Manuals / Genie / Lawn and Garden / Utility Vehicle

Genie Z-45, Z-25J manual Controls, Operators Manual, Platform Control Panel

Models: Z-45, Z-25J Z-45, Z-25

1 59

Download 59 pages 37.07 Kb

Page 24

Manual background

Operator's Manual	Fourth Edition · First Printing

Controls

Platform Control Panel

1Horn button

Push the horn button and the horn will sound. Release the horn button and the horn will stop.

2Platform level switch

Move the platform level switch up and the level of the platform will raise. Move the platform level switch down and the level of the platform will lower.

3Platform rotate switch

Move the platform rotate switch to the right and the platform will rotate to the right. Move the platform rotate switch to the left and

the platform will rotate to the left.

4Jib boom up/down switch

Move the jib boom switch up and the jib boom will raise. Move the jib boom switch down and the jib boom will lower.

5Auxiliary power switch

Use auxiliary power if the primary power source (engine) fails.

Simultaneously hold the auxiliary power switch to either side and activate the desired function.

6Drive speed select switch

Machine on incline symbol: Low range operation for inclines.

Machine on level surface symbol: High range operation for maximum drive speed.

7Glow plug switch

Move the glow plug switch to either side and hold for 3 to 5 seconds.

8Engine start switch

Move the engine start switch to either side to start the engine.

9Engine idle (rpm) select switch

Move the engine idle select switch to the turtle position for foot switch activated low idle. Move the engine idle select switch to the rabbit position for foot switch activated high idle.

10Gasoline/LPG models: Fuel select switch

Move the fuel select switch to the gasoline position to select gasoline. Move the fuel select switch to the LPG position to select LPG.

11Red Emergency Stop button

Push in red Emergency Stop button to the off position to stop all functions and turn the engine off. Pull out the red Emergency Stop button to the on position to operate the machine.

22

Z-45/25 • Z-45/25J

Part No.114339

Image 24

Genie Z-45, Z-25J manual Controls, Operators Manual, Platform Control Panel

Contents

IC Power Australia with Maintenance InformationOperator’s Manual Z-4525 Z-4525JContents Contact usOwners, Users and Operators Introduction DangerDo Not Operate Unless 1 Avoid hazardous situationsSafety Sign Maintenance Introduction Hazard ClassificationIntended Use Symbol and Hazard Pictorials Definitions Symbol and Hazard Pictorials Definitions Operators ManualGeneral Safety Safety signs and locationsGeneral Safety Safety signs and locationsOperators Manual Fourth Edition · First PrintingGeneral Safety Safety signs and locationsFourth Edition · First Printing Operators ManualGeneral Safety Safety signs and locationsOperators Manual Fourth Edition · First PrintingGeneral Safety Safety signs and locationsFourth Edition · First Printing Operators ManualGeneral Safety Safety signs and locationsOperators Manual Fourth Edition · First PrintingPersonal Safety Fall Protection Work Area Safety Electrocution Hazards Tip-overHazardsWork Area Safety Work Area Safety Operators ManualWork Area Safety Operation on Slopes Hazards Fall Hazards Collision HazardsWork Area Safety Work Area Safety Explosion and Fire Hazards Bodily Injury HazardDamaged Machine Hazards Component Damage HazardsWork Area Safety Battery Safety Burn Hazards Explosion HazardElectrocution Hazard Lockout After Each UseLegend Controls Platform Control PanelControls Fourth Edition · First PrintingControls Operators ManualPlatform Control Panel Controls Fourth Edition · First PrintingGround Control Panel ControlsControls Fourth Edition · First PrintingGround Control Panel Controls Operators ManualInspections Pre-operationInspection Fundamentals 2Always perform a pre-operationinspectionDo Not Operate Unless Inspections Pre-operationInspection Inspections Function Test Fundamentals 3Always perform function tests prior to useDo Not Operate Unless Inspections At the Ground ControlsTest Emergency Stop Test the Machine FunctionsTest the Foot Switch At the Platform ControlsTest the Horn Test Machine FunctionsTest the Drive Enable System Test Drive and BrakingInspections Test Limited Drive Speed - Standard Base Models Test Limited Drive Speed - Narrow Base ModelsInspections Test the Lift/Drive Select Function if equipped Test Aircraft Protection Package if equippedInspections Test Auxiliary ControlsFundamentals Inspections Workplace Inspection4Inspect the workplace Do Not Operate UnlessInspections Inspection for Decals with Words Part NoDecal Description QuantityInspections Ground Controls Side Drive Chassis Platform Engine SideFourth Edition · First Printing Operators ManualInspections Inspection for Decals with Symbols Part NoDecal Description QuantityInspections Ground Controls Side Drive Chassis Platform Engine SideFourth Edition · First Printing Operators ManualOperating Instructions Do Not Operate Unless 5Only use the machine as it was intendedFundamentals Starting the Engine Operating InstructionsEmergency Stop Auxiliary ControlsOperating Instructions Operation from Ground Operation from PlatformTo Position Platform To Steerrun rise Driving on a slopeTo determine the slope grade Operating InstructionsMachine Not Level Indicator Light if equipped Drive EnableGenerator if equipped Drive Speed SelectCheck Engine Light if equipped Aircraft Protection Package if equippedAfter Each Use Operating InstructionsFree-wheelConfiguration for Winching Transport and Lifting InstructionsObserve and Obey Securing to Truck or Trailer for Transit Securing the Platform - Z-45/25Securing the Chassis Securing the Platform - Z-45/25JLifting Instructions Y AxisX Axis Transport and Lifting InstructionsMaintenance Check the Engine Oil Level Maintenance Symbols LegendObserve and Obey Maintenance Check the Hydraulic Oil Level Maintenance Check the BatteriesCheck the Tire Pressure Maintenance Scheduled Maintenance Specifications Standard Base ModelsZ-45/25no jib Maximum slope rating, stowed position, 2WDSpecifications Standard Base ModelsZ-45/25Jjib Maximum slope rating, stowed position, 2WDSpecifications Narrow Base ModelsZ-45/25no jib Maximum slope rating, stowed positionSpecifications Narrow Base ModelsZ-45/25Jjib Maximum slope rating, stowed positionSpecifications Fourth Edition · First PrintingOperators Manual Part No.114339