Manuals / Brands / Household Appliance / Furnace / Fluke / Household Appliance / Furnace

Fluke 9150 Table 4 Communications Commands Summary continued

1 49

Download 49 pages, 541.38 Kb

9150 Portable Furnace

User’s Guide

CommandDescription

Command

Format

Command

Example Returned

Returned

Example

Acceptable

Values

Thesecommands are only used for factory testing.

Miscellaneous(not on menus)

Readfirmware version number *ver[sion] *ver ver.9999,9.99 ver.9150,2.20

Readstructure of all commands h[elp] h listofcommands

Legend: []Optional Command data

{}Returns eitherinfo rmation

nNumeric data supplied by user

9Numeric data returned to user

xCharacter data returned to user

Note: WhenDUPLEX is set to FULL and a command is sent to READ, the command is returned followed by a

carriagereturn and linefeed. Then the value is returned as indicated in the RETURNED column.

Table 4 Communications Commands Summary continued

Contents

Main Page Table of Contents 9 Digital Communication Interface . . . . . . . . . . . . . . . . 37 10 Test Probe Calibration . . . . . . . . . . . . . . . . . . . . . . 43 Page 1 Before You Start 1.1 Symbols Used 1.2 Safety Information 1.2.1 WARNINGS 1.2.2 CAUTIONS 1.3 Authorized Service Centers Page 2 Introduction 3 Specifications and Environmental Conditions 3.1 Specifications 3.2 Environmental Conditions 3.3 Warranty 4 Safety Guidelines 5 Quick Start 5.1 Unpacking 5.2 Set-Up 5.3 Power 5.4 Setting the Temperature 6 Parts and Controls 6.1 Back Panel 6.2 Front Panel 6.3 Constant Temperature Block Assembly 6.3.1 Constant Temperature Block 6.3.2 Probe Sleeves and Tongs Page 7 General Operation 7.1 Changing Display Units Un= C 7.2 Switching to 230V Operation 8 Controller Operation 8.1 Well Temperature 962.3 C 8.2 Temperature Set-point 8.2.1 Programmable Set-points Page S 8.3 Scan S 8.4 Ramp and Soak Program 8.4.1 Program Points 962.4 S+U S 8.4.3 Program Set-Points SP 1 SP 4 S 0962.7 0970.0 S Pt 4 S 00001 00200 S Sr 4 S 10.0 11.3 S 8.4.4 Program Function Mode Pf=1 Pf=4 S 8.4.5 Program Control P=OFF P=Go S 8.5 Secondary Menu 8.6 Heater Power 962.4 8.7 Set-point Voltage S 11.934U 8.8 Proportional Band S 11.934 U S ProP 30.0 30.5 S 8.9 Controller Configuration 8.10 Operating Parameters S 8.11 Serial Interface Parameters Page 8.12 Calibration Parameters Page 9 Digital Communication Interface 9.1 Serial Communications 9.1.1 Wiring 9.1.2 Setup 9.1.3 Serial Operation 9.2 Interface Commands Table 2 Communications Command Summary 9 Digital Communication Interface Interface Commands Table 3 Communications Commands Summary continued Table 4 Communications Commands Summary continued 10 Test Probe Calibration 10.1 Calibrating a Single Probe 10.2 Furnace Characteristics 10.2.1 Stabilization and Accuracy Page 11 Calibration Procedure 11.1 Calibration Points 11.2 Calibration Procedure Page 12 Maintenance 13 Troubleshooting 13.1 Troubleshooting Problems,Possible Causes, and Solutions 13.2 Comments 13.2.1 EMC Directive 13.2.2 Low Voltage Directive (Safety)