Thermal Management Default Thermal Monitor | Foxconn 661M03 manual

Chapter 3 BIOS Description

CPU Feature Menu

Thermal Management (Default: Thermal Monitor 1)

This option is used to manage Prescott CPU thermal.

Note: This function will not be displayed until a Prescott CPU has been installed.

TM2 Bus Ratio (Default: 0 X)

Represents the frequency bus ratio of the throttled performance state that will be initiated when the on-diesensor gose from not hot to hot.

TM2 Bus VID (Default: 0.8375V)

Represents the voltage of the throttled performance state that will be initi- ated when the on-diesensor gose from not hot to hot.

42	661M03 Series User Manual

Image 50

Foxconn 661M03 user manual Thermal Management Default Thermal Monitor, TM2 Bus Ratio Default 0, TM2 Bus VID Default

Contents

Version Item Checklist Declaration of conformity HON HAI Precision Industry Table of Contents Chapter Directions for Bundled Software Chapter Special Bios FunctionsChapter Driver CD Introduction Page Page Page Main Features Onboard I/O Onboard 1394 optionalOnboard LAN Onboard Graphics Advanced Features Green Function Motherboard Layout PHY optional ATX 12V connectorATX power connector AGP slot Flash Rom Floppy disk connectorIDE connectors South Bridge controller Installation Instructions Installation Instructions Installation of CPU CPU Installation of CPU Fan Installation Instructions Frequence CPU Qualified Vendor ListVendor Type Installation of DDR Memory Memory Memory Qualified Vendor List Vender Type Size Chapter Installation Instructions Pin ATX12V Power Connector PWR2 Power SupplyPin ATX power connector PWR1 Rear Panel Connectors This motherboard provides the ports as below Line-in Line-out Front channels Microphone HDD connectors IDE1 & IDE2 Other ConnectorsFDD Connector Front Panel Connector FP1 IrDA Header IR optional USB Headers Fusb Fan Connectors CPUFAN, FAN1 Audio Connectors Cdin Header F1394 optional Wake-Up On LAN WOL Pdif Out Connector Spdout Audio Interface Faudio AGP Slot Expension SlotsPCI Slots Vender Type Video Memory Installing an expansion cardAGP Qualified Vendor List CNR Slot optional Clear Cmos Jumper Clscmos JumpersDescription of Jumpers BIOS-Protection Jumper Fwhen CNR Audio Selection Jumper J24 Powering off the computer Starting up for the first time Bios Description Standard Cmos Features Enter Bios SetupPress TAB to show Post screen, DEL to enter Setup Bios Features Power Management Setup Advanced Bios FeaturesAdvanced Chipset Features PnP/PCI Configurations Time Standard Cmos FeaturesDate IDE Primary/Secondary Master/Slave Halt On Drive A/BVideo Memory Bios Features SuperBoot SuperBoot Default Disabled Advanced Bios Features Boot Other Device Default Enabled Quick Power On Self Test Default EnabledFirst/Second/Third Boot Device Default Floppy/HDD- 0/CDROM Swap Floppy Drive Default Disabled Apic Mode Default Enabled Typematic Delay Msec DefaultSecurity Option Default Setup MPS Version Control For OS Default TM2 Bus VID Default Thermal Management Default Thermal MonitorTM2 Bus Ratio Default 0 Advanced Chipset Features Dram CAS Latency Default 2.5T Performance Mode Default DisabledDram Timing control Default By SPD RAS Active Time tRAS Default 6T AGP Fast Write Support Default Enabled AGP Aperture Size Default 64 MBGraphic Window WR Combin Default Disabled AGP Data Rate Default Auto VGA Share Memory Size Default 32 MB Graphics Engin Clock Default 133 MHz Integrated Peripherals IDE Primary/ Secondary Master/Slave PIO Default Auto Audio Access Interface Default EDB BusInternal PCI/IDE Default Both Primary/Secondary Master/Slave UltraDMA Default Auto USB 2.0 Supports Default Enabled SIS USB Controller Default EnabledUSB Ports Number Default 6 ports USB Keyboard Support Default Enabled Uart Mode Select Default Normal Onboard FDC Controller Default EnabledOnboard Serial Port1/2 Default 3F8/IRQ4 / 2F8/IRQ3 UR2 Duplex Mode Default Half Acpi Suspend Type Default S1POS Power Management SetupAcpi function Default Enabled Power Management Default User Define Switch Function Default Break/Wake Video Off Option Default Susp, Stby offVideo Off Method Default Dpms Supported Modem Use IRQ Default Auto Ring Power Up Control Default Enabled IRQ 3-7,9-15, NMI Default EnabledIRQ 8 Break Suspend Default Disabled Macpme Power Up Control Default Enabled Time hhmmss Alarm Month AlarmDay of Month Alarm Primary/Secondary IDE Default Disabled Resources Controlled By Default AutoESCD PnP/PCI ConfigurationsReset Configuration Data Default Disabled PCI/VGA Palette Snoop Default Disabled PC Health Status Frequency/Voltage Control Set Password Load Fail-Safe DefaultsLoad Optimized Defaults Enter Password Save to Cmos and Exit Y/N?Y Save & Exit SetupExit Without Saving Quit Without Saving Y/N?N Chapter Accessories Utility CD contentInstall Driver Browse CD Start to Install divers Install IDE Driver Install AGP Driver Install VGA Driver Install DirectX Installing the Audio Driver Install USB 2.0 DriverUsing 4-/6-Channel Audio Attaching Speakers Channel Analog Audio Output Line-out Rear channels Line-out Front channels Microphone Selecting 4- or 6-Channel Setting Digital Audio Output Click the Speaker Configuration tab Testing Each Speaker Playing Karaoke Install LAN Driver Install Norton Internet Security Directions for Bundled Software SuperStep features Using SuperStep Directions for Bundled Software Directions for Bundled Software SuperLogo features Using SuperLogo Directions for Bundled Software SuperUpdate features Using SuperUpdate Directions for Bundled Software Backup Bios to local image Directions for Bundled Software Directions for Bundled Software Update Bios On-line Click OK to update Bios Click Restart Special Bios Functions SuperSpeed SuperBoot SuperBIOS-Protect SuperRecovery Hotkey Selection Hard Disk Selection Divide Hidden Partition What is a Hidden Partition?Main Menu Divide Hidden Partition Release Hidden Partition Backup Partition Table BackupBackup Cmos Setup Backup Hard disk Data Recovery Back to Main Recover Cmos Setup Recover Partition Table Change Password Introduction Recover Hard disk Data