Manuals / Epson / Computer Equipment / All in One Printer

Epson C120, C110 manual Again, press the ink out button on the front of the printer

Models: C120 C110

1 55

Download 55 pages 50.61 Kb

Page 19

4.Again, press the ink out button on the front of the printer.

Sawgrass Technologies, Inc. ChromaBlast™ Getting Started Guide for the EPSON Stylus C120/C110

4.Again, press the ink out button on the front of the printer.

5.The printer will begin to reset and recharge. After the printer has completed the resetting activity, the orange light will turn off. At this point the bulk ink system has been successfully reset and the printer is again ready for use.

17

Image 19

Epson C120, C110 manual Again, press the ink out button on the front of the printer

Contents

Getting Started Guide v1.0For EPSON Stylus C120/C110 ChromaBlastPage Getting Started Guide for the ChromaBlastTMEPSON Stylus C120/C110 This product is for commercial use only IMPORTANT – READ CAREFULLY2. LIMITATIONS ON REVERSE ENGINEERING IMPORTANT – READ CAREFULLYSoftware PRODUCT LICENSE are trademarks of Sawgrass Technologies, Inc How to get service Sawgrass Technologies, Inc. Limited WarrantyWhat Is Covered Length of Warranty CoverageTable of Contents Introduction About this Document Components Quick Connect II Set-upfor the C120/C1103.Slowly extract the plunger. Ink will start to flow through the tubing into the damper. Continue extracting the plunger until ink begins to flow into the tip of the syringe. Note You may have to repeat this process twice to complete the priming of each ink damper. Repeat this process for the other three ink bags Printer Set-upfor the C120/C110 5.Remove the printer cover panel by inserting a flat head screwdriver between the panel and the printer. Gently push the cover panel loose 9.Install the plastic support arm. First remove the adhesive backing on the back of the plastic arm Tips Chip Reset Instructions 4.Again, press the ink out button on the front of the printer Installing ChromaBlast Cartridges 5.Open the cartridge cover 11.Close the printer cover Replacing an Empty Cartridge 9.Place the new ink cartridge PRINTING Printing and Heat Transfer InstructionsHEAT PRESS SETTINGS RECOMMENDED APPLICATIONSFor Epson Stylus C120/C110 For distribution with ChromaBlast onlyNOT FOR RESALE ChromaBlast Driver User GuideSystem Requirements ChromaBlast Driver IntroductionMinimum Hardware Quick Start Setup Instructions - Windows XP / VistaStep By Step Installation Product Overviewto be installed before proceeding with the installation of the PowerDriver software. If you have already installed this OEM driver than click Next to proceed Page Technologies, Inc. directly Page Page From the Windows Desktop Using ChromaBlast Driver in Windows XP / VistaSetting ChromaBlast Driver printer properties Quick Start Example Corel DrawThere are three main property groups ChromaBlast Driver Properties OverviewOverview Group 1 - ConfigurationGroup 2 - Color Options Color Correction SettingsOutput Options ColorSure OptionsResources Group 3 - Printer OptionsHost Machine Server CorelDraw version 10, 11 and Color Setup CorelDraw version Adobe Photoshop 7, CS, and CS2To Print I. Introduction Appendix C Using ColorSure and Custom PaletteII.Printing the ColorSure Palette HINT III.Designing Your ArtworkHow to use Color Finder IV. Using Color FinderColor Finder Palette with two Step Colors Custom Palette UtilityColor Finder Palette with three Step Colors V.The Custom Palette How to use Custom Palette VI. Adding Swatches to your Application Palette Media Storage Supplies & EquipmentOperating Conditions Ink StorageThe colors in my transferred image are incorrect TroubleshootingMy printout gets cut off on the bottom or side My image has gaps or bands present My image looks good but it washes outColors are light and splotchy My image looks blurreda Nozzle Check from the Utility tab of your printer driver. For further instructions, see the EPSON Stylus C120/C110 Printer User’s Guide Project Cotton Technical Support