GEAppliances.com

Problem

 

Possible Causes

What To Do

 

 

 

 

 

 

“F—” and a number

 

You have a function error code. • Touch the CLEAR/OFF pad. Put the oven back into

 

or letter flash

 

 

 

operation.

 

in the display

 

 

 

 

 

 

If the function code repeats.

• Disconnect all power to the range for at least 30

 

 

 

 

 

 

 

 

seconds and then reconnect power. If the function

 

 

 

 

 

error code repeats, call for service.

 

 

 

 

 

 

Control signals after

 

You forgot to enter a

• Touch the BAKE pad and desired temperature or

 

entering cooking time

 

bake temperature or

the SELF CLEAN pad and desired clean time.

 

or start time

 

cleaning time.

 

 

 

 

 

 

 

Display goes blank

 

A fuse in your home may

• Replace the fuse or reset the circuit breaker.

 

 

 

be blown or the circuit

 

 

 

 

breaker tripped.

 

 

 

 

 

 

 

 

 

The clock is in the

• See the Special features of your oven control section.

 

 

 

black-out mode.

 

 

 

 

 

 

 

Display flashes

 

Power failure.

• Reset the clock.

 

 

 

 

 

 

Unable to get the

 

Oven control pads were

• The BROIL and BAKE pads must be touched at

 

display to show “SF”

 

not touched properly.

the same time and held for 3 seconds.

 

 

 

 

 

 

“Probe” appears in

 

This is reminding you to

• Enter a probe temperature.

 

the display

 

enter a probe temperature

 

 

 

 

after plugging in the probe.

 

 

 

 

 

 

Power outage,

 

Power outage or surge.

• Reset the clock. If the oven was in use, you must reset

clock flashes

 

 

 

it by touching the CLEAR/OFF pad, setting the clock

 

 

 

 

 

and resetting any cooking function.

 

 

 

 

 

 

Steam from the vent

 

When using the convection

• This is normal.

 

 

 

feature, it is normal to see

 

 

 

 

steam coming out of the oven

 

 

 

 

vent. As the number of racks

 

 

 

 

or amount of food being

 

 

 

 

cooked increases, the amount

 

 

 

 

of visible steam will increase.

 

 

 

 

 

 

 

“Burning” or “oily”

 

This is normal in a new oven

• To speed the process, set a self-clean cycle for a

 

odor emitting from

 

and will disappear in time.

minimum of 3 hours. See the Using the self-cleaning

the vent

 

 

 

oven section.

 

 

 

 

 

 

Strong odor

 

An odor from the insulation

• This is temporary.

 

 

 

around the inside of the oven

 

 

 

 

is normal for the first few times

 

 

 

the oven is used.

 

 

 

 

 

 

 

Fan noise

 

A cooling fan or a convection

• This is normal. The cooling fan will turn off and

 

 

 

fan (depending on the

on to cool internal parts. It may run after the oven is

 

 

function you are using) may

turned OFF. The convection fan will cycle on and off

 

 

automatically turn on and off.

until the function is over or the door is opened.

 

 

 

 

 

LOC shows in the

 

The Range Lock-Out feature

• Be sure the surface burner controls are turned OFF.

display

 

is activated.

Turn this feature off to use the range. See the

41

 

 

 

 

Range Lock-Out section.

 

 

 

 

 

 

 

 

 

 

 

Support Consumer Tips Troubleshooting Cleaning and Care Instructions Operating Instructions Safety