Installation on the underside of a desk | Furuno SC-50 specification

2. INSTALLATION

2.3.2Installation on the underside of a desk

The processor unit may be mounted on the underside of a desk as shown in the figure below. Do not install it on the overhead.

Desk

Name Plate

Installation of processor unit on the underside of a desk

2-13

Image 22

Furuno SC-50 manual Installation on the underside of a desk, Installation of processor unit on the underside of a desk

Contents

Satellite Compass Safety Instructions Table of Contents MAINTENANCE, Troubleshooting Iii Foreword FeaturesWord to the Owner of the SC-50 System Configuration System configuration Optional equipment Equipment ListStandard supply Name Type Code No Qty Remarks Principle of Operation This page intentionally left blank Mounting Considerations InstallationAntenna unit Horizontal separation between antenna and masts Mast diameter Separation distance minimumAntenna and field of view Example of antenna installed below superstructures Display unit, processor unit Mounting dimensions for antenna, orienting the antenna Installing the Antenna UnitsAntenna unit SC-303 Coating bolt, nut and washers with silicone sealant Waterproofing the antenna connectorHow to fasten the antenna cable Cable from antenna No. marked on cable How to insert the cable cover Antenna unit Mounting How to orient the antenna elementsAntenna unit SC-603 Antenna unit SC-603 Fixing antenna unit to pedestal Orient the antenna unit as shown in the illustration below Orienting the antenna unit Welding the antenna unit Fastening the antenna cable Antenna element Deck, bulkhead mount Installing the Processor UnitProcessor unit orientation, deck mounting Installation on the underside of a desk Installation of processor unit on the underside of a desk Flush mount Installing the Display UnitDesktop, overhead mounting Flush mount F Flush mount S kit Type OP20-17, Code No Flush mount SFlush mount S General wiring diagram WiringProcessor unit, rear view How to install the optional antenna cable set Sectional view of coaxial cable 3D2V How to attach connector N-P-8DFB How to attach connector N-P-8DFB Confirming satellite status choosing mounting method Initial SettingsInstallation setup menu Main menu Choosing heading source Heading setup menuSatellite tracking status display Connection of External Equipment General wiringProcessor unit, cover opened Fabrication of cables Cable Sectional view, fabrication Controls OperationDisplay unit Panel Illumination, Display Contrast Turning the Power On/OffProcessor unit Heading display Choosing a DisplayDescription of displays Nav data display Compass display Steering displayROT Rate-of-Turn display Set and Drift display, Distance Run display Set and drift display, speed and distance run display Dgps alarm options Dgps Alarm SetupAlarm menu Buzzer options Confirming Satellite Status Satellite status display Displaying the GPS setup menu GPS SetupGPS Setup menu description Output Data Disable SV Disable satelliteHeading Data OUT1 menu, sentences Baud rate options IEC, Nmea version options Tx interval optionsHeading talker options Log pulse Log pulse options System Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Demonstration mode WAAS/DGPS menu WAAS/DGPS SetupPosition fix mode options Waas Search options GEO satellite and coverage area Provider GEO Satellite LongitudeAUTO/MANUAL options Operation Others menu HDG Backup optionsOthers Menu HDG Restoration options Trip Menu Trip menu Resetting Distance Run Reset Distance prompt This page intentionally left blank MAINTENANCE, Troubleshooting Preventive Maintenance Troubleshooting TroubleshootingSymptom Cause Remedy Test menu options DiagnosticsDiagnostic test1 Test start prompt Diagnostic test sequence Push KEY Diagnostic test2 TEST2 display Diagnostic test3 Alarm options Program version no. display Program NumberClearing Data Prompts for erasure of data Prompt for exchanging battery Replacement of BatteryBattery Location Type Code No Prompt for turning off the power Error Message Meaning Remedy Replacement of FuseError Messages Message display Error messages con’t from previous Data ERR Menu Tree AppendixAP-1 AP-2 Specifications SC-50 Furuno Index IN-1 ＰａｃｋｉｎｇＬｉｓｔ SC-501-J/E SC-303 工事材料表 Installation Materials ﾌﾗｯｼｭﾏｳﾝﾄｷｯﾄ 20AY-X-9403 SC-50/55/60 20AT-X-9410 Page Page Page