Manuals / GE / Household Appliance / Water System

GE 000 gpd to 288, E4H-CE Series, E8-CE Series manual Membrane Element with Interconnectors

Models: 000 gpd to 288 E4H-CE Series, E8-CE Series 000 gpd

1 45

Download 45 pages 17.31 Kb

Page 7

Membrane Element with Interconnectors

1.1.5Membrane Elements

Membrane elements are interleaved layers of semi-permeable membrane, spacer, and permeate carrier spiraled around a central permeate tube make up the mem- brane element.

Figure 1.2

Membrane Element with Interconnectors

1.1.6Clean-In-Place

The abbreviation for Clean-In-Place is CIP.

1.1.7Flow Control Center

The Flow Control Center features a concentrate flow control valve, a recycle flow control valve, and a pressure gauge. It is located directly behind the control enclo- sure.

1.1.8Average Pressure

PAVG (Average Pressure) = [(PPRIMARY + PFINAL) ⎟ 2]

1.1.9Concentration

Concentration equals the Total Dissolved Solids (TDS) concentration of a solution expressed as conductivity (∝S/cm) or parts per million (ppm).

2

Image 7

GE 000 gpd to 288, E4H-CE Series, E8-CE Series manual Membrane Element with Interconnectors

Contents

E4H-CE AND E8-CE SERIES WATER PURIFICATION MACHINES Operation and Maintenance Manual3 m3/hr to 45 m3/hr 18,000 gpd to 288,000 gpd Page TABLE OF CONTENTS OPERATION AND MAINTENANCE MANUALINSTRUCTIONS FOR E4H-CE AND E8-CE WATER PURIFICATION FIELD INSTALLED ACCESSORIES MACHINE OPERATION AND MAINTENANCECleaning Membrane Element ReplacementLIST OF TABLES LIST OF FIGURESNormal Versus Cross Flow Filtration Membrane Element with Interconnectors Cavg Principles of OperationCavg RecoveryRejection Cavg - CP x400 5 66 · · · · · · · · · · · · · Flow Specifications for Reverse Osmosis E-CE Machines 1.4 Specifications for E-CE Series Machines2000 ppm NaCl Minimum/Maximum Min/Max Boost Pressure Membrane Element Specifications Feed Water Requirements E8-CE ConnectionsMACHINE E4H-CE3.2 Initial Start-Up 3.0 PREPARATION AND START-UP 3.1 Pretreatment for Water PurificationFree chlorine Iodine compounds Quaternary germicides Cationic surfactants3. Check for leaks at all connection points STEPSWARNING ALWAYS TURN POWER OFF TO CHANGE ANY WIRING The system is now operational 3.3 Daily Start-Up 1. Change the pre-filter cartridges 2. Flush the machine 4.0 MACHINE OPERATION AND MAINTENANCE3. Clean the machine with approved Osmonics cleaners 4.3 CleaningTo clean membrane elements STEPS STEPS 1. Disconnect the inlet, concentrate, and permeate outlets 2. Drain all water from the pre-filter cartridge housing4.5 Membrane Element Replacement 4.4 Draining Machine for Shipment14. Return to Initial Start-Up Section 4.6 Membrane Element Removal NOTE Follow Membrane Element Specifications TableSTEPS Page STEPS 5.3 Chemical Pump 5.4 Clean-In-Place InstallationREMEDIES TROUBLESHOOTINGSYMPTOM POSSIBLE CAUSESREMEDIES TROUBLESHOOTINGSYMPTOM POSSIBLE CAUSESPOSSIBLE CAUSES TROUBLESHOOTINGSYMPTOM plumbing to the valveWater flowing when POSSIBLE CAUSESREMEDIES High operating pressurePOSSIBLE CAUSES SYMPTOMcontinued Machine not operatingPOSSIBLE CAUSES Electrical machine shutdown SYMPTOMpH reading is off by more Conductivity drifts orchanges after calibration Display is blankreverse of what you expect Chemical pump will notfeed chemical Chemical pump feed7.0 FORMS 7.1 RETURN GOODS AUTHORIZATION RGA Date Switch SettingE - S E R I E S S T A R T - U P D A T A S H E E T CustomerE-SERIES DAILY LOG SHEET 8.0 WARRANTY 8.1 Warranty Terms 8.4 Voidability of Warranty GE OSMONICS, INC Minnetonka Operations Attn Customer Service Center5951 Clearwater Drive Minnetonka, MN 55343 USA Page Manufactured in the USA