD damage to the devices involved.

Mode Switch Bank Settings and Options

B-1

Image 49

Enterasys Networks 6H352-25 manual Mode Switch Bank Settings and Options, B.1 REQUIRED TOOLS

Contents

RESET COM 6H352-25 Fast Ethernet Installation Guide6H352-25 FAST ENETPage Enterasys Networks, Inc 35 Industrial Way Rochester, NH INDUSTRY CANADA NOTICE FCC NOTICEVCCI NOTICE BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT ENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENTCAREFULLY READ THIS LICENSE AGREEMENT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU DECLARATION OF CONFORMITY Page ABOUT THIS GUIDE ContentsINTRODUCTION ContentsTROUBLESHOOTING INSTALLATIONSPECIFICATIONS MODE SWITCH BANK SETTINGS AND OPTIONSFigures FiguresTables About This Guide USING THIS GUIDEImportant Notice 6C105 SmartSwitch 6000 Overview and Setup Guide MATRIX E7 Overview and Setup GuideSTRUCTURE OF THIS GUIDE RELATED DOCUMENTSThe guide uses the following conventions DOCUMENT CONVENTIONSDocument Conventions About This GuideGETTING HELP Important Notice IntroductionFigure 1-1 The 6H352-25 Module RESET COM1-2 Introduction 6H352-251.2 OPTIONAL HSIMs AND VHSIMs 1.1 CONNECTIVITY1.3 RUNTIME IP ADDRESS DISCOVERY NOTE The 6H352-25 will reboot after RAD is successful1.5 SmartTrunk 1.4 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION1.6 REMOTE MONITORING RMON Half-Duplex/Full-Duplex Auto-Negotiation1.8 PORT/VLAN REDIRECT FUNCTIONS 1.7 BROADCAST SUPPRESSION1.9 TRAFFIC RATE LIMITING 1.10 FLOW CONTROL 1.11 GARP SWITCH OPERATION1.12 802.1 PORT PRIORITY Installation in the MATRIX E7 Chassis 1.15 SWITCHING OPTIONSInstallation in the SmartSwitch 6000 chassis 1.13 DISTRIBUTED CHASSIS MANAGEMENT1.16 STANDARDS COMPATIBILITY 1.17 LANVIEW DIAGNOSTIC LEDsStandards Compatibility 1-8 IntroductionNetwork Requirements 2.1 SmartTrunk FEATURE2.2 10BASE-T NETWORK 100BASE-TX Network 2.3 100BASE-TX NETWORK2-2 Network Requirements Installation 3.1 UNPACKING THE 6H352-25 3.2 INSTALLING OPTIONAL HSIM, VHSIM, OR FLASH MEMORY UPGRADE3.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS Figure 3-1 Installing the 6H352-25 into the MATRIX E7 Chassis Installing the Module into the MATRIX E7 Chassis3-4 Installation Connectors3.4 INSTALLING THE MODULE INTO THE SmartSwitch CHASSIS Figure 3-2 Installing the 6H352-25 into the SmartSwitch 6000 Chassis Installing the Module into the SmartSwitch Chassis3-6 Installation Connector3.5 CONNECTING TO THE NETWORK Figure 3-3 Connecting a Twisted Pair Segment to the 6H352-25 Group Select Button RX LED TX LEDFigure 3-5 Straight-Through Cable RJ45 Pinouts Figure 3-4 Crossover Cable RJ45 PinoutsRJ45 to RJ45 Completing the Installation 3.6 COMPLETING THE INSTALLATION3-10 Installation 4.1 USING LANVIEW TroubleshootingViewing Receive and Transmit Activity 4-2 Troubleshooting Using LANVIEWGROUP SELECT GROUP Figure 4-1 LANVIEW LEDsTable 4-1 LANVIEW LEDs No linkTable 4-1 LANVIEW LEDs Continued BPDUs being sent if STASmartSwitch 6000 Series Modules Local 4.2 TROUBLESHOOTING CHECKLISTManagement User’s Guide for proper setup Refer to the MATRIX E7 Series andRefer to MATRIX E7 Series and Management User’s Guide for instructionsSmartSwitch 6000 Series Modules Local SmartSwitch 6000 Series Modules LocalRESET Button 4.3 USING THE RESET BUTTONUsing the RESET Button Figure 4-2 RESET Button4-8 Troubleshooting Using the RESET ButtonI/O Ports SpecificationsProcessors/Memory PhysicalEnvironmental A.1 COM PORT PINOUT ASSIGNMENTSSafety A.2 REGULATORY COMPLIANCESpecifications A-3 UL 1950, CSA C22.2 NoPage B.1 REQUIRED TOOLS Mode Switch Bank Settings and OptionsB.2 SETTING THE MODE SWITCHES Switch 6 - Forced BootP B.3.1 Locating the FLASH Memory B.3 FLASH MEMORY UPGRADEB.3.2 Installing the FLASH Memory Optional HSIM or VHSIM HSIM/VHSIM Connectors B.4 INSTALLING OPTIONAL HSIM OR VHSIM INTERFACE MODULESInstalling Optional HSIM or VHSIM Interface Modules Figure B-4 HSIM and VHSIM Connector LocationsNumerics IndexIndex-2