Fluke 1522 - page 25

computer and written to a file quickly.These items must be purchased sepa-

rately.

LogWare Software-TheLogWare softwareare data acquisition software

packages thatcan be used with your thermometer to collect and graph data. The

softwarealso allows the user to download data logged from the instrument's

memory to a computer and access tosome of the instrument's features.

INFO-CON DownloadAdapter - The Model 2372 INFO-CON download

adapter andModel 9972 INFO-CON Download Adapter software can be used

to program an INFO-CONconnector with new probe calibration coefficients

withoutusing the thermometer readout. The Model 2372 INFO-CON Down-

load Adapter has a 9-pin serial cable that connects to a serial (COM) port on a

PC. The INFO-CON DownloadAdapter software can then be used to read,

edit, and write changes to the INFO-CON connector.

Carrying Cases - There are twotypes of cases available for your 1522 ther-

mometer readout. TheModel 9318 case is a hard case for carrying thether-

mometer readoutand a 12" probe. The Model9321 caseis a soft case with a

beltclip and a probe slot.

23

5 Parts and Controls

Accessories

Figure4 InfraredDongle

Contents

Main Page Table of Contents 7 Display Functions. . . . . . . . . . . . . . . . . . . . . . . . . 31 8 Communications Interface. . . . . . . . . . . . . . . . . . . . 47 Page Figures and Tables 1 Before You Start 1.1 Symbols Used 1.2 Safety Information 1.2.1 WARNINGS 1.2.2 CAUTIONS 1.3 Authorized Service Centers Page 2 Introduction 3 Specifications and Environmental Conditions 3.1 Specifications 9 3 Specifications and Environmental Conditions Specifications 3.2 Environmental Conditions 3.3 Warranty Page 4 Quick Start 4.1 Unpacking 4.2 Use Proper Care with the 1522 and Accessories 4.3 Learn About the Features and Components 4.4 Connect the Probe 4.5 Connect the Power Source 4.6 Switch the Power On 4.7 Measure Temperature Page Page Page 5.2 Top and Side View 5.3 Back View 5.4 Internal Features 5.5 Accessories Page Page 6 General Operation 6.1 Battery 6.2 DC Power Source + 6.3 Power Button 6.4 Display and Backlight 6.5 Probe 6.6 INFO-CON Connector C1 and P1 terminalsand the other single wire to the C2 and P2 terminals (which areshorted together). 1522 Handheld Thermometer Readout Figure7 Probe Wiring Diagrams Short Two-wire Connection 7 Display Functions Each of these operating modes is described in the sections that follow. 7.1 Blank Mode This mode is identified by Blank that temporarily appears on the display. 7.2 Min/Max Mode 7.3 Demand Logging 7.3.1 Demand Log Label and Data Storage 7.3.2 Dump Data? 7.3.3 Clear Log? 7.4 Auto Logging 7.4.1 Clear Autolog? 7.4.2 Log Rate 7.4.3 Autolog Label 7.4.4 Autologged Data Storage 7.4.5 Dump Data? 7.5 Delta(x) Mode 7.6 Units 7.7 Rate 7.8 Resolution 7.9 CAL MODE Page 7.9.1 Mtr Due 7.9.2 Prb Due 7.9.3 Time 7.9.4 Passcode 7.9.5 Date 7.9.6 Probe Lock 7.9.7 Prb # 7.9.8 Prb Type 7.9.9 ITS-90 Page 7.9.10 IEC751 7.9.11 CVD 7.9.12 YSI-400 7.9.13 THERM 7.9.14 Probe Wires 7.9.15 PCal 7.9.16 PDue 7.9.17 Digital Filter 7.9.18 MCal 7.9.19 MDue 7.9.20 CAL1 and CAL2 8 Communications Interface 8.1 RS-232 Connection 8.2 Communication Command List 8.2.1 Primary Commands The followinggroup of commands read or set various functions. n 49 8 Communications Interface Communication Command List 8.2.2 Calibration Commands 51 8 Communications Interface Communication Command List 9 Calibration 9.1 Required Equipment 9.2 Calibration Procedure Page 10 Maintenance 11 Troubleshooting 11.1 An Error Message Is Displayed The followingtable lists possible error messages, their causes, and suggested actions. 57 11 Troubleshooting An Error Message Is Displayed 11.2 Downloading Autologged Data 11.3 Placement of Infrared Dongle for IR Data Transfer 11.4 CE Comments 11.4.1 EMC Directive 11.4.2 Low Voltage Directive (Safety)