Instructions Safety Instructions

Care and cleaning of the range.

Be sure electrical power is off and all surfaces are cool before cleaning any part of the range.

Proper care and cleaning are important so your range will give you efficient and satisfactory service. Follow these directions carefully in caring for your range to assure safe and proper maintenance.

If your range is removed for cleaning, servicing or any reason, be sure the anti-tip device is re-engaged properly when the range is replaced. Failure to take this precaution could result in tipping of the range and cause injury.

How to Remove the Range for Cleaning and Servicing

Care and Cleaning Operating

Follow these steps to remove the range for servicing or cleaning hard to reach surfaces.

Shut off the gas supply to the range.

Disconnect the electrical supply to the range.

Disconnect the gas supply tubing to the range.

Slide the range forward to free the range foot from the Anti-Tip bracket. See the Installation Instructions for the location of the bracket.

Reverse these steps to re-install the range. If the gas line has been disconnected, check for gas leaks after re-connection. See the Installation Instructions for the gas lead test method.

NOTE: A trained technician should make the gas installation, disconnection and re-connection of the gas supply to the appliance.

Tips Installation Instructions

Lift-Up/Off Cooktop

Clean the area under the cooktop often. Built-up soil, especially grease, may catch on fire.

To make cleaning easier, the cooktop may be lifted up or off.

Be sure all burners are turned off before raising the cooktop. Then remove the grates.

Grasp the two front burner wells and lift the cooktop up or off. Be careful of the pilots when the cooktop is up.

After cleaning underneath the cooktop with hot, soapy water and a clean cloth, lower or replace the cooktop. Be careful not to pinch your fingers.

Customer Service Troubleshooting

Burner Grates

Grates should be washed regularly and after spillovers. Wash them in hot, soapy water and rinse with clean water.

After cleaning, dry thoroughly by putting them in a warm oven for a few minutes. Don’t put the grates back on the range while they are wet. When replacing the grates, be sure they’re positioned securely over the burners.

 

To get rid of burned-on food, place the

 

grates in a covered container (or plastic

 

bag) with 1/4 cup ammonia to loosen

 

the soil. Then scrub with a soap-filled

18

scouring pad if necessary.

 

Although they’re durable, the grates will gradually lose their shine, regardless of the best care you can give them. This is due to their continual exposure to high temperatures.

Do not operate a burner for an extended period of time without cookware on the grate. The finish on the grate may chip without cookware to absorb the heat.

Page 17 Page 19
Page 18
Image 18
GE 164D3333P185-1 Care and cleaning of the range, How to Remove the Range for Cleaning and Servicing, Lift-Up/Off Cooktop
Page 17 Page 19

164D3333P185-1 specifications

The GE 164D3333P185-1 is a high-performance component designed for industrial applications, particularly in the field of electrical engineering. This product demonstrates a blend of advanced technology, reliability, and efficiency, which makes it a preferred choice for various sectors.

One of the standout features of the GE 164D3333P185-1 is its robust design. Constructed with durable materials, it is built to withstand challenging environmental conditions. This durability ensures that it maintains performance integrity over time, minimizing the need for maintenance and reducing downtime in industrial operations.

The component incorporates state-of-the-art technologies that enhance its functionality. It utilizes advanced sensor technology, which allows for precise monitoring and control of electrical systems. This capability is crucial in applications where accuracy and reliability are paramount. Additionally, the GE 164D3333P185-1 is equipped with innovative power management features that improve energy efficiency, leading to cost savings in operational expenses.

Another key characteristic of the GE 164D3333P185-1 is its versatility. It can be seamlessly integrated into various systems, whether in manufacturing, energy production, or commercial applications. This adaptability makes it a valuable asset in the ever-evolving industrial landscape.

The GE 164D3333P185-1 also promotes enhanced safety features. It includes built-in protection mechanisms that guard against electrical surges and faults, ensuring a safe operational environment. This attribute is particularly important for organizations that prioritize safety and risk management as part of their operational protocols.

Moreover, the ease of installation and user-friendly interface of the GE 164D3333P185-1 simplify the integration process. Technicians can efficiently set up and operate the component without extensive training, leading to quicker project turnaround times.

In summary, the GE 164D3333P185-1 is an exemplary product that showcases the best of modern engineering. With its robust design, advanced technologies, energy efficiency, safety features, and versatility, it stands as a critical component for industries looking to enhance their operational capabilities. Adopting the GE 164D3333P185-1 means investing in a future-proof solution that addresses the demands of today's dynamic industrial environments.
Top Page Image Contents