GE C2S980 manual Care and cleaningof the range, Burner Caps and Heads, Installation, Instructions

Care and cleaningof the range.

Burner Caps and Heads

Before removingthe burner capsand heads remember their sizeand location.Replace them in the same location after cleaning.

NOTE: Do not use steelwoolor scouringpowders to clean the burnerparts.

Burner caps

Replacement

Burner Heads

Replaceburnerheadsoverthe electrodeson the cooktop, in the correctlocationsaccordingto theirsize.Thereis one small,one medium,one extra largeand one dual flameextra large burner head.

Burnercap is	Burnercap is NOT
properlyseated.	properlyseated.

Front right burner

Burnercap

Lift off whencool.Washburnercapsin hot, soapy waterand rinse with clean water.You may scour with a plastic scouring pad to removeburned-on food particles.

Burner Heads and Oval(Center) Burner Head/Cap Assembly

The burnerheadsand the ovalburnerhead/cap

Medium head

Extra large

head

Small head

Front of range	Dual flame extra
	large head

Operating Instructions Safety Instructions

Installation Instructions

Consumer Support Troubleshooting Tips

Burner head

Electrode

Burner base

Make sure the hole in the burnerhead is positionedover the electrodeand that the burnerhead is fully insertedinside the burnerbase. A small gap between the base and head is normal.

Front left burner,back right burner

and back left burner

Burnercap

Burnerhead

Stability	Use a sewing
chamber	needle or twist-
	tie to unclog
	the small hole
	in the burner
	head.

Burnerbase Electrode

Make sure the slot in the burnerhead is positionedover the electrode.

Hole in burner head

The oval burner head/cap assembly

is removable. Simply lift it off the range for cleaning. Use a sewing needle

or twist-tie to unclog the small hole in the burner heads.

assemblyare removable. Simply lift them off the range for cleaning.

For proper ignition, make sure the smallhole in the section that fits over the electrodeis kept open.A sewing needleor wire twist-tie works well to unclog it.

The slitsin the burnerheadsmustbe keptclean at all timesfor an even,unhamperedflame.

Cloggedor dirty burnerportsor electrodeswill not allow the burnerto operateproperly.

Any spill on or around an electrode must be carefuly cleaned. Take care to not hit an electrode with anythinghard or it could be damaged.

Clean the burnerheadsroutinely,especialy after bad spillovers, which could clog the openings. Lift off when cool.

To remove burned-on food, soakthe burnerheads in a solution of mild liquiddetergentand hot water for 20–30 minutes. For more stubbornstains,use a toothbrush.

After cleaning

Before putting the burnercaps,headsand oval head/capassembly back,shakeout excesswater and then dry them thoroughlyby settingin a warm ovenfor 30 minutes.

Makesurethe slot(on fromt left, backrightand back leftheads) and the hole(frontrighthead)in the burnerheadis positionedoverthe electrode.

Burner head	Hole
	Burnerhead
Electrode	Electrode
	Slot

Front right head

Oval (Center) Burner Head/Cap Assembly

Replacethe oval(center) head/capassemblyover the electrode on the cooktop.

Oval head and cap	Make sure the slot in the
assembly
	burner head is positioned
	over the electrode.

Slot

Front of range Electrode

Caps

Replacethe matchingsize capsontothe burner basesor heads.

Medium cap Small cap

Extra large cap	Dual flame extra
Front of range	large cap

Makesurethat the headsand caps are replaced in the correct locations.

32