Manuals / GE / Household Appliance / Water System

GE 000 gpd to 288, E4H-CE Series, E8-CE Series manual Manufactured in the USA

Models: 000 gpd to 288 E4H-CE Series, E8-CE Series 000 gpd

1 45

Download 45 pages 17.31 Kb

Page 45

Call (952) 933-2277 for additional information, (800) 766-2599 in the U.S., or visit w w w.osmonics.com

Manufactured in the USA

Corporate Headquarters	Euro/Africa Operations	Asia/Pacific Operations
5951 Clearwater Drive	230 rue Robert Schuman	1044/8 SOI 44/2
Minnetonka, MN	ZA des Uselles	Sukhumvit Road Prakanong
55343-8995	F-77350 Le MØe sur Seine	Bangkok 10110
USA	FRANCE	THAILAND
(952) 933-2277 Phone	+33 1 64 10 2000 Phone	+66	2 38 14213 Phone
(952) 933-0141 Fax	+33 1 64 10 3747 Fax	+66	2 39 18183 Fax

' Copyright 2002, Osmonics, Inc.

Printed in USA, P/N 1233379 Rev.A

Image 45

GE 000 gpd to 288, E4H-CE Series, E8-CE Series manual Manufactured in the USA

Contents

Operation and Maintenance Manual E4H-CE AND E8-CE SERIES WATER PURIFICATION MACHINES3 m3/hr to 45 m3/hr 18,000 gpd to 288,000 gpd Page OPERATION AND MAINTENANCE MANUAL TABLE OF CONTENTSINSTRUCTIONS FOR E4H-CE AND E8-CE WATER PURIFICATION Cleaning MACHINE OPERATION AND MAINTENANCEMembrane Element Replacement FIELD INSTALLED ACCESSORIESLIST OF TABLES LIST OF FIGURESNormal Versus Cross Flow Filtration Membrane Element with Interconnectors Cavg Principles of OperationRejection RecoveryCavg - CP x Cavg400 5 66 · · · · · · · · · · · · · 1.4 Specifications for E-CE Series Machines Flow Specifications for Reverse Osmosis E-CE Machines2000 ppm NaCl Minimum/Maximum Min/Max Boost Pressure Membrane Element Specifications Feed Water Requirements MACHINE ConnectionsE4H-CE E8-CEFree chlorine 3.0 PREPARATION AND START-UP 3.1 Pretreatment for Water PurificationIodine compounds Quaternary germicides Cationic surfactants 3.2 Initial Start-Up3. Check for leaks at all connection points STEPSWARNING ALWAYS TURN POWER OFF TO CHANGE ANY WIRING The system is now operational 3.3 Daily Start-Up 3. Clean the machine with approved Osmonics cleaners 4.0 MACHINE OPERATION AND MAINTENANCE4.3 Cleaning 1. Change the pre-filter cartridges 2. Flush the machineTo clean membrane elements STEPS 4.5 Membrane Element Replacement 2. Drain all water from the pre-filter cartridge housing4.4 Draining Machine for Shipment STEPS 1. Disconnect the inlet, concentrate, and permeate outlets14. Return to Initial Start-Up Section NOTE Follow Membrane Element Specifications Table 4.6 Membrane Element RemovalSTEPS Page STEPS 5.3 Chemical Pump 5.4 Clean-In-Place InstallationSYMPTOM TROUBLESHOOTINGPOSSIBLE CAUSES REMEDIESSYMPTOM TROUBLESHOOTINGPOSSIBLE CAUSES REMEDIESSYMPTOM TROUBLESHOOTINGplumbing to the valve POSSIBLE CAUSESREMEDIES POSSIBLE CAUSESHigh operating pressure Water flowing whencontinued SYMPTOMMachine not operating POSSIBLE CAUSESdown Electrical machine shutSYMPTOM POSSIBLE CAUSESchanges after calibration Conductivity drifts orDisplay is blank pH reading is off by morefeed chemical Chemical pump will notChemical pump feed reverse of what you expect7.0 FORMS 7.1 RETURN GOODS AUTHORIZATION RGA E - S E R I E S S T A R T - U P D A T A S H E E T Switch SettingCustomer DateE-SERIES DAILY LOG SHEET 8.0 WARRANTY 8.1 Warranty Terms 8.4 Voidability of Warranty Minnetonka Operations Attn Customer Service Center GE OSMONICS, INC5951 Clearwater Drive Minnetonka, MN 55343 USA Page Manufactured in the USA