Generac 004614-1 owner manual Fuel Consumption GAL/HR, Engine OIL Requirements, Generator

Section 1 – General Information

QUIETPACT™ 65D Recreational Vehicle Generator

◆ 1.5.2 FUEL CONSUMPTION (GAL/HR)

Model	No Load	Half Load	Full Load
QUIETPACT™ 65D	0.28	0.45	0.78
(004614-1)

◆ 1.5.3 ENGINE OIL REQUIREMENTS

Use a high-quality detergent oil with American Petroleum Institute (API) classification “For Service CC.” Detergent oils keep the engine cleaner and reduce carbon deposits. Use oil having the following SAE vis- cosity rating, based on the ambient temperature range anticipated before the next oil change:

Temperature	Oil Grade (Recommended)
Above 100º F (38º C)	SAE 15W-40* or SAE 40
40º to 100º F (4.4º to 38º C)	SAE 10W-30 or SAE 30
Below 40º F (4.4º C)	SAE 5W-20 or 5W-30

* - in units from the factory

Crankcase and oil filter capacity is approximately 3.5 L or 3.7 U.S. quarts. Do NOT use special additives. See Sections 3.1 and 3.2 (Page 12) for oil level check- ing and changing procedures.

◆1.5.4 COOLANT

Use a 50:50 mixture that is half low silicate, ethylene glycol base antifreeze and half soft water. Use only soft water and only low silicate antifreeze. If desired, you may add a high-quality rust inhibitor to the rec- ommended coolant mixture. When adding coolant, always add the recommended 50-50 mixture.

Do not remove the radiator pressure cap while the engine is hot; otherwise, serious burns from boiling liquid or steam could result.

Ethylene glycol base antifreeze is poisonous. Do not use your mouth to siphon coolant from the radiator, recovery bottle, or any container. Wash your hands thoroughly after handling. Never store used antifreeze in an open contain- er because animals are attracted to the smell and taste of antifreeze, even though it is poiso- nous to them.

◆ 1.5.5 ENGINE

Type of Engine		ISM Diesel
Cylinder Arrangement		3, in-line
Displacement		58.2 in3. (954 cc)
Bore		2.95 in. (75 mm)
Stroke		2.83 in. (72 mm)
Compression Ratio		23-to-1
Combustion Chamber Type		Pre-Combustion
Rated Horsepower		13 @ 1,950 rpm
Cylinder Block		Cast Iron
Number of Main Bearings		4
Number of Teeth on Flywheel		104
Type of Governor		Mechanical, Fixed Speed
Fuel Filter	Full Flow Spin-On (Part # 69858)
Oil Filter		Full Flow with Bypass Valve
		(Part # 126-70939)
Oil Pressure		29-71 psi
Type of Cooling System		Pressurized, Closed Recovery
Cooling Method		Liquid-cooled
Type of Cooling Fan		Centrifugal Puller
Cooling System Capacity		1.4 U.S. gals (5.3 L)
Air Cleaner	Disposable Filter (Part # C4880)
Starter		12-volt DC Electric
Recommended Battery		70 Ah, 360 Cold-cranking
		Amps (Minimum ratings)
Maximum Cranking Current		220 Amps
Ground Polarity		Negative

◆1.5.6 GENERATOR

Rated Maximum Continuous AC Output at ...

85º F (29º C) Ambient	6,500 Watts (6.5 kW)
Rated Voltage	230 Volts AC*
Rated Maximum Continuous AC Current at ...
6,500 Watts
230 Volts	28.2 Amps
Phase	Single
Rotor Speed at No Load	3,150 rpm
Number of Rotor Poles	2
Engine RPM	1,950
Rated AC Frequency	50 Hz
Battery Charge Voltage	14 Volts DC
Battery Charge Current	2 Amps (max)
Weight	486 Pounds
Length	36.6 inches (929 mm)
Width	23.8 inches (604 mm)
Height	22.3 inches (567 mm)

Do not use any chromate base rust inhibitor with ethylene glycol base antifreeze; or else, chromium hydroxide (“green slime”) will form and cause overheating. Engines that have been operated with a chromate base rust inhibitor must be chemically cleaned before adding eth- ylene glycol base antifreeze. Using any high-sil- icate antifreeze boosters or additives will also cause overheating. We also recommend that you DO NOT use any soluble oil inhibitor for this equipment.

6 Generac® Power Systems, Inc.