ge.com
Consumer SupportOperating InstructionsSafety Instructions Installation
Instructions Troubleshooting Tips
Lift-Off Oven Door
The oven door is removable, but it is heavy.
You may need help removing and replacing
the door.
To remove the door, open it a few inches
to the special stop position that will hold the
door open. Grasp firmly on each side and lift
the door straight up and off the hinges.
NOTE: Be careful not to place hands between
the hinge and the oven door frame as the
hinge could snap back and pinch fingers.
To replace the door, make sure the hinges
are in the special stop position. Position the
slots in the bottom of the door squarely over
the hinges. Then lower the door slowly and
evenly over both hinges at the same time. If
the hinges snap back against the oven frame,
pull them back out.
To clean the inside of the door:
■Do not allow excess water to run into
any holes or slots in the door.
■Because the area inside the gasket is
cleaned during the self clean cycle, you do
not need to clean this by hand. Any soap
left on the liner causes additional stains
when the oven is heated.
■The area outside the gasket can be
cleaned with a soap-filled plastic
scouring pad.
To clean the outside of the door:
■Use soap and water to thoroughly clean
the top, sides and front of the oven door.
Rinse well. You may also use a glass
cleaner to clean the glass on the outside
of the door.
■Spillage of marinades, fruit juices, tomato
sauces and basting materials containing
acids may cause discoloration and should
be wiped up immediately. When the
surface is cool, clean and rinse.
■Do not use oven cleaners, cleansing
powders or harsh abrasives on the
outside of the door.
Lift the door straight up and off the
hinges.
The gasket is designed with a gap
at the bottom to allow for proper
air circulation.
Do not rub or clean the door
gasket—it has an extremely low
resistance to abrasion.
If you notice the gasket becoming
worn, frayed or damaged in any
way or if it has become displaced
on the door, you should have it
replaced.
39
Stainless Steel Surfaces
(on some models)
Do not use a steel wool pad; it will scratch
the surface.
IMPORTANT: APPLY A PROTECTIVE COAT
OF CERAMA BRYTE®STAINLESSSTEEL
BRIGHTENERBEFORE USING. This will help
you to maintain the brightness and
appearance of your stainless steel range.
■In order to avoid any discolorations and/or
grease stains, we recommend cleaning
and removing any spills, spots and grease
from the range after use.
■It is important to use a soft cloth or paper
towel every time the range is cleaned to
avoid any scratches.
Read carefully the instructions on the back
of the Brightener for better results.
Cleaning Instructions:
1. Remove grates.
2. Wash using warm, soapy water:
Wet soft cloth or paper towel (avoid using
excessive water).
Wipe the surface in the direction of the
grain (following the steel lines).
Rinse and wring out a soft cloth or paper
towel and dry the range.
3. Apply a degreaser that does not contain
sodium hydroxide or Stainless Steel
Cleaner (follow instructions).
4. Apply Cerama Bryte®Stainless Steel
Brightener (follow instructions).
5. Repeat steps 2–4 as many times
as needed.
6. Put grates back in place.
Follow these instructions for any Stainless
Steel surface on your range.
DONOT USE for Cooktop or Stainless Steel
parts cleaning:
• Caustic Lye (Sodium Hydroxide) or cleaners
containing this chemical
• Hard or Steel Wool Pads
• Abrasive Materials or Chemicals
To inquire about purchasing stainless steel
appliance cleaner or polish, or to find the
location of a dealer nearest you, please call
our toll-free number:
National Parts Center 800.626.2002 (U.S.)
888.261.3055 (Canada)
ge.com (U.S.)
www.GEAppliances.ca (Canada)