Fluke 9150 3.3 Warranty

3.3 Warranty

FlukeCorporation, Hart Scientific Division (Hart) warrants this product to be

free from defectsin material and workmanship under normal use and service

for a periodas stated in our current product catalog from the date of shipment.

This warrantyextends only to the original purchaser and shall not apply to any

product which,in Hart's sole opinion, has been subject to misuse, alteration,

abuseor abnormal conditions of operation or handling.

Softwareis warranted to operate in accordance with its programmed instruc-

tionson appropriateHart products. It is not warranted to be error free.

Hart's obligation under this warranty islimited to repair or replacement of a

product whichis returned to Hart within the warranty period and is determined,

upon examinationby Hart, to be defective. If Hart determines that the defect or

malfunction has been caused by misuse,alteration, abuse or abnormal condi-

tionsor operationor handling,Hart will repair the product and bill the pur-

chaser for the reasonablecost of repair.

Toexercise this warranty, the purchaser must forward the product after calling

or writing an Authorized Service Center (see Section 1.3). The service centers

assume NO risk for in-transit damage.

THE FOREGOING WARRANTYIS PURCHASER'S SOLE AND EXCLU-

SIVE REMEDYAND IS IN LIEU OF ALL OTHER WARRANTIES, EX-

PRESS OR IMPLIED, INCLUDING BUTNOT LIMITED TO ANY

IMPLIED WARRANTYOR MERCHANTABILITY,OR FITNESS FOR ANY

PARTICULARPURPOSE OR USE. HART SHALL NOT BE LIABLE FOR

ANY SPECIAL, INDIRECT,INCIDENTAL, OR CONSEQUENTIAL DAM-

AGESOR LOSS WHETHER IN CONTRACT, TORT,OR OTHERWISE.

9150 Portable Furnace

User’s Guide

10

Contents

Main Page Table of Contents 9 Digital Communication Interface . . . . . . . . . . . . . . . . 37 10 Test Probe Calibration . . . . . . . . . . . . . . . . . . . . . . 43 Page 1 Before You Start 1.1 Symbols Used 1.2 Safety Information 1.2.1 WARNINGS 1.2.2 CAUTIONS 1.3 Authorized Service Centers Page 2 Introduction 3 Specifications and Environmental Conditions 3.1 Specifications 3.2 Environmental Conditions 3.3 Warranty 4 Safety Guidelines 5 Quick Start 5.1 Unpacking 5.2 Set-Up 5.3 Power 5.4 Setting the Temperature 6 Parts and Controls 6.1 Back Panel 6.2 Front Panel 6.3 Constant Temperature Block Assembly 6.3.1 Constant Temperature Block 6.3.2 Probe Sleeves and Tongs Page 7 General Operation 7.1 Changing Display Units Un= C 7.2 Switching to 230V Operation 8 Controller Operation 8.1 Well Temperature 962.3 C 8.2 Temperature Set-point 8.2.1 Programmable Set-points Page S 8.3 Scan S 8.4 Ramp and Soak Program 8.4.1 Program Points 962.4 S+U S 8.4.3 Program Set-Points SP 1 SP 4 S 0962.7 0970.0 S Pt 4 S 00001 00200 S Sr 4 S 10.0 11.3 S 8.4.4 Program Function Mode Pf=1 Pf=4 S 8.4.5 Program Control P=OFF P=Go S 8.5 Secondary Menu 8.6 Heater Power 962.4 8.7 Set-point Voltage S 11.934U 8.8 Proportional Band S 11.934 U S ProP 30.0 30.5 S 8.9 Controller Configuration 8.10 Operating Parameters S 8.11 Serial Interface Parameters Page 8.12 Calibration Parameters Page 9 Digital Communication Interface 9.1 Serial Communications 9.1.1 Wiring 9.1.2 Setup 9.1.3 Serial Operation 9.2 Interface Commands Table 2 Communications Command Summary 9 Digital Communication Interface Interface Commands Table 3 Communications Commands Summary continued Table 4 Communications Commands Summary continued 10 Test Probe Calibration 10.1 Calibrating a Single Probe 10.2 Furnace Characteristics 10.2.1 Stabilization and Accuracy Page 11 Calibration Procedure 11.1 Calibration Points 11.2 Calibration Procedure Page 12 Maintenance 13 Troubleshooting 13.1 Troubleshooting Problems,Possible Causes, and Solutions 13.2 Comments 13.2.1 EMC Directive 13.2.2 Low Voltage Directive (Safety)