General Information

H-100 Control Panel Technical Manual

This is a typical first System Diagnostics page. It dis- plays ten of the discrete inputs into the H-100 Control Panel. Inputs to the controller are internally pulled to 5 v, so to activate an input you must short it to ground.The following names are normally assigned to these inputs:

#12 Activate Emissions Module or Preheat

Press the “ENTER” button.

#1 Key switch in AUTO position #2 Key switch in MANUAL position #3 Emergency Stop Active

#4 Remote 2-wire start Active #5 Battery Charger Failure

#6 Rupture Basin or Low Fuel Pressure #7 Transfer Switch in Line Power Position

#8 Transfer Switch in Emergency Power Position #9 Modem is connecting or connected

#10 Modem is present Press the “ENTER” button.

This is a typical second System Diagnostics page. It displays ten of the discrete outputs out of the H- 100 Control Panel. Outputs from the controller are generally open collector. This means that they sink current through a load and you will NOT see any volt- age change on them when they are activated, unless they are connected to a load. These outputs can be temporarily inverted from this page. Extreme caution should be exercised while inverting outputs since it can result in operation of starters, fuel solenoids, etc. To invert an output, use the arrow buttons to position the cursor on the output value to be inverted. Press the “ENTER” button. The output will be inverted for approximately 2 seconds and then return to normal control. Only one output can be inverted at a time and leaving the page cancels all output inversions.

Press the “ENTER” button.

The above two pages are typical System Diagnostics Analog Input pages. The analog channel values that are displayed are the “raw” unprocessed data and are 10 bit numbers ranging from 0 - 1023 represent- ing a voltage or current on the analog input channel. The following names are normally assigned to these inputs:

PAGE 3-6 LINE 2:

#1 A current (CT1) #2 B current (CT2)

#3 C current (only three phase) (CT3)

PAGE 3-6 LINE 3:

#4 A-B voltage (A-N if single phase) (Vsense1) #5 B-C voltage (B-N if single phase) (Vsense2) #6 C-A voltage (only three phase) (Vsense3)

PAGE 3-6 LINE 4:

#7 Oil Temperature (AN1)

PAGE 4-6 LINE 1:

#8 Coolant Temperature (AN2)

The following names are normally assigned to these outputs:

#1 Key switch in AUTO position #1 Activate Starter Relay

#2 Activate Fuel Relay

#3 Activate Alarm/Warning Relay (Buzzer) #4 Activate Gas Relay on 13.3L Engines #5 Auxiliary Discrete Output #1

#6 Auxiliary Discrete Output #2

#7 Auxiliary Discrete Output #3

#8 Auxiliary Discrete Output #4

#9 Activate Ignition Module on 13.3L Engines

#9 Oil Pressure (AN3) #10 Coolant Level (AN4)

PAGE 4-6 LINE 2:

#11 Fuel level (AN5)

#12 Auxiliary Analog Input (AN6) #13 Throttle Position Sensor (AN7)

PAGE 4-6 LINE 3:

#14 Emissions Oxygen Sensor (AN8)

#15 Battery Charger Current (AN9)

#16 Battery Voltage

20

Page 21 Page 23
Page 22
Image 22
Generac Power Systems H-100 technical manual General Information
Page 21 Page 23

H-100 specifications

Generac Power Systems H-100 is an innovative and robust product that has garnered attention for its reliability and performance in power generation. This generator is primarily designed for both residential and commercial applications, providing a seamless backup power solution during outages.

One of the standout features of the H-100 is its powerful engine. Equipped with a state-of-the-art gas engine, this generator can deliver up to 100 kW of power, ensuring that homes, businesses, and critical facilities remain operational even in the most challenging conditions. The engine is engineered for efficiency and longevity, reducing maintenance needs and minimizing fuel consumption.

Another significant aspect of the H-100 is its advanced Smart Management System. This technology ensures optimal power usage by intelligently distributing the electrical load among connected devices. By prioritizing essential circuits, the generator maximizes efficiency and prolongs operational time during power outages.

The H-100 also boasts a remarkable noise reduction feature. Its innovative design includes sound attenuation measures, allowing the generator to operate quietly, which is particularly beneficial in residential areas where noise pollution can be a concern. This focus on quieter operation enhances user comfort and complies with noise regulations.

Durability is a key characteristic of the Generac H-100. Constructed with high-quality materials, it is designed to withstand harsh weather conditions and heavy usage. This generator is built for longevity, providing users with reliable performance and peace of mind.

The H-100 is also equipped with a user-friendly control panel. This intuitive interface allows users to monitor the generator's performance, manage settings, and perform necessary maintenance checks easily. The integration of remote monitoring capabilities enables users to assess the generator's status from anywhere, adding an extra layer of convenience.

Lastly, Generac Power Systems offers comprehensive support and resources for H-100 users. Their commitment to customer service includes accessible informational materials, a reliable warranty program, and a national network of service professionals. This ensures that users receive the assistance they need to maintain their generators optimally.

In summary, the Generac Power Systems H-100 stands out as a reliable, efficient, and user-friendly power generation solution. With its robust engine, smart management system, noise reduction features, and durable construction, it is well-suited to meet the demands of both residential and commercial applications.
Top Page Image Contents