Simple Instruction Set Control
Symbols
Symbols (values), defined starting below, are used throughout the discussions of the
] = CR/LF (carriage return and line feed) (hex 0D 0A)
}= Carriage return (no line feed, hex 0D)
= Pipe (can be used interchangeably with the } character)
•= Space character
E = Escape key (hex 1B)
W = Can be used interchangeably with the E character
X! | = | Image file name | Image name with file extension (*.bmp or *.jpg) | ||||
|
|
| (Up to 240 alphanumeric characters with no spaces) | ||||
X@ | = | Status: |
|
|
|
|
|
|
| On / off | 0 | = off | 1 = on |
|
|
|
| Busy | 0 | = free | 1 = busy |
| |
|
| Cut / dissolve | 0 | = cut | 1 = dissolve |
| |
|
| 0 | = | 1 = no |
| ||
X# | = | Time | 00 – 50 (0.0 to 5.0 seconds) for RGB delay and dissolve duration | ||||
|
|
| 000 – 300 seconds for slide show interval |
| |||
X$ | = | 0 | = off | 2 | = on / still |
| |
|
|
| 1 | = off / show | 3 | = on / show |
|
X% | = | Resolution | 0 | = 640 x 480 | 10 | = 1366 x 768 |
|
|
|
| 1 | = 600 x 600 | 11 | = 1365 x 1024 |
|
|
|
| 2 | = 852 x 480 | 12 | = 1400 x 1050 |
|
|
|
| 3 | = 1024 x 768 | 13 | = 480p |
|
|
|
| 4= 1024 x 852 | 14 | = 576p |
| |
|
|
| 5 | = 1024 x 1024 | 15 | = 720p |
|
|
|
| 6 | = 1280 x 768 | 16 | = 1080i |
|
|
|
| 7 | = 1280 x 1024 | 17 | = 1080p |
|
|
|
| 8 | = 1360 x 765 | 18 | = 1280 x 800 |
|
|
|
| 9 | = 1365 x 768 | 19 | = 1440 x 900 |
|
X^ | = | Refresh rate | 0 | = 50 Hz | 3 | = 96 Hz |
|
|
|
| 1 | = 60 Hz | 4 | = 100 Hz |
|
|
|
| 2 | = 72 Hz | 5 | = 120 Hz |
|
X& | = Sync format | 0 | = RGBHV | 1 | = RGBS |
| |
X* | = | Sync polarity | 0 | = | 2 | = H+ / V– |
|
|
|
| 1 | = | 3 | = H+ / V+ |
|
X( | = | Front panel Lock mode | 0 | = unlock | 1 | = partial lock | 2 = complete lock |
X1) | = | Event number | 00 through 99 |
|
|
| |
X1! | = | Event buffer | 0 | = Receive | 1 | = User | 2 = NVRAM |
X1@ | = | Even buffer offset | 00 through maximum buffer size |
| |||
X1# = | Event data size | b = bit | S = short (16 bits) |
| |||
|
|
| B = byte | L = long (32 bits) |
|
NOTE: The X1# parameter is case sensitive.
X1$ = ASCII digits representing the numeric value of the data element read from the event buffer (leading zeroes are suppressed)
X1% = Event status fieldsEvent type Event state Event paused Error status RcvBuff_startptr RcvBuff_endptr UsrBuff_Startptr UsBuff_endptr
GSS 100 Graphic Still Store • Programming Guide 18