Manuals / GE / Household Appliance / Water System

GE 000 gpd to 288, E4H-CE Series, E8-CE Series manual Daily Start-Up

Models: 000 gpd to 288 E4H-CE Series, E8-CE Series 000 gpd

1 45

Download 45 pages 17.31 Kb

Page 21

3.3Daily Start-Up

Check the machine to insure isolation valves are in the proper positions for operation.

To turn the RO ON, press the RO button so it is in the ON position. If the alarm light is lit, push the “Alarm Reset” switch on the control enclosure and the alarm button on the OIT. If the alarm light stays lit, check the RO for an alarm condition. Otherwise, the main inlet valve will open, and the high-pressure pump will turn on. The high-pressure pump will not start if there is insufficient inlet pressure [< 0.8 bar (< 12 psi)].

16

Image 21

GE 000 gpd to 288, E4H-CE Series, E8-CE Series manual Daily Start-Up

Contents

Operation and Maintenance Manual E4H-CE AND E8-CE SERIES WATER PURIFICATION MACHINES3 m3/hr to 45 m3/hr 18,000 gpd to 288,000 gpd Page OPERATION AND MAINTENANCE MANUAL TABLE OF CONTENTSINSTRUCTIONS FOR E4H-CE AND E8-CE WATER PURIFICATION Cleaning MACHINE OPERATION AND MAINTENANCEMembrane Element Replacement FIELD INSTALLED ACCESSORIESLIST OF TABLES LIST OF FIGURESNormal Versus Cross Flow Filtration Membrane Element with Interconnectors Cavg Principles of OperationRejection RecoveryCavg - CP x Cavg400 5 66 · · · · · · · · · · · · · 1.4 Specifications for E-CE Series Machines Flow Specifications for Reverse Osmosis E-CE Machines2000 ppm NaCl Minimum/Maximum Min/Max Boost Pressure Membrane Element Specifications Feed Water Requirements MACHINE ConnectionsE4H-CE E8-CEFree chlorine 3.0 PREPARATION AND START-UP 3.1 Pretreatment for Water PurificationIodine compounds Quaternary germicides Cationic surfactants 3.2 Initial Start-Up3. Check for leaks at all connection points STEPSWARNING ALWAYS TURN POWER OFF TO CHANGE ANY WIRING The system is now operational 3.3 Daily Start-Up 3. Clean the machine with approved Osmonics cleaners 4.0 MACHINE OPERATION AND MAINTENANCE4.3 Cleaning 1. Change the pre-filter cartridges 2. Flush the machineTo clean membrane elements STEPS 4.5 Membrane Element Replacement 2. Drain all water from the pre-filter cartridge housing4.4 Draining Machine for Shipment STEPS 1. Disconnect the inlet, concentrate, and permeate outlets14. Return to Initial Start-Up Section NOTE Follow Membrane Element Specifications Table 4.6 Membrane Element RemovalSTEPS Page STEPS 5.3 Chemical Pump 5.4 Clean-In-Place InstallationSYMPTOM TROUBLESHOOTINGPOSSIBLE CAUSES REMEDIESSYMPTOM TROUBLESHOOTINGPOSSIBLE CAUSES REMEDIESSYMPTOM TROUBLESHOOTINGplumbing to the valve POSSIBLE CAUSESREMEDIES POSSIBLE CAUSESHigh operating pressure Water flowing whencontinued SYMPTOMMachine not operating POSSIBLE CAUSESdown Electrical machine shutSYMPTOM POSSIBLE CAUSESchanges after calibration Conductivity drifts orDisplay is blank pH reading is off by morefeed chemical Chemical pump will notChemical pump feed reverse of what you expect7.0 FORMS 7.1 RETURN GOODS AUTHORIZATION RGA E - S E R I E S S T A R T - U P D A T A S H E E T Switch SettingCustomer DateE-SERIES DAILY LOG SHEET 8.0 WARRANTY 8.1 Warranty Terms 8.4 Voidability of Warranty Minnetonka Operations Attn Customer Service Center GE OSMONICS, INC5951 Clearwater Drive Minnetonka, MN 55343 USA Page Manufactured in the USA