Turning On the Power and Projecting Images
Procedure
1 |
|
|
| Turn on the power for all equipment |
|
|
| connected to the projector. | |
|
|
|
| For a video source, press the [Play] button at the |
|
|
|
| video source to start playback if necessary. Check |
|
|
|
| that the Power indicator has stopped flashing and |
|
|
|
| lights orange. |
2 | Changes from flashing to lit green |
| Press the [Power] button on either the | |
|
|
| projector's control panel or the remote | |
|
|
|
| control to turn on the power for the |
|
|
| Power | projector. |
|
|
| The Power indicator flashes green, and after a | |
|
|
|
| |
| Computer | short period it stops flashing and projection starts. | ||
|
|
|
| |
| Menu | A/V Mute | Freeze | Wait until the Power indicator lights green (it |
normally takes about 40 seconds to change). | |
Enter |
|
Remote control |
|
The projector's control panel and remote control buttons cannot be operated while the
Power indicator is flashing green.
Depending on the settings, the message
Msg. (p.25)
| If more than one signal source has been connected, use the projector's control | ||||
3 panel or the remote control to select a port, while referring to the following table. | |||||
| Port | Button to press | Display at top right of | ||
|
|
|
| screen | |
| Projector | Remote control |
| ||
|
|
| |||
|
|
|
|
| |
| Computer/ |
|
| Computer * | |
| The image source | [Computer] | YCbCr | * | |
| Component Video | ||||
|
| YPbPr | * | ||
|
| changes each time |
| ||
|
|
|
|
| |
| [Source] is pressed. |
| |||
|
|
|
|
| |
| Video |
| Video |
| |
|
|
|
| ||
|
|
|
|
|
|
*The message displayed depends on which Input Signal option has been selected in the Video menu.
•If only one signal source has been connected, that source will be projected without any
buttons being pressed.
• If the
• | If a laptop computer or a computer with an LCD screen has been connected to the | |||||||
| projector, the images may not be projected immediately. After making the connections, | |||||||
| check that the computer has been set up to output signals externally. The following table | |||||||
| shows examples of how to toggle output settings. For details, refer to the section of the | |||||||
| documentation provided with your computer under a heading such as “External output,” | |||||||
| “Connecting an external monitor” or something similar. |
|
| |||||
|
|
|
|
|
|
|
|
|
|
| NEC | Panasonic | Toshiba | IBM | Sony | Fujitsu | Macintosh |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| After startup, change the |
|
| [Fn]+[F3] | [Fn]+[F3] | [Fn]+[F5] | [Fn]+[F7] | [Fn]+[F7] | [Fn]+[F10] | Control Panel adjustments |
|
|
|
|
|
|
|
| so that Mirroring is active |
|
|
|
|
|
|
|
|
|
• | If the same still picture is projected for a long period of time, the projected image may | |||||||
| become burned into the computer screen. You should avoid leaving the same image | |||||||
| displayed for long periods. |
|
|
|
| |||
Basic Operations
9