Fluke 9150 S, S, S

it can be adjusted.

00200 Program point 4 soak time set for 200 minutes

Press “SET” to savethe new soak-time value or “EXIT” to discard changes

SAccept the program point soak time

The nextvalue to edit is the program scan rate. This value is ignored if scan is

not enabled for the unit (See Section 8.3.1).

Sr 4 Program point 4 scan rate

Press “SET” to edit the program scan rate.

SEdit the program point scan rate

10.0 Current program point 4 scan rate

Use “UP” and “DOWN”to adjust the program scan rate.

11.3 New program point 4 scan rate

Press “SET” to savethe new scan rate value or “EXIT” to discard changes.

SAccept the program point scan rate

After “SET”is pressed the controller advances to the next program point or, if

thereare no more program pointsto edit, exits to the Program Function Menu.

Repeatthe above steps to edit any program point.

8.4.4 Program Function Mode

The nextparameter is the program function or cycle mode. There are four pos-

sible modes which determine whether the program scans up (from set-point 1

to n) only or both up and down(from set-point n to 1), and also whether the

program stops afterone cycle or repeats the cycle indefinitely. The table below

showsthe action of each of the four program mode settings.

Function Action

1 up-stop

2 up-down-stop

3 up-repeat

4 up-down-repeat

Pf=1

27

8 Controller Operation

Ramp and Soak Program

Contents

Main Page Table of Contents 9 Digital Communication Interface . . . . . . . . . . . . . . . . 37 10 Test Probe Calibration . . . . . . . . . . . . . . . . . . . . . . 43 Page 1 Before You Start 1.1 Symbols Used 1.2 Safety Information 1.2.1 WARNINGS 1.2.2 CAUTIONS 1.3 Authorized Service Centers Page 2 Introduction 3 Specifications and Environmental Conditions 3.1 Specifications 3.2 Environmental Conditions 3.3 Warranty 4 Safety Guidelines 5 Quick Start 5.1 Unpacking 5.2 Set-Up 5.3 Power 5.4 Setting the Temperature 6 Parts and Controls 6.1 Back Panel 6.2 Front Panel 6.3 Constant Temperature Block Assembly 6.3.1 Constant Temperature Block 6.3.2 Probe Sleeves and Tongs Page 7 General Operation 7.1 Changing Display Units Un= C 7.2 Switching to 230V Operation 8 Controller Operation 8.1 Well Temperature 962.3 C 8.2 Temperature Set-point 8.2.1 Programmable Set-points Page S 8.3 Scan S 8.4 Ramp and Soak Program 8.4.1 Program Points 962.4 S+U S 8.4.3 Program Set-Points SP 1 SP 4 S 0962.7 0970.0 S Pt 4 S 00001 00200 S Sr 4 S 10.0 11.3 S 8.4.4 Program Function Mode Pf=1 Pf=4 S 8.4.5 Program Control P=OFF P=Go S 8.5 Secondary Menu 8.6 Heater Power 962.4 8.7 Set-point Voltage S 11.934U 8.8 Proportional Band S 11.934 U S ProP 30.0 30.5 S 8.9 Controller Configuration 8.10 Operating Parameters S 8.11 Serial Interface Parameters Page 8.12 Calibration Parameters Page 9 Digital Communication Interface 9.1 Serial Communications 9.1.1 Wiring 9.1.2 Setup 9.1.3 Serial Operation 9.2 Interface Commands Table 2 Communications Command Summary 9 Digital Communication Interface Interface Commands Table 3 Communications Commands Summary continued Table 4 Communications Commands Summary continued 10 Test Probe Calibration 10.1 Calibrating a Single Probe 10.2 Furnace Characteristics 10.2.1 Stabilization and Accuracy Page 11 Calibration Procedure 11.1 Calibration Points 11.2 Calibration Procedure Page 12 Maintenance 13 Troubleshooting 13.1 Troubleshooting Problems,Possible Causes, and Solutions 13.2 Comments 13.2.1 EMC Directive 13.2.2 Low Voltage Directive (Safety)