Manuals / Brands / Computer Equipment / Switch / Extron electronic / Computer Equipment / Switch

Extron electronic SVS 100 Executive Mode, System Reset, Advanced Menus

1 48

Download 48 pages, 2.09 Mb

SVS 100 Operation

SYSTEM

RESET

3-7

X-MODE

DISABLED

X-MODE

ENABLED

Executive Mode

The Executive mode allows all front panel controls to be disabled, except for

the Input buttons. Pressing the Top and Bottom Blanking buttons

simultaneously for two seconds will enable the Executive mode. While in

the Executive mode, the RS-232/RS-422 port is still active and commands

can still be issued to the SVS 100 using the Simple Instruction Set (see

chapter 5, Serial Communication).

The Executive mode may be disabled by pressing

the Top and Bottom Blanking buttons

simultaneously for two seconds. The Executive

mode may also be enabled/disabled through the

RS-232/RS-422 port. The LCD will display

whether the Executive mode has been enabled or

disabled.

System Reset

To reset the entire SVS 100 to factory default

settings, disconnect and reconnect the AC power

cord to the SVS 100 while pressing down the Audio

button. The LCD will display a system reset menu.

Advanced Menus

The Advanced menus of the SVS 100 offers menu control of output video

type, Demo mode, input video type, and audio switching. To display the

Advanced menus, simultaneously press the three Effects buttons (effect,

transition, and duration) and follow the menus below.

Output video type

After initially pressing the three Effects

buttons (as previously described), select

the desired video output type by rotating

the encoder knob. The choices are NTSC

or PAL. If no button is pressed within 8

seconds, the SVS 100 exits the Advanced

menus.

Demo mode After selecting an output video type (as

previously described), the Demo mode may

be selected by pressing the Audio button.

The Demo mode will output a continuous

random selection of the four inputs, one-at-

a-time, in 1-second, 30-second, or 60-second

intervals. Press the Audio button and rotate

the encoder knob to either select an interval

or select Off to disable the Demo mode. If no

button is pressed within 8 seconds while

Demo mode is Off, the SVS 100 exits the

Advanced menus.

OUTPUT

NTSC

OUTPUT

PAL

DEMO

60 SEC

DEMO

1 SEC

DEMO

30 SEC

DEMO

OFF

Contents

Main Precautions Caution Warning Attention Avertissement Quick Start SVS 100 Installation Rack or Table/Wall Mounting Connecting the SVS 100 Step 1 Front Panel Operation i SVS 100 Table of Contents Table of Contents Chapter 2 Installation Mounting the SVS 100 Cabling and Rear Panel Views Genlock and Vertical Interval Switching Table of Contents, contd Chapter 5 Serial Communication Appendix Reference Information Page Introduction SVS 100 Introduction 1-2 About the SVS 100 VSC 150 SVS 100 Features 1-3 Page Page Installation Mounting the SVS 100 2-2 or Table or wall mounting Cabling and Rear Panel Views Power connection Video input and output connections Audio input and output connections 2-4 SVS 100 Installation 2-5 Genlock connections RS-232/RS-422 connection Genlock and Vertical Interval Switching 2-6 Genlock setup SVS 100 Installation 2-7 Oscilloscope displays 2-8 +40 -40 A1 A2 A3 B1 B2 B3 Figure 2-9 Vectorscope screen during color subcarrier phase adjustment Page Operation SVS 100 Operation3-2 Front Panel Controls and Indicators Input selection controls and indicators SVS 100 Operation 3-3 Effects controls and indicators + Table A Effect Menus 3-4 Table E Duration Menus Table C Transition Menus Table D Transition Menus EFFECT TRANSITION DURATION SVS 100 Operation 3-5 Genlock controls and indicators Picture controls and indicators 3-6 Audio button Encoder knob 3-7 Executive Mode System Reset Advanced Menus Output video type Demo mode 3-8 Input video type Audio switching method VCR mode SVS 100 Operation 3-9 Optimizing the Video and Audio Inputs Page Page Windows-based Control Program 4-2 SVS 100 Windows-based Control Program Installing the Windows-based Control Software Using the Software SVS 100 Windows-based Control Program 4-3 Page Page Serial Communication Remote Control Port (RS-232/RS-422) Host-to-SVS 100 Communication SVS 100-initiated messages SVS 100 Serial Communication 5-3 Symbol definitions: Effect type Transition list Using the command/response table SVS 100 Serial Communication Serial Communication, contd Figure 5-1 ASCII-to-hexadecimal conversion table 5-4 COMMAND/RESPONSE TABLE COMMAND ASCII RESPONSE DESCRIPTION Input Selection Page Serial Communication, contd Example responses to commands SVS 100 error responses Page Reference Information A-2 Special Applications Saving and Recalling Input Configuration Presets SVS 100 Appendix A-3 Configuring the SVS 100 for RS-422 Removing the top cover Remove the four #8 screws each side and bracket A-4 Reference Information, contd Relocating the ribbon cable and setting the jumper Replacing the top cover J23 Page A-6 Specifications SVS 100 Video input and loopout Video output Audio input Audio throughput General Specifications are subject to change without notice. Page FCC Class A Notice Extrons Warranty 2000 Extron Electronics. All rights reserved.