Enterasys Networks 7H4385-49 guide

Gaining Access to Memory Modules

Figure B-9 Installing the Network Expansion Module

À

Â

Å

F ENETAST

H7 34 58 94-

Á

OFFLINE/RESET

COM

CPU	OUP SELECT GR
TM G POE M	1 OUPGR	2	3	4	5	6	7
	1	2					8
		2	3				9
			3	4			10
				4			11
							12
1X
1X							X12
	G
	RGOR
		UOPU	P1 1
			P1 1
							11X

6 5 4 3 2 1

-7G A-6MGBIC

1

2

3

4

5

6

14X
13X	24X
RO	26X
G
	UP
	2
	23X
Ä	25X	P	3	36X	38X
		R G
		OU
				35X
					37X	48X
						G
						RO
						UP
						4

PO ---48VWER MAX20AOPTIONALINPUT

Ã

DFE

1	NEM	3	NEM connectors	5	Coverplate screws (2)
2	Front panel	4	Main board connectors	6	Standoff

3.Use two of the saved coverplate screws to fasten the NEM to the DFE module front panel, but do not tighten screws at this time.

4.Insert the saved standoff through the NEM to the standoff on the main board. Screw in the standoff, but do not tighten screws at this time.

5.Tighten the two coverplate screws first, then the standoff.

B-12 Mode Switch Settings and Option Installations

Image 84

Enterasys Networks 7H4385-49 manual Figure B-9 Installing the Network Expansion Module

Contents

Enterasys Matrix Page Page Product Safety Federal Communications Commission FCC NoticeIndustry Canada Notice Class a ITE Notice Clase A. Aviso de ITE Electromagnetic Compatibility EMC Compatibilidad Electromágnetica EMCElektro- magnetische Kompatibilität EMC Supplement to Product Instructions Safety Information Class 1 Laser Transceivers Vcci NoticeBsmi EMC Statement Taiwan Declaration of Conformity USA Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Troubleshooting Appendix a SpecificationsAppendix B Mode Switch Settings and Option Installations Appendix C About PoE Power over Ethernet Figures Tables Xiv About This Guide Who Should Use This GuideImportant Notice How to Use This Guide Related DocumentsFor Refer to Conventions Used in This Guide Following conventions are used in this guide Getting Help Support@enterasys.com Introduction For information about Refer to Overview of DFE-Platinum Series Module Capabilities DFE-Platinum 7H4385-49 PoE Module 7H4385-49 DFE-Platinum Module Switch Configuration Using WebView Switch Configuration Using CLI CommandsConnectivity Management Lanview Diagnostic LEDs Secure Networks Policy Support Network Requirements Link Aggregation Module Placement in a Matrix E7 Chassis FTM Bridge Function and Optional Interface Module10BASE-T Network 100BASE-TX Network 100BASE-TX Network Network Requirements Installation Installation Site Requirement Contents of 7H4385-49 Module Carton QuantityUnpacking the DFE Module Installing Optional Network Expansion Module NEM Backplane Connections and Installation RulesFTM1 and FTM2 Connectivity Module Placement and Installation Rules Matrix E7 Chassis Module PlacementExample 1 -1,A Example 2 -1,B Example 3 -1, CExample 4 -1,D Example 5 -1, E Example 6 -1, F DFE-Platinum Series Hardware Installation Guide To install the 7H4385‐49, refer to ‐2 and proceed as follows DFE-Platinum Series Hardware Installation Guide No bottom connectors in Matrix N7chassis Installing the 7H4385-49 into Matrix N1, N3, or N5 Chassis Installation Installing Module into Matrix N3, N5, or N1 Chassis N3 shown Connecting 48 Vdc Power for PoE Operation Connecting to the Network Connecting UTP Cables to 7H4385-49 Connecting a Twisted Pair Segment with RJ45 Connector Making the UTP Connections RX+ TX+ TX1+ RX1 TX2+ TX3+ RX3 RX2 TX4+ RX4 Verifying PoE Port Status Connecting to COM Port for Local Management What Is NeededConnecting to an IBM PC or Compatible Device Connecting to a VT Series Terminal Parameter Setting Connecting to a Modem 10 Connecting a VT Series Terminal 11 Connecting to a Modem Adapter Wiring and Signal Assignments COM Port Adapter Wiring and Signal Diagram RJ45 Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Completing the Installation Completing the Installation of a New SystemFirst-Time Log-In Using a Console Port Connection 12 Matrix DFE Startup Screen Example N7 Chassis Logging in with an Administratively-Configured User Account Enter Troubleshooting Using LanviewAbout the Management Mgmt LED Viewing the Receive and Transmit Activity Viewing the PoE Port Status LED Color State Recommended Action RX/TX Indications in Standard Mode Amber and Alternating 67% on, 33% RX/TX Troubleshooting Checklist DFE-Platinum Series Configuration Guide Troubleshooting Checklist Problem Possible Cause Recommended Action Overview of DFE Module Shutdown Procedure Recommended Shutdown Procedure Using OFFLINE/RESET Switch OFFLINE/RESET Switch Last Resort Shutdown Procedure Using OFFLINE/RESET Switch Specifications DFE Module SpecificationsTable A-1 7H4385-49 Specifications Processors/Memory Table A-1 7H4385-49 Specifications Physical Table A-2 COM Port Pin Assignments Signal Name Input/OutputCOM Port Pinout Assignments Environmental Regulatory Compliance Table A-3 Compliance Standards Regulatory Compliance Regulatory Compliance Specifications Mode Switch Settings and Option Installations Required Tools Setting the Mode Switches Memory Locations and Replacement Procedures Memory Locations and Replacement Procedures Gaining Access to Memory Modules Gaining Access to Memory Modules Removing the Safety Cover Figure B-3 Removing the Safety Cover Dram Simm Replacement Procedure Removing the Optional Network Expansion Module NEM Removing the Dram Simm Figure B-5 Removing the Existing Dram Simm Installing the Dram Simm Figure B-6 Installing the Dram Simm Dimm Replacement Procedure Removing the Dimm Installing the Network Expansion Module NEM Installing the Dimm Figure B-9 Installing the Network Expansion Module Reinstalling the Safety Cover Figure B-10 Installing the Safety Cover About PoE Power over Ethernet Overview Proprietary PD Detection PoE Port Status LEDs Table C-2 PoE Status LED Indications PoE Port Status Overview About PoE Power over Ethernet Index Numerics Pinout assignments console port A-2