Manuals / Genie / Lawn and Garden / Utility Vehicle

Genie Z-45, Z-25J manual Test the Lift/Drive Select Function if equipped, Inspections

Models: Z-45, Z-25J Z-45, Z-25

1 59

Download 59 pages 37.07 Kb

Page 36

Test the Lift/Drive Select Function (if equipped)

Operator's Manual	Fourth Edition · First Printing

Inspections

Test the Oscillate Axle (oscillating axle-equipped models)

46Start the engine from the platform controls.

47Drive the right steer tire up onto a 6 inch / 15 cm block or curb.

Result: The three remaining tires should stay in firm contact with the ground.

48 Drive the left steer tire up onto a 6 inch / 15 cm block or curb.

Result: The three remaining tires should stay in firm contact with the ground.

49 Drive both steer tires up onto a 6 inch / 15 cm block or curb.

Result: The non-steer tires should stay in firm contact with the ground.

Test Auxiliary Controls

50Shut the engine off.

51Pull out the red Emergency Stop button to the on position.

52Press down the foot switch.

53Simultaneously hold the auxiliary power switch on and activate each function control handle or toggle switch.

Note: To conserve battery power, test each function through a partial cycle.

Result: All boom and steer functions should operate. Drive functions should not operate with auxiliary power.

Test the Lift/Drive Select Function (if equipped)

54 Press down the foot switch.

55Move the drive control handle off center and activate a boom function toggle switch.

Result: No boom functions should operate. The machine will move in the direction indicated on the control panel.

56Repair any malfunctions before operating the machine.

Test Aircraft Protection Package (if equipped)

57Move the gray bumper at the bottom of the platform 4 inches / 10 cm in any direction.

58Activate each function control handle or toggle switch.

Result: All boom and steer functions should not operate.

59Move the function override switch to either side.

60Activate each function control handle or toggle switch.

Result: All boom and steer functions should operate.

34

Z-45/25 • Z-45/25J

Part No.114339

Image 36

Genie Z-45, Z-25 manual Test the Lift/Drive Select Function if equipped, Test Aircraft Protection Package if equipped

Contents

IC Power Australia with Maintenance InformationOperator’s Manual Z-4525 Z-4525JContents Contact usOwners, Users and Operators Introduction DangerDo Not Operate Unless 1 Avoid hazardous situationsSafety Sign Maintenance Introduction Hazard ClassificationIntended Use Symbol and Hazard Pictorials Definitions Symbol and Hazard Pictorials Definitions Operators ManualGeneral Safety Safety signs and locationsGeneral Safety Safety signs and locationsOperators Manual Fourth Edition · First PrintingGeneral Safety Safety signs and locationsFourth Edition · First Printing Operators ManualGeneral Safety Safety signs and locationsOperators Manual Fourth Edition · First PrintingGeneral Safety Safety signs and locationsFourth Edition · First Printing Operators ManualGeneral Safety Safety signs and locationsOperators Manual Fourth Edition · First PrintingPersonal Safety Fall Protection Work Area Safety Electrocution Hazards Tip-overHazardsWork Area Safety Work Area Safety Operators ManualWork Area Safety Operation on Slopes Hazards Fall Hazards Collision HazardsWork Area Safety Work Area Safety Explosion and Fire Hazards Bodily Injury HazardDamaged Machine Hazards Component Damage HazardsWork Area Safety Battery Safety Burn Hazards Explosion HazardElectrocution Hazard Lockout After Each UseLegend Controls Platform Control PanelControls Fourth Edition · First PrintingControls Operators ManualPlatform Control Panel Controls Fourth Edition · First PrintingGround Control Panel ControlsControls Fourth Edition · First PrintingGround Control Panel Controls Operators ManualInspections Pre-operationInspection Fundamentals 2Always perform a pre-operationinspectionDo Not Operate Unless Inspections Pre-operationInspection Inspections Function Test Fundamentals 3Always perform function tests prior to useDo Not Operate Unless Inspections At the Ground ControlsTest Emergency Stop Test the Machine FunctionsTest the Foot Switch At the Platform ControlsTest the Horn Test Machine FunctionsTest the Drive Enable System Test Drive and BrakingInspections Test Limited Drive Speed - Standard Base Models Test Limited Drive Speed - Narrow Base ModelsInspections Test the Lift/Drive Select Function if equipped Test Aircraft Protection Package if equippedInspections Test Auxiliary ControlsFundamentals Inspections Workplace Inspection4Inspect the workplace Do Not Operate UnlessInspections Inspection for Decals with Words Part NoDecal Description QuantityInspections Ground Controls Side Drive Chassis Platform Engine SideFourth Edition · First Printing Operators ManualInspections Inspection for Decals with Symbols Part NoDecal Description QuantityInspections Ground Controls Side Drive Chassis Platform Engine SideFourth Edition · First Printing Operators ManualOperating Instructions Do Not Operate Unless 5Only use the machine as it was intendedFundamentals Starting the Engine Operating InstructionsEmergency Stop Auxiliary ControlsOperating Instructions Operation from Ground Operation from PlatformTo Position Platform To Steerrun rise Driving on a slopeTo determine the slope grade Operating InstructionsMachine Not Level Indicator Light if equipped Drive EnableGenerator if equipped Drive Speed SelectCheck Engine Light if equipped Aircraft Protection Package if equippedAfter Each Use Operating InstructionsFree-wheelConfiguration for Winching Transport and Lifting InstructionsObserve and Obey Securing to Truck or Trailer for Transit Securing the Platform - Z-45/25Securing the Chassis Securing the Platform - Z-45/25JLifting Instructions Y AxisX Axis Transport and Lifting InstructionsMaintenance Check the Engine Oil Level Maintenance Symbols LegendObserve and Obey Maintenance Check the Hydraulic Oil Level Maintenance Check the BatteriesCheck the Tire Pressure Maintenance Scheduled Maintenance Specifications Standard Base ModelsZ-45/25no jib Maximum slope rating, stowed position, 2WDSpecifications Standard Base ModelsZ-45/25Jjib Maximum slope rating, stowed position, 2WDSpecifications Narrow Base ModelsZ-45/25no jib Maximum slope rating, stowed positionSpecifications Narrow Base ModelsZ-45/25Jjib Maximum slope rating, stowed positionSpecifications Fourth Edition · First PrintingOperators Manual Part No.114339