Manuals / GE / Kitchen Appliance / Dishwasher

GE DH2000 operation manual Part, Description, Wash Pump/Motor Assembly

Models: DH2000

1 44

Page 27

		Wash Pump/Motor Assembly
Item	Part	Description	Qty.
No.	No.
1	114134	SLINGER, WATER	1
2	114135	NUT	9
3	114136	SCREW	9
4	114137	BACKPLATE, PUMP	1
5	114138	GASKET, PUMP	1
6	114139	SEAL, PUMP	1
7	114140	WASHER	1
8	114141	IMPELLER	1
9	114142	WASHER	1
10	114143	WASHER, LOCK	1
11	114144	NUT, IMPELLER	1
12	114145	HOUSING, PUMP	1
13	114322	CAPACITOR 15μF	1
14	114525	PUMP/MOTOR ASSEMBLY COMPLETE	1
		220VAC/60/1

NOTE:

THE MOTOR CANNOT BE ORDERED AS A SEPARATE REPLACEMENT PART.

Page 27

Image 27

GE DH2000 operation manual Part, Description, Wash Pump/Motor Assembly

Contents

2000 Series Door-type High Temperature DishwasherManual P/N 114614 rev. J Model 2000 SeriesIn Canada National Service DepartmentModel Number Serial Number VoltageHertz Phase Service Agent Tel Parts Distributor TelIn the U.S.A In CanadaREGISTER YOUR PRODUCT ONLINE Serial # FAILURE TO REGISTER YOUR PRODUCT MAY VOID YOUR WARRANTYPRODUCT REGISTRATION CARD ModelRevision History Revision HistoryLimited Warranty LIMITED WARRANTYTable of Contents Table of Contents2000 Series Door-type Dishwasher Optional Equipment consult factory Model DescriptionModel Description 2000 Series1. Inspect the outside of the dishwasher carton for signs of damage Installation ReceivingConverting Straight-through Operation to Corner Operation Installationwall Converting Straight-through Operation to Corner OperationInstallation Electrical Connections Three Phase OperationRefer to the next page for 3-phase to 1-phase field conversion instructionsRewire Booster Heater Element for 1PH Field Conversion from 3-phase to 1-phase OperationInstall Main Terminal Block Jumper Wire Rewire Wash Tank Heater Element for 1PHHot Water Connection Drain ConnectionInstallation Installation Vent Fan ControlChemical Dispenser Provisions 4. DO NOT REMOVE THE JUMPER BETWEEN THE COMMON TERMINALSInstallation Check List Initial Start-upis set between 20-25 PSI Operation Normal Operation Mode20-25 PSI Wash TemperatureFinal Rinse Temperature Normal Operation Mode continuedSANITIZED THE WARES AND THE GREEN CYCLE LIGHT GOES OUT Rinse Sentry Operation ModeAutomatic Drain Cycle DO NOT REMOVE WARES UNTIL THE FINAL RINSE CYCLE HASCleaning Cleaning and MaintenanceAfter Each Meal Period or every 8 Hours of Operation Wash Spray arm Paper ClipPlug Rinse Arm SpindleDe-liming DangerCleaning and Maintenance Cleaning and Maintenance MaintenanceDaily Maintenance Weekly MaintenanceCause SolutionTroubleshooting ConditionPage Service Replacement PartsService Replacement Parts IllustrationsWash Pump/Motor Assembly Part DescriptionWash Pump/Motor Assembly Booster Assembly JUMPER, STRIP spares used for conversion Booster AssemblyPart DescriptionControl Panel Assembly Control Panel Assembly PartDescription 2815 3324Wash and Rinse Spray Arm Assemblies Part DescriptionWash and Rinse Spray Arm Assemblies Hood and Door Assembly Hood and Door Assembly PartDescription Track Assemby Track Assembly PartDescription Wash Tank Heat, Drain, Screens, Hoses JUMPER, STRIP spare for conversrion Wash Tank Heat, Drain, Screens, HosesPart DescriptionDish Racks, Line Strainer, PRV PartDescription Part DescriptionDish Racks, Line Strainer, PRV Electrical Schematic, Timer Chart Timer Chart, Electrical SchematicTimer Chart Electrical SchematicRINSE Timer ChartTIME CYCLE - DH/MD2000 WASHAT! TENTION - VERY IMPORTANT 1 & 3 PHASEElectrical 702119