Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks 6H352-25 manual B.3.2 Installing the FLASH Memory

Models: 6H352-25

1 56

Download 56 pages 21.77 Kb

Page 53

B.3.2 Installing the FLASH Memory

FLASH Memory Upgrade

B.3.2 Installing the FLASH Memory

CAUTION: Observe all antistatic precautions when handling sensitive electronic equipment.

To install a FLASH memory, refer to Figure B-3and proceed as follows:

1.With the FLASH memory oriented as shown in Figure B-3, insert the FLASH memory down between the connector.

2.Pivot the FLASH memory downward so the connector clips align with the two side notches of the FLASH memory and the connector clips lock the FLASH memory into place.

Figure B-3 Installing the FLASH Memory

2

FLASH

Connector Clip

1

Clip

3547_11

Mode Switch Bank Settings and Options

B-5

Image 53

Enterasys Networks 6H352-25 manual B.3.2 Installing the FLASH Memory

Contents

RESET COM 6H352-25 Fast Ethernet Installation Guide6H352-25 FAST ENETPage Enterasys Networks, Inc 35 Industrial Way Rochester, NH VCCI NOTICE FCC NOTICEINDUSTRY CANADA NOTICE CAREFULLY READ THIS LICENSE AGREEMENT ENTERASYS NETWORKS, INC PROGRAM LICENSE AGREEMENTBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT 7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL ENTERASYS OR ITS SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS ARISING OUT OF THE USE OR INABILITY TO USE THIS ENTERASYS PRODUCT, EVEN IF ENTERASYS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU DECLARATION OF CONFORMITY Page ABOUT THIS GUIDE ContentsINTRODUCTION ContentsTROUBLESHOOTING INSTALLATIONSPECIFICATIONS MODE SWITCH BANK SETTINGS AND OPTIONSFigures FiguresTables Important Notice USING THIS GUIDEAbout This Guide 6C105 SmartSwitch 6000 Overview and Setup Guide MATRIX E7 Overview and Setup GuideSTRUCTURE OF THIS GUIDE RELATED DOCUMENTSThe guide uses the following conventions DOCUMENT CONVENTIONSDocument Conventions About This GuideGETTING HELP Important Notice IntroductionFigure 1-1 The 6H352-25 Module RESET COM1-2 Introduction 6H352-251.2 OPTIONAL HSIMs AND VHSIMs 1.1 CONNECTIVITY1.3 RUNTIME IP ADDRESS DISCOVERY NOTE The 6H352-25 will reboot after RAD is successful1.5 SmartTrunk 1.4 HALF-DUPLEX/FULL-DUPLEX AUTO-NEGOTIATION1.6 REMOTE MONITORING RMON Half-Duplex/Full-Duplex Auto-Negotiation1.9 TRAFFIC RATE LIMITING 1.7 BROADCAST SUPPRESSION1.8 PORT/VLAN REDIRECT FUNCTIONS 1.12 802.1 PORT PRIORITY 1.11 GARP SWITCH OPERATION1.10 FLOW CONTROL Installation in the MATRIX E7 Chassis 1.15 SWITCHING OPTIONSInstallation in the SmartSwitch 6000 chassis 1.13 DISTRIBUTED CHASSIS MANAGEMENT1.16 STANDARDS COMPATIBILITY 1.17 LANVIEW DIAGNOSTIC LEDsStandards Compatibility 1-8 Introduction2.2 10BASE-T NETWORK 2.1 SmartTrunk FEATURENetwork Requirements 2-2 Network Requirements 2.3 100BASE-TX NETWORK100BASE-TX Network Installation 3.1 UNPACKING THE 6H352-25 3.2 INSTALLING OPTIONAL HSIM, VHSIM, OR FLASH MEMORY UPGRADE3.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSIS Figure 3-1 Installing the 6H352-25 into the MATRIX E7 Chassis Installing the Module into the MATRIX E7 Chassis3-4 Installation Connectors3.4 INSTALLING THE MODULE INTO THE SmartSwitch CHASSIS Figure 3-2 Installing the 6H352-25 into the SmartSwitch 6000 Chassis Installing the Module into the SmartSwitch Chassis3-6 Installation Connector3.5 CONNECTING TO THE NETWORK Figure 3-3 Connecting a Twisted Pair Segment to the 6H352-25 Group Select Button RX LED TX LEDRJ45 to RJ45 Figure 3-4 Crossover Cable RJ45 PinoutsFigure 3-5 Straight-Through Cable RJ45 Pinouts 3-10 Installation 3.6 COMPLETING THE INSTALLATIONCompleting the Installation Viewing Receive and Transmit Activity Troubleshooting4.1 USING LANVIEW 4-2 Troubleshooting Using LANVIEWGROUP SELECT GROUP Figure 4-1 LANVIEW LEDsTable 4-1 LANVIEW LEDs No linkTable 4-1 LANVIEW LEDs Continued BPDUs being sent if STASmartSwitch 6000 Series Modules Local 4.2 TROUBLESHOOTING CHECKLISTManagement User’s Guide for proper setup Refer to the MATRIX E7 Series andRefer to MATRIX E7 Series and Management User’s Guide for instructionsSmartSwitch 6000 Series Modules Local SmartSwitch 6000 Series Modules LocalRESET Button 4.3 USING THE RESET BUTTONUsing the RESET Button Figure 4-2 RESET Button4-8 Troubleshooting Using the RESET ButtonI/O Ports SpecificationsProcessors/Memory PhysicalEnvironmental A.1 COM PORT PINOUT ASSIGNMENTSSafety A.2 REGULATORY COMPLIANCESpecifications A-3 UL 1950, CSA C22.2 NoPage B.1 REQUIRED TOOLS Mode Switch Bank Settings and OptionsB.2 SETTING THE MODE SWITCHES Switch 6 - Forced BootP B.3.1 Locating the FLASH Memory B.3 FLASH MEMORY UPGRADEB.3.2 Installing the FLASH Memory Optional HSIM or VHSIM HSIM/VHSIM Connectors B.4 INSTALLING OPTIONAL HSIM OR VHSIM INTERFACE MODULESInstalling Optional HSIM or VHSIM Interface Modules Figure B-4 HSIM and VHSIM Connector LocationsNumerics IndexIndex-2