Fluke 9150 1.3 Authorized Service Centers

Allowfor test probe expansion inside the well as the furnace heats.

DO NOTuse fluids to clean ou t the well.

Neverintroduce foreign material into the probe hole of the insert. Fluids, etc.

can leak into the calibrator causing damage.

DO NOTchange the values of the calibration constants from the factory set

values.The co rrectsettin g of these parameters is important to the safety and

proper operation of thecalibrator.

DO NOTdrop or force the probe stems into the well. This type of action can

cause a shock to the sensor and affectthe calibration.

DO use a ground faultinterrupt device.

1.3 Authorized Service Centers

Pleasecontact one of the following authorized Service Centers to coordinate

serviceon your Hart product:

Fluke Corporation, Hart Scientific Division

799 E. Utah Valley Drive

American Fork, UT 84003-9775

USA

Phone: +1.801.763.1600

Telefax: +1.801.763.1010

E-mail: support@hartscientific.com

FlukeNederland B.V.

Customer Support Services

Science Park Eindhoven 5108

5692 EC Son

NETHERLANDS

Phone: +31-402-675300

Telefax: +31-402-675321

E-mail:ServiceDesk @fluke.nl

FlukeInt'l Corporation

Service Center - Instrimpex

Room 2301 Sciteck Tower

22 Jianguomenwai Dajie

9150 Portable Furnace

User’s Guide

4

Contents

Main Page Table of Contents 9 Digital Communication Interface . . . . . . . . . . . . . . . . 37 10 Test Probe Calibration . . . . . . . . . . . . . . . . . . . . . . 43 Page 1 Before You Start 1.1 Symbols Used 1.2 Safety Information 1.2.1 WARNINGS 1.2.2 CAUTIONS 1.3 Authorized Service Centers Page 2 Introduction 3 Specifications and Environmental Conditions 3.1 Specifications 3.2 Environmental Conditions 3.3 Warranty 4 Safety Guidelines 5 Quick Start 5.1 Unpacking 5.2 Set-Up 5.3 Power 5.4 Setting the Temperature 6 Parts and Controls 6.1 Back Panel 6.2 Front Panel 6.3 Constant Temperature Block Assembly 6.3.1 Constant Temperature Block 6.3.2 Probe Sleeves and Tongs Page 7 General Operation 7.1 Changing Display Units Un= C 7.2 Switching to 230V Operation 8 Controller Operation 8.1 Well Temperature 962.3 C 8.2 Temperature Set-point 8.2.1 Programmable Set-points Page S 8.3 Scan S 8.4 Ramp and Soak Program 8.4.1 Program Points 962.4 S+U S 8.4.3 Program Set-Points SP 1 SP 4 S 0962.7 0970.0 S Pt 4 S 00001 00200 S Sr 4 S 10.0 11.3 S 8.4.4 Program Function Mode Pf=1 Pf=4 S 8.4.5 Program Control P=OFF P=Go S 8.5 Secondary Menu 8.6 Heater Power 962.4 8.7 Set-point Voltage S 11.934U 8.8 Proportional Band S 11.934 U S ProP 30.0 30.5 S 8.9 Controller Configuration 8.10 Operating Parameters S 8.11 Serial Interface Parameters Page 8.12 Calibration Parameters Page 9 Digital Communication Interface 9.1 Serial Communications 9.1.1 Wiring 9.1.2 Setup 9.1.3 Serial Operation 9.2 Interface Commands Table 2 Communications Command Summary 9 Digital Communication Interface Interface Commands Table 3 Communications Commands Summary continued Table 4 Communications Commands Summary continued 10 Test Probe Calibration 10.1 Calibrating a Single Probe 10.2 Furnace Characteristics 10.2.1 Stabilization and Accuracy Page 11 Calibration Procedure 11.1 Calibration Points 11.2 Calibration Procedure Page 12 Maintenance 13 Troubleshooting 13.1 Troubleshooting Problems,Possible Causes, and Solutions 13.2 Comments 13.2.1 EMC Directive 13.2.2 Low Voltage Directive (Safety)