Installing 6KPM Cards in the Magnum 6K25 | GarrettCom instruction

Magnum 6K25 Managed Fiber Switch

Installation and User Guide (04/06)

Caution: Be careful not to disturb the power supply.

Looking down into the Magnum 6K25 unit, notice that there are individual PM installation spaces and female latch(white) connectors provided on the main board along with four stand-off’s for each 6KPM card position. (See Figure 3.5.1b).

Figure 3.5.1b: Magnum 6k25, Top view without chassis cover

Step 3. Remove front panel face plate retaining screws

There are four PM slots (A, B, C and D) located on the front of the chassis cover. Looking into the vertical placed Chassis cover of the unit, there are three brackets with retaining screws (#256 flat head ) which hold each PM Face plate card slot securely. These six screws shown in the picture below are used to secure a PM face plate in position, but unscrew only four of the screws as shown in Fig. below. These screws are also used to secure the individual 6KPM cards screen plate which can be subjected to significant forces from the attached cables. (See Figure 3.5.1c)

Figure 3.5.1c: Top View – 6KPM retaining screws hold Face Plate

3.5.2Installing 6KPM Cards in the Magnum 6K25

Up to four front-mounted 6KPM cards may be installed in one Magnum 6K25 Managed Fiber Switch unit. Follow these steps to install a 6KPM.

Step 1. Remove top chassis cover. See procedure in Section 3.5.1 above.

www . GarrettCom . com

29

Image 36

GarrettCom manual Installing 6KPM Cards in the Magnum 6K25, 1c Top View 6KPM retaining screws hold Face Plate

Contents

Managed Fiber Switch Trademarks Contacting GarrettCom, Inc Canadian Emission Specifications Troubleshooting Revisions Magnum Line Technical Specifications PerformanceNetwork Standards and Compliance, hardware Maximum 10 Mbps Ethernet Segment Lengths Fiber Multi-mode connector types supported Fiber Single-mode connector typesManagement Console connector Power Supply Internal Alarm Contact Optional Nebs Testing and Certification Nebs certifiedPer-port MDI or Mdix on RJ-45 Agency Approvals Ordering Information For Gigabit module configuration options 6K PoE Modules with 48VDC Pass-Through 6K PoE Modules with 48VDC Power Inside Introduction Inspecting the Package and Product Product Description Magnum 6K25 Managed Fiber Switch 1a Regular 6K25 front view, configured for 24 +1 Gb ports Magnum 6K25 and 6K25R chassis Eight-port SFF fiber modules 6K8-MTRJ, 6K8-MLC, 100Mb fiber Eight-Port Copper Module, 6K8-RJ45 The 6K25-Series’s8-port New PoEPower Inside, model PI6KP8-45RJ MDIX, 10/100Mb 8-port ACT LK RX Four-Port 10 Mb mm Fiber ST Modules Gigabit 1000Mbps port modules Packet Prioritization, 802.1p QOS Frame Buffering and Flow Control@ 1000Mb Fiber SC + 4@10/ 100Mb Managed Network Software MNS-6K for Magnum 6K25-Series GarrettCom proprietary MIBs for Snmp „ Managed switching for high performance Ethernet LANs „ Features Fiber-Built-In „ Nebs and Etsi tested and certified „ RJ-45 ports are MDI/MDIX supported Example 1 Magnum 6K25 Switch for a Vlan application Applications Www . GarrettCom . com Installation Locating Magnum 6K25 Switches Connecting Ethernet Media Connecting Fiber Optic ST-type, twist-lockIeee Standard Media Type Max. Distance Port Module Fiber Copper Connecting Fiber Optic SC-type, Snap-In Connecting Single-Mode Fiber OpticMedia Ieee Standard Table-Top or Shelf Mounting Rack-mounting for 19 Retma racks, regular Magnum 6K25s 1 Mountings for Magnum 6K25 units rack-mounted in a frame Powering the Magnum Managed Fiber Switch Rack-mounting, Reverse version of the Magnum 6K25s2 Reverse Magnum 6K25 units, rack-mounted in a frame 6K25 Port Module 6KPM Installation Preparation for Installing and Removing 6KPMs Remove Chassis Cover Installing 6KPM Cards in the Magnum 6K25 1c Top View 6KPM retaining screws hold Face Plate Uplink 2f Securely latching up 6KPM Cards into a Magnum 6K25 2g Top View 6KPM Module installed inside a 6K25 Removing 6KPM Cards 3b Removing a 6KPM Card Connecting the Console Terminal to Magnum 6K25 Management Pin Signal DescriptionDB-9 Console port connector Console DB-9 Port Switching Functionality Filtering and Forwarding Status LEDs Up-link MDI-MDIX on RJ-45 port modules, for port 1 onlyAuto-CrossMDIX and Auto-negotiation, for RJ-45 ports Www . GarrettCom . com Flow-control, Ieee 802.3x standard 6KP4 ’cvr Introduction Magnum 6K25 Managed Fiber Switch Port Modules ZXSC70 6KPM Module Description 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module 1c 6KP4 @10Mb @100Mb Multi-mode FX-ST twistLock Module Mode SC-type connectors. It Provides an advantage Fiber functions in one Module of the 6K25 SwitchCopper ports and 2 Single Through combining copper Port@ 100Mbps Multi-Mode Fiber port Distances up the IEEE-standard100Mbps distance limits, i.e Magnum 6KP8-45MT Module is a combo module withCopper and fiber Small Form Factor Placing more ports on one module Connector Small 6KP8-MLC, 8 ports @100Mbps multi-mode LC Form Factor 9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port PoE LEDs Summary Fig. the top 8-RJ45 GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 14 6KM-BLNK When Calling for Assistance Before Calling for Assistance Return Material Authorization RMA Procedure No Problem FoundShipping and Packaging Information Appendix a Warranty Information Appendix B Internal DC Power Supply Options B3.0 Applications for DC Powered Switches B4.1 UL Requirements for DC-powered units B4.0 Appendix C Internal DC Dual-Source Power Option B5.0 Operation C4.0 Features and Benefits of the DUAL-SOURCE Design C5.1 UL Requirements Example Magnum 6K25R-48VDCExample Magnum 6K25R-24VDC or Magnum 6K25R-125VDC