Installation Preparation
USING DUCT COVER ACCESSORIES
A duct cover accessory is required for all ceiling heights. Use this chart to determine the correct Duct Cover Accessory for
Actual | *Possible Hood | Recirculating |
Ceiling | ||
Height | Installation Height | Accessory |
|
|
|
7′ 11″ |
|
|
|
|
| Y |
|
|
|
| ACCESSOR ZXR858C |
| 8′ 0″ |
| ||
|
|
|
| |
|
|
|
|
|
| 8′ 1″ |
|
| |
|
|
|
|
|
| 8′ 2″ |
| 859C | |
|
|
|
| |
| 8′ 3″ |
| ||
|
|
|
| |
| 8′ 4″ |
| ||
|
| XR | ||
|
|
|
| |
| 8′ 5″ | 30″ max. |
| |
|
|
|
| YZ |
| 8′ 6″ | 30″ max. |
| |
|
|
|
| ACCESSOR |
| 8′ 7″ | 30″ max. |
| |
| 8′ 8″ | 30″ max. |
| |
|
|
|
| |
| 8′ 9″ | 30″ max. |
| |
|
|
|
| |
| 8′ 10″ | 30″ max. |
| |
| 8′ 11″ | 30″ max. |
| |
|
|
| ||
|
|
|
|
|
| 9′ 0″ | 30″ max. |
|
|
| 9′ 1″ | 30″ max. |
|
|
|
|
|
|
|
| 9′ 2″ | 30″ max. |
| C |
|
|
|
| |
| 9′ 3″ | 30″ max. | 8510 | |
|
|
| ||
| 9′ 4″ | 30″ max. | ||
|
|
|
| R |
| 9′ 5″ | 30″ max. |
| |
|
| ZX | ||
| 9′ 6″ | 30″ max. |
| |
|
| Y | ||
|
|
|
| |
| 9′ 7″ | 30″ max. |
| |
|
| ACCESSOR | ||
|
|
|
| |
| 9′ 8″ | 30″ max. |
| |
|
|
|
| |
| 9′ 9″ | 30″ max. |
| |
| 9′ 10″ | 30″ max. |
| |
|
|
|
| |
| 9′ 11″ | 30″ max. |
|
POWER SUPPLY
IMPORTANT - (Please read carefully)
WARNING:
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before beginning installation.
Do not use an extension cord or adapter plug with this appliance. Follow National electrical codes or prevailing local codes and ordinances.
Electrical supply
This vent hood must be supplied with 120V, 60Hz, and connected to an individual, properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or time delay fuse.
•Wiring must be 2 wire with ground.
•If the electrical supply does not meet the above requirements, call a licensed electrician before proceeding.
•Route house wiring in the ceiling, as close to the installation location as possible. Allow an addi- tional 3 feet length from ceiling joists to reach the junction box on the hood.
•Connect the wiring to the house wiring in accor- dance with local codes.
Grounding instructions
The grounding conductor must be connected to a ground metal, permanent wiring system, or an
WARNING: The improper connection of the
TOOLS AND MATERIALS
REQUIRED (NOT SUPPLIED)
| 10′ 0″ | 30″ max. |
|
|
|
|
|
|
|
| *Based on 36″ countertop height. |
|
|
|
|
| |||
ZV850SB Duct Cover Dimensions |
| ||||||||
Recirculating | A |
| B |
|
|
|
|
| |
|
|
|
|
|
| ||||
Installation |
|
|
|
|
| B | |||
ZXR858C |
| 15″ |
|
|
|
|
| ||
|
|
|
|
|
| ||||
|
|
|
|
|
| ||||
ZXR859C | ″ | ″ | A | ||||||
|
|
|
|
| |||||
ZXR8510C | 26″ |
|
|
|
| ||||
| |||||||||
|
|
|
|
|
|
|
4
•Tape measure
•Knife
•Spirit level
•Wire cutter/stripper
•Wire nuts
•Electric drill and 5/32” bit
•Phillips and
•Hammer
•Pliers
•Center punch
•10 mm Hex wrench/socket
•Safety glasses
•Duct tape
•Plumb
•Gloves to protect against sharp edges
•120V 60Hz. 15 or 20 Amp, 2 wire with ground. Properly grounded branch circuit.
•Strain relief for junction cover
•6” round duct, length to suit installation