Fluke 9150 7 General Operation

7 General Operation

7.1 Changing Display Units

The 9150 can displaytemperature in Celsius or Fahrenheit. The temperature

unitsare shipped from the factory set to Celsius. To change to Fahrenheit or

back to Celsius there are twoways:

1 - Press the “SET” and “DOWN”simultaneously.

or

1 - Press the “SET” keythree times from the temperature display and then

“EXIT” to showth e units.

Un= C

2 - Press the “UP” or “DOWN”key to change units.

3 - Press “SET”to store changes and then “EXIT” to display the temperature.

7.2 Switching to 230V Operation

The 9150 isswitchable from 115 VAC to 230 VAC50/60 Hz. Switching the

voltage can change the calibration, so the unit should be calibrated after

changing the input voltage.

Tochange from 115 VACto 230 VAC

1. Unplug the unit.

2. With a small straight slot screwdriver remove the fuse holder from the

PEMlocated on the back of the unit.

3. Replace the two 12A F 250V fuses with two 6.3A F 250V fuses.

4. Replace the fuse holder with the “230V” in the display window.

5. Lay the unit on its side and with a small straight slot screwdriver, move

the heater switches located on the bottom of the unit to display “230V”.

Note: If the heater switchesand the fuse holder d o not allread “230Vwhen

complete,the unit will either not heat or only heat at a fraction o f its capacity.

If not done properly,the unit could become damaged and void the calibration

and warranty.Refer to Section 3.1, Specifications, for correct fuse usage.

CAUTION:Do not plug the unit into 230V if the heater switches and fuse

holder read 115V. This will cause the fuses to blow and may damage the

instrument.

19

7 General Operation

Changing Display Units

Contents

Main Page Table of Contents 9 Digital Communication Interface . . . . . . . . . . . . . . . . 37 10 Test Probe Calibration . . . . . . . . . . . . . . . . . . . . . . 43 Page 1 Before You Start 1.1 Symbols Used 1.2 Safety Information 1.2.1 WARNINGS 1.2.2 CAUTIONS 1.3 Authorized Service Centers Page 2 Introduction 3 Specifications and Environmental Conditions 3.1 Specifications 3.2 Environmental Conditions 3.3 Warranty 4 Safety Guidelines 5 Quick Start 5.1 Unpacking 5.2 Set-Up 5.3 Power 5.4 Setting the Temperature 6 Parts and Controls 6.1 Back Panel 6.2 Front Panel 6.3 Constant Temperature Block Assembly 6.3.1 Constant Temperature Block 6.3.2 Probe Sleeves and Tongs Page 7 General Operation 7.1 Changing Display Units Un= C 7.2 Switching to 230V Operation 8 Controller Operation 8.1 Well Temperature 962.3 C 8.2 Temperature Set-point 8.2.1 Programmable Set-points Page S 8.3 Scan S 8.4 Ramp and Soak Program 8.4.1 Program Points 962.4 S+U S 8.4.3 Program Set-Points SP 1 SP 4 S 0962.7 0970.0 S Pt 4 S 00001 00200 S Sr 4 S 10.0 11.3 S 8.4.4 Program Function Mode Pf=1 Pf=4 S 8.4.5 Program Control P=OFF P=Go S 8.5 Secondary Menu 8.6 Heater Power 962.4 8.7 Set-point Voltage S 11.934U 8.8 Proportional Band S 11.934 U S ProP 30.0 30.5 S 8.9 Controller Configuration 8.10 Operating Parameters S 8.11 Serial Interface Parameters Page 8.12 Calibration Parameters Page 9 Digital Communication Interface 9.1 Serial Communications 9.1.1 Wiring 9.1.2 Setup 9.1.3 Serial Operation 9.2 Interface Commands Table 2 Communications Command Summary 9 Digital Communication Interface Interface Commands Table 3 Communications Commands Summary continued Table 4 Communications Commands Summary continued 10 Test Probe Calibration 10.1 Calibrating a Single Probe 10.2 Furnace Characteristics 10.2.1 Stabilization and Accuracy Page 11 Calibration Procedure 11.1 Calibration Points 11.2 Calibration Procedure Page 12 Maintenance 13 Troubleshooting 13.1 Troubleshooting Problems,Possible Causes, and Solutions 13.2 Comments 13.2.1 EMC Directive 13.2.2 Low Voltage Directive (Safety)