Manuals / Extron electronic / Home Audio / Speaker

Extron electronic CS 120P, CS 26T manual Application Example, Extron CS 1226T

Models: CS 1226T CS 26T CS 120P

1 33

Download 33 pages 50.04 Kb

Page 8

Application Example

•Selectable taps — The rotary tap selector switch, located behind the grille, sets the speaker to operate in either 8-ohm direct or 70 volt /100 volt operation with 16, 8, 4, 2, and 1 watt taps.

•Magnetic grille — Magnets spaced around the grille edge enable it to be easily attached and to remain firmly in place.

Application Example

The illustration below is one example of configuring a system using the CS 1226T.

Desk Microphones

INPUT

AUDIO

OUTPUT

I

N

P

U

T

Extron

IN1508

Scaling Presentation

Switcher

PC

	Extron
	TLP 700TV	Ethernet
	7" TouchLink	Ethernet
	7" TouchLink
	Tabletop
	Touchpanel
		TCP/IP
		Network
	Extron
Laptop	IPL 250
Laptop	IP Link Control
	IP Link Control
	Processor

∞

∞

∞

Extron

XPA 2003C 70V

Combo Power Amplier

Extron

DMP 64

Digital Matrix Processor

64

	DMP
LAN	RESET

I/O

INPUTS	U
MIC/LINE	O
MIC/LINE	P
	T
	U
	T
	S

POWER

RS-232

Extron

SI 26

Surface-Mount Speakers

Extron

CS 1226T

SpeedMount Ceiling Speaker System

Figure 1. Application Diagram of a CS 1226T Installation

CS 26T and CS 120P User Guide • Introduction

2

Image 8

Extron electronic CS 120P, CS 26T manual Application Example, Extron CS 1226T

Contents

CS 26T and CS 120P User GuideSpeakers CS 1226T SpeedMount Ceiling Speaker SystemSafety Instructions Safety Instructions EnglishChinese Simplified（简体中文） Instructions de sécurité FrançaisFCC Class A Notice Guide” on the Extron websiteCopyright TrademarksNotifications Specifications AvailabilityConventions Used in this Guide Contents CS 26T and CS 120P User Guide Contents Features About this Guide Overview FeaturesIntroduction About this GuideApplication Example Extron CS 1226TInstallation Installation ConsiderationsInstallation Configurations Installation ConsiderationsInstalling the CS 1226T System - Single Installer Figure 3. Install the Ceiling Mount Kit Using a flexible conduit 8.Route the cables through the cover plateedges Figure 11. Configuring the Bass Reflex Port Plate Number of Wires per Connection Point Maximum Wire GaugeFigure 12. Wiring a Single Speaker Figure 13. Wiring Multiple Speakers in ParallelWiring Multiple Speakers Using Loop-through Red Wire + from Ampliﬁer Black Wire -from Ampliﬁer2 by 4 Ceiling Tile 4 Pole Connector Ampliﬁer19.Mount the CS 26T see figure Figure 21. Attaching Secondary Support Lines Figure 22. Adjusting the Rotary Tap Selector Figure 23. Installing the Speaker GrilleFigure 24. Grid Face Example Figure 26. Removing the Cover Plate Using a flexible conduit Using speaker wires without a conduit7.Route the cables through the cover plate Figure 28. Routing the Cables Without a Conduitedges Figure 32. Attaching Secondary Support Lines CS 120P Number of Wires per Maximum WireFigure 33. Wiring a Single Speaker Figure 34. Wiring Multiple Speakers in ParallelWiring Multiple Speakers Using Loop-through Figure 38. Impedance Test Points - Loop-throughConfiguration 8.Mount the CS 26T see figure Figure 42. Adjusting the Rotary Tap Selector Figure 43. Installing the Speaker GrilleInstalling the CS 120P in a Hard Ceiling Extron Warranty